algam VULKANPRO Vertical Smoke Machine 1500W User Manual

algam 1500W  VULKANPRO Vertical Smoke Machine User Manual

Thank you for choosing one of our Algam Lighting products. Please read this user’s manual carefully and follow the instructions to avoid danger or damage to the unit due to mishandling. Keep this user’s guide for future reference

SAFETY INSTRUCTIONS

The symbols shown above are internationally accepted symbols to warn of potential hazards related to the use of electrical dangers associated with the use of electrical equipment. If any of these symbols are present on your device, please read the following instructions:

ATTENTION !
Before using your equipment, we recommend that you read all the instructions in this manual.

ATTENTION !
This device produces an intense and powerful light. Risk to the eyes. Do not look directly into the beam.

DANGER !
Hazardous voltage, risk of electric shock. Do not open the product. To reduce the risk of electric shock do not expose this equipment to rain or moisture.

ATTENTION !
Risk of burns. The exterior of the unit can become very hot. Do not touch within 10 minutes of use.

ATTENTION !
Fire hazard. Keep all combustible and flammable materials away from the materials away from the unit during operation.

DANGER !
Safety hazard. This appliance presents a significant risk of injury. Follow the safety instructions.

Place the unit at least 50cm away from flammable materials and walls.

INSTALLATION

• Unpack and check carefully for transport damage before using the product. Never put a damaged product into operation.
• This product must be installed with strong hooks of adequate size for the weight carried. The product must be screwed to the hooks and tightened properly to prevent it from falling due to vibrations. Also check that the structure (or hanging point) can support at least 10X the weight of the hanging unit. The device must be installed by a qualified person and must be placed out of reach of the public. It is necessary to use a secondary hanging system (safety sling) approved for the weight of the device.
• This unit is intended for indoor use only. Exposing the unit to rain or moisture may result in electric shock or fire.
• Do not place the unit, speakers or any other object on top of the power cord and make sure it is not pinched.
• For proper protection against electric shock, the unit must be connected to earth (ground). The electrical supply circuit must be equipped with a fuse or circuit breaker and a differential protection device.
• Power Disconnection Notice: To disconnect the device from the power source, the power plug must be removed from the power outlet. For this reason, the device must be placed in a position that allows constant, unobstructed access to the power outlet. This way, in case of an emergency, you can disconnect the power plug immediately.
• The unit should only be installed in a well ventilated area. Make sure that no ventilation slots are blocked. To ensure adequate ventilation, leave at least 20 cm of free air space around the sides and top of the unit.

USAGE

• This appliance must not be used by persons (including children) with limited physical, physiological or mental capabilities or lack of experience and/or knowledge, unless they are supervised by a person responsible for their safety or are instructed by that person in the operation of the appliance.
• Never leave this equipment unattended.
• If you experience any problems with the unit, stop using it immediately. Do not attempt to repair it yourself. Contact your dealer or an authorized service center. There are no user replaceable parts.
• NEVER use the unit under the following conditions:
  • In areas subject to vibration or bumps,
  • In places where the ambient temperature is above 45 ° C or below 2 ° C.
  • In areas exposed to excessive dryness or humidity (ideal conditions: between 35% and 80%).
• Never use the unit near flames, flammable or explosive materials or hot surfaces. Doing so may cause a fire.
• The exterior of the unit can become very hot. It is important to avoid contact with the unit during operation and for at least 10 minutes after use.
• It is important to use the supplied power cable (grounded cable).
• Before turning on the power, make sure that the voltage and frequency of the power supply match the power requirements of the unit, as described in this manual.
• Never cut or tamper with the power cord or plug. If a power cord is provided with a ground wire, it is required for safe operation! Risk of fatal electric shock!
• Always hold the power cord by the plug. Do not pull on the cord itself and never touch the power cord with wet hands as this may cause a short circuit or electric shock.
• Do not connect this device to a dimmer pack
• DO NOT allow liquids or objects to enter the unit. If liquid is spilled on the unit, immediately UNPLUG the power supply to the unit and contact customer service.
• You must ensure that the power cord never gets wet during operation. Before a thunderstorm and/or  a lightning storm, unplug the unit from the mains.
• Under no circumstances should you open the housing of the device. If you do, your safety will not be assured. There are no operational components inside, only dangerous voltages that can give you a fatal shock!

