LED One LOC-EXIT-2WGLW-SCOM LED White and Green Exit Sign Installation Guide

LED One LOC-EXIT-2WGLW-SCOM LED White and Green Exit Sign

SAFETY INSTRUCTIONS

Read instructions carefully before attempting to install fixture.

• All wiring should be performed by a qualified electrician.
• Disconnect power before installing or servicing. This fixture must be wired in accordance with the National Electrical Code and applicable local codes and ordinances.
• Proper grounding is required to ensure personal safety.
• Do NOT use this equipment for other than its intended use.

CAUTION: Risk of fire

• WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
• WARNING: When re-lamping, only use lamps specified by the manufacturer. Using other lamp types may result in transformer damage or unsafe conditions.
• WARNING: Battery in this unit may not be fully charged. After electricity is hooked up to the unit, let the battery charge for at least 24 hours. Then normal operation of this unit should take effect (when applicable).
• WARNING: Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel. Flexible conduit only. Maximum mounting height is 15.19FT (4.62m).
• WARNING: Do NOT use outdoors.
• WARNING: Do NOT mount near gas or electric heaters.
• WARNING: This fixture is furnished with a low voltage battery dropout circuit to protect the battery from over-discharge after the out-put has been used. Allow 20 hours recharge time after installation or power failure for full-load testing or usage.

CLEANING & MAINTENANCE

CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.

1. Clean lens with non-abrasive cleaning solution.
2. Do NOT open fixture to clean the LED. Do NOT touch the LED.

Note: These instructions do not cover all details or variation in equipment, nor do they provide for every possible situation during installation, operation or maintenance.

BATTERY: Disconnect AC power and unplug battery before servicing.

The battery supplied with the battery backup model does not require maintenance. However, it should be tested periodically (see Testing below) and replaced when it no longer operates the connected fixtures for the duration of a 30-second or 90-minute test. The battery supplied in this equipment has a life expectancy of 3 years when used in a normal ambient temperature of 72°F

TESTING

• National Electric Code (NEC) and NFPA life safety code regulations require that routine tests need to be performed as listed below:
  • Once every month, the unit needs to be tested for a duration of 30-seconds.
  • Push in and hold the test switch to perform this test.
  • Once every 12 months, a full 90-minute (per UL requirements) test needs to be performed on the unit.
  • Disconnect the power to the unit and leave it in the emergency mode.
  • The LEDs should stay ON for at least 90 minutes.
    

LAMP CAP INSTALLATION

1. Remove the face cover by gently prying it open with a flat screwdriver. (Fig. 1)
2. Pass the wires from the lamp heads through the fixture mounting holes of the housing. Insert the lamp heads into the housing and twist them to lock firmly. (Fig. 2)
3. Connect the wires of the lamp into the PCB terminal. (Fig. 3)
4. Install the face cover back on. (Fig.4)
   
   

MOUNTING OPTIONS

WALL MOUNTING: Maximum mounting height is 15.19FT (4.62m).

1. Open the front cover using a flat screwdriver.

2. Knockout appropriate mount screw hole and cable hole. (Fig. 1)

3. Mount the back plate on the wall after feed building AC supply cable into the back plate. (Fig. 2)

4. Make electrical connections inside the J-box. Cap unused wires. (Fig. 2)
   A. For 120V, use the BLACK and WHITE wires.
   B. For 277V, use the RED and WHITE wires.

5. Attach the plate to the junction box. (Fig. 3)

6. Secure the faceplate to the housing and remove the proper arrow as requested. (Fig. 4-5)
   

CEILING MOUNTING: Maximum mounting height is 15.19FT (4.62m).

1. Open the front cover using a flat screwdriver.

2. Remove the mounting hole cover on the top of side of the unit.

3. Make electrical connections inside the J-box. Cap unused lead with wire nuts provided. (Fig. 1)
   a. For 120V, use the BLACK and WHITE wires.
   b. For 277V, use the RED and WHITE wires.

4. Feed excess wire into the junction box and secure the back plate to the junction box so that it is securely fastened and tight against the ceiling. (Fig. 2)

5. Assemble the canopy and attach the fixture to the junction box. (Fig. 3)

6. Secure the faceplate to housing and remove the proper chevron(s) as requested. (Fig. 4-5)
   

DOUBLE FACE INSTALLATION: (For ceiling mounting only)

Customer Support

Phone: (844) LEDONE6 | Fax: 1-510-217-9461 | Web: www.ledonecorp.com

References

• Energy Saving with LED Lighting Fixtures & Bulbs | LED One Corporation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>