KICHLER 59127BKT 26 Inch 2 Light Outdoor Wall Light Instruction Manual

KICHLER 59127BKT 26 Inch 2 Light Outdoor Wall Light

Product Information

The product is a lighting fixture with model number 59128. It is available in a 4-light configuration. The fixture consists of various components including upper frame, lower frame, mounting strap, outlet box, socket, canopy, countersunk screws, wall anchor screws, and wall anchors.

Product Usage Instructions

1. Start by removing the four countersunk screws from the top of the upper frame on each side of the fixture. Retain the screws. Carefully remove the upper frame from the lower frame.
2. If necessary, remove the lower frame for inspection of supply connections and relamping. To remove the lower frame after fixture installation is complete, hold it in place while removing the countersunk screws from the top of the upper frame. Then, carefully remove the lower frame from the upper frame.
3. Attach the mounting strap to the outlet box using the strap mounting screws. Adjust the mounting strap to suit the position of the fixture. Ensure that the bent tabs at the outer edge of the mounting strap point away from the wall at the 9 and 3 o’clock position.
4. Use the mounting strap as a template to mark the center of the four outer slots on the mounting surface.
5. Remove the strap mounting screws and mounting strap from the outlet box.
6. Drill 1/8 inch (3.2mm) holes in the marked positions on the mounting surface. Insert a wall anchor into each hole and tap it lightly until flush with the surface.
7. Reattach the mounting strap to the outlet box using the strap mounting screws.
8. Secure the mounting strap to the wall anchors using the wall anchor screws.
9. Follow the grounding instructions provided in the manual.
10. Depending on the type of mounting strap, either wrap the ground wire from the outlet box around the green ground screw and thread into the hole or attach the ground wire under the cupped washer and green ground screw, and thread into the mounting strap.
11. If the fixture is provided with a ground wire, connect it to the outlet box ground wire using a wire connector.
12. Make the necessary wire connections according to the reference chart provided. Connect the black or red supply wire to the corresponding wire color indicated in the chart, and connect the white supply wire to the appropriate wire color as well.

Note : When using parallel wire (SPT 1 & SPT 2), the neutral wire will be square-shaped or ridged, while the other wire will be round in shape or smooth.

INSTALLATION INSTRUCTIONS

1. Remove the four (4) countersunk screws[I] from the top of the upper frame[H] (two on each side of the fixture). Retain countersunk screws. Carefully remove the upper frame[H] from the lower frame[G].
   NOTE : Lower frame[G] should be removed for inspection of supply connections and relamping during the life of the product. To remove the lower frame after the fixture installation is complete, hold the lower frame in place while removing the four (4) countersunk screws[I] from the top of the upper frame[H], then carefully remove the lower frame from the upper frame.

2. Attach the mounting strap[A] to the outlet box[B] using the strap mounting screws[C]. The mounting strap can be adjusted to suit the position of the fixture.
   NOTE : The mounting strap should be installed with the bent tabs at the outer edge of the mounting strap pointing away from the wall, at the 9 and 3 o’clock position as shown.

3. Using the mounting strap as a template, mark the center of the four (4) outer slots as shown (Fig. 1):

4. Carefully remove strap mounting screws[C] and mounting strap[A] from outlet box.

5. Drill 1/8” (3.2mm) holes in the mounting surface at the positions that were marked in Step 3. Insert a wall anchor[K] into each hole, and lightly tap wall anchor into the mounting surface until flush.

6. Reattach the mounting strap[A] to the outlet box[B] using the strap mounting screws[C].

7. Secure mounting strap to wall anchors with four (4) wall anchor screws[J].

8. Grounding instructions: (See Illus. a or b).

9. On fixtures where the mounting strap is provided with a hole and two raised dimples, wrap ground wire from the outlet box around the green ground screw, and thread it into the hole.

10. On fixtures where a cupped washer is provided, attach the ground wire from the outlet box under the cupped washer and green ground screw, and thread into the mounting strap.
    If the fixture is provided with ground wire, connect the fixture ground wire to the outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires .

11. Make wire connections. Reference the chart below for correct connections and wire accordingly
    Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
    ---|---
    Black| White
    Parallel cord (round & smooth)| Parallel cord (square & ridged)
    Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
    Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

Note : When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)

10. NOTE : Fixture should be installed with sockets[E] facing UP as shown.
    Push canopy[F] to wall, carefully aligning the mounting screw holes in left and right side of the mounting strap with the mounting screw holes in left and right side of canopy.
    NOTE : Make sure all wires are inside the canopy and do not get pinched between the mounting strap and canopy or wall and canopy of the fixture.

11. Screw four (4) mounting screws[D] into holes in the canopy and mounting strap to attach the fixture to wall. Two on the left side and two on the right side of canopy. Tighten to secure.

12. Insert recommended bulb(s) (not included).

13. Carefully raise the lower frame[G] up over bulbs, to the upper frame[H]. Align the four (4) holes in the top of the lower frame with the four (4) holes in the upper frame.

14. While holding the lower frame in place, screw countersunk screws[I] into aligned holes and tighten to secure lower frame to upper frame

FIXTURE DIAGRAM

NOTE : Model #59128 shown (4-light configuration)

PARTS LIST

• [A] Mounting Strap
• [B] Outlet Box (not supplied)
• [C] Strap Mounting Screw (2)
• [D] Mounting Screw (4)
• [E] Socket
• [F] Canopy
• [G] Lower Frame
• [H] Upper Frame
• [I] Countersunk Screw (4)
• [J] Wall Anchor Screw (4)
• [K] Wall Anchor (4)

CAUTIONS

CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING:
This fixture is intended for installation by the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS

AND/OR IN WET LOCATIONS:

1. The mounting surface should be clean, dry, flat, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
2. With silicone caulking compound, caulk completely around where the back of the canopy meets the wall surface to prevent water from seeping into the outlet box.

CLEANING:

• Always be certain that the electric current is turned off before cleaning.
• Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

© 2023 Kichler Lighting LLC. All rights reserved.
For warranty information please visit: kichler.com/warranty
We’re here to help 866-558-5706 Hrs: M-F 9am to 5pm EST

References

• Kichler® Warranty Information | Kichler Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>