MAINTENANCE / SERVICE

• Never attempt to disassemble, repair or modify the unit yourself. Otherwise, the warranty becomes  void. Repairs by unqualified persons may result in damage or malfunction. Please contact the nearest authorized  service center. The light source contained in this fixture should only be replaced by the manufacturer or its service agent or a person of equivalent qualification.
• Screens, lenses or UV filters should be replaced if they are visibly damaged to an extent that compromises their effectiveness, such as by deep cracks or scratches.
• The lamp should be replaced if it has been damaged or deformed by heat.
• Disconnect the unit from the mains before servicing.
• If the cable or flexible outer cord of this fixture is damaged, it must be replaced with a special cable or cord from the manufacturer or its service agent only.
• Never immerse the unit in water or any other liquid. Wipe only with a slightly damp cloth.

CONNECTORS AND CONTROLS

1. Mains power supply switch
2. XLR 3 pins DMX IN connector
3. XLR 3 pins DMX OUT connector
4. Fuse
5. POWER IN connector
6. LCD display with control panel
7. Wireless system antenna
8. Wireless DMX receiver
9. POWER OUT connector (you can connect here one more VULKAN PRO only)
10. Security hook for safety cable

REMOTE

1. ON / OFF
2. ON / OFF
3. Output volume up
4. Output volume down

OPERATION INSTRUCTIONS

Connect the fog machine only in an earthed mains outlet or extension cord.

HOW TO USE

1. Unpack the fog machine (Do not connect yet the power cable).
2. Fill the fluid tank .
3. Connect the unit to mains outlet. Turn ON the mains switch. The heating element is automatically switch ON. It will take about 4 minutes until the working temperature is reached. Display will show « warming up».
4. Once the LCD displays «Ready», you are ready to go.
5. You can now use the unit in DMX mode, is manual mode, with wireless remote controller or with wireless DMX signal transmission.

THE POWER CORD CAN ONLY BE REPLACED BY AN ORIGINAL REPLACEMENT ONE.

UNPLUG THE MAINS LEAD BEFORE FILLING THE FLUID TANK.

Press the Timer key to activate the timer function. The display shows the adjusted interval and the device counts the seconds down to “0”. After that, the fog emission is triggered at the volume adjusted under “Timer Out”. The duration depends on the settings adjusted under “Duration Set”. If you wish to deactivate the timer function, press the Timer key once more.

MANUAL CONTROL (100% OUTPUT)
Press the Manual key for immediate triggering of the fog emission at 100 % volume. Let the
Manual key loose in order to stop the fog emission.

MANUAL CONTROL (LOCKED)
Press the Lock switch for immediate triggering of the fog emission at the volume adjusted under “Volume Out”. Press the Volume switch once more in order to stop the fog emission.

DMX CONTROL
Connect the machine directly to a DMX controller or a DMX loop with multiple DMX effects. The machine uses a 3-pin XLR connector for DMX connection.

ADDRESS SETUP
Press the MODE button a number of times until Add appears on the display, with the UP / DOWN buttons  the start address may be set. The start address is defined as a first channel to which the machine will respond to. Check that there are no overlapping channels used!

Via the Menu key, you can adjust the desired settings. After pressing the menu, the display shows the  following settings:

Man Vol Out xxx %| Adjust the manual volume output within the range of 0% to 100% by means of the Up/Down keys
---|---
Interval Set xxxS| Adjust the interval between each fog emission within the range of 1 to 100S by means of the Up-/Down keys
Duration Set xxxS| Adjust the duration of each fog emission within the range of 1 to 100S
Volume Out xxx%| Adjust the volume output during the timer function within the range of 0-100%
DMX512 #xxx| Adjust the DMX address for DMX control
Wind For Class xx| NO FUNCTION for this smoke machine
Angle Set xx| NO FUNCTION for this smoke machine
LED Pro Set xx| Adjust the LED program within the range of 0 to 11
LED Spe xxx| Adjust the LED speed/strobe/fade of the LED program mode
LED Sync Set| Adjust the LED mode. Yes=LEDs work together with the smoke output, NO=LEDs are always on
Remote Out xxx%| NO FUNCTION for this smoke machine

DMX PROTOCOL

WIRELESS DMX

This ALGAM LIGHTING fixture is equipped with a DMX wireless transmission system. “WIRELESS DMX”.

PAIRING YOUR DMX FIXTURE

1. Connect the transmitter (Algam Lighting DMX-WT) to your DMX controller OUTPUT.
2. Power up transmitter and the VULKAN PRO receiver.
3. Press and hold 4 seconds on receiver button on your VULKAN PRO to reset the pairing until the status LED becomes white.(this means that receiver is now ready to be paired).
4. Press now on transmitter button to start pairing. Both receiver and transmitter will blink rapidly (transmitter in blue color and receiver in green color). The pairing is processing. Once pairing is done, the transmitter status LED is now fixed blue color and receiver status LED is fixed green color.

If Transmitter or receiver looses DMX signal, the status LED will blink slowly.

ADD A FIXTURE IN AN ACTIVE GROUP

1. Press and hold 3 seconds on receiver button on your new fixture to reset the pairing until the status LED becomes white.(this means that receiver is now ready to be paired).
2. Press now on transmitter button to start pairing. Both receiver and transmitter will blink rapidly (transmitter in blue color and receiver in green color). The pairing is processing. Once paring is done, the transmitter status LED is now fixed blue color and receiver status LED is fixed green color. The other fixtures already paired in this group with this transmitter remain paired of course.

SET UP A NEW GROUP
To set up a new group is very easy. You need one more transmitter of course. Keep the existing groups active , and start the procedure above called « Pairing you DMX fixture».

NOTES
This DMX wireless system from Algam Lighting is not limited in number of groups and in number of fixtures connected in a group

SPECIFICATIONS

• Power supply: 220-240V~ I 50 Hz
• Heat up time: 4 minutes
• Features: LCD Display, HF remote, Wireless DMX built-in
• Modes: Manual, HF remote, DMX , Timer
• DMX channels: 7
• Lighting sources: 24x10W 3in1 LED
• Oil Tank capacity: 3.5 liters
• Fog output: 800m3 /min
• Spray distance: 6 – 8m
• Electric consumption: 1500W
• Dimensions; 370x190x350 mm
• Weight: 9.1 kg

This product is subject to the European Waste Electrical and Electronic
Equipment Directive (WEEE) in its currently valid version.

Do not dispose with your normal household waste.

Dispose of this device through an approved waste disposal arm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility

This Algam Lighting product is compliant to all required UE certifications and conformed to following standard and UE directives:

2015/53/UE

RoHS 2 Directive 2011/65/EU

The UE DECLARATION OF CONFORMITY is available, if you need it, please just ask for it at : contact@algam.net

Tous droits réservés. Aucun extrait de ce manuel ne peut être
reproduit, sous quelque forme ou par quelque moyen que ce soit,sans
permission écrite de la société ALGAM.
ALGAM
2 Rue de Milan, 44470 Thouaré-sur-Loire, FRANCE

Documents / Resources

| algam VULKANPRO Vertical Smoke Machine 1500W [pdf] User Manual
VULKANPRO Vertical Smoke Machine 1500W, VULKANPRO, Vertical Smoke Machine 1500W, Smoke Machine 1500W, Machine 1500W
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>