DYNATRAC DT927627P 20-Up Jt 3 Inch Rear 2.5 Endurosport Ir Instruction Manual
- June 13, 2024
- DYNATRAC
Table of Contents
DT927627P INSTALLATION INSTRUCTIONS
2-22-2020 REV.B
DT927627P 20-Up Jt 3 Inch Rear 2.5 Endurosport Ir
7392 Count Cir, Huntington Beach, CA 92647
Phone: 714-596-4461
| PART # | DESCRIPTION |
|---|---|
| DT927627P | 20-UP JT 3” REAR 2.5 ENDUROSPORT IR |
COMPONENTS INCLUDED
(2) DT124957NR-AL 20-UP JT 1.5″ REAR 2.5″ SHOCK|
HARDWARE INCLUDED
N/A|
TOOLS REQUIRED
JACK
JACK STANDS
TORQUE WRENCH
21MM SOCKET / WRENCH|
TECH NOTES
1. YOUR DYNATRAC SHOCK ASSEMBLIES COME FACTORY CHARGED TO 250 PSI. RELEASING
NITROGEN PRESSURE MAY LEAD TO SHOCK MALFUNCTION AND REDUCED RIDE QUALITY.
FAILURE CAUSED BY LOW NITROGEN PRESSURE IS NOT COVERED UNDER DYNATRAC’S
WARRANTY POLICY
2. INTENDED FOR USE WITH: DT922065 (20-UP JT 13/8″ REAR COIL SPACER KIT) OR
DT922066 (20-UP JT 2.5″ REAR MULTI-RATE SPRING KIT)
WARNING!
READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING
INSTALLATION! IF THESE INSTRUCTIONS ARE NOT PROPERLY FOLLOWED SEVERE FRAME,
SUSPENSION AND TIRE DAMAGE MAY RESULT TO THE VEHICLE!
DYNATRAC RECOMMENDS THAT YOU EXERCISE EXTREME CAUTION WHEN WORKING UNDER A
VEHICLE THAT IS SUPPORTED WITH JACK STANDS.
** DYNATRAC RECOMMENDS ALL INSTALLATION TO BE PERFORMED BY A PROFESSIONAL
SHOP/SERVICE TECHNICIAN. PRODUCT FAILURE CAUSED BY IMPROPER INSTALLATION WILL
NOT BE COVERED UNDER DYNATRAC’S WARRANTY POLICY.
INSTALLATION
- Using a properly rated jack, raise the rear of the vehicle and support the frame rails with jack stands. Ensure the jack stands are secure and set properly before lowering the jack. NEVER WORK UNDER AN UNSUPPORTED VEHICLE. Remove rear wheels.
- Remove the factory shocks using a 21mm. [FIGURE 1 & 2]
NOTE: It is easiest to install shocks at full droop. - Install the DYNATRAC rear shocks as shown using factory hardware and torque to factory spec using a 21mm. Install the longer heim spacers towards the frame to position the shock outward away from the frame. [FIGURE 3]
- Reinstall rear wheels and lower the vehicle back to the ground. [Torque lugs to factory spec]
VERIFY ALL FASTENERS ARE PROPERLY TORQUED BEFORE DRIVING VEHICLE.
RETORQUE ALL NUTS, BOLTS AND LUGS AFTER 100 MILES AND PERIODICALLY THEREAFTER.
2.5 SERIES SHOCK & COILOVER TECHNICAL INFORMATION
MAINTENANCE
DYNATRAC shock absorbers are a high quality rebuildable race style shock
absorber designed for optimal performance. With a unit of this caliber on your
vehicle, routine maintenance is required to keep them looking and operating in
like new condition. Residual oil and assembly lube may be present at all seal
paths from the factory out of the box and is considered normal. Pooling of oil
however is not acceptable at any time and one should contact the DYNATRAC
dealer where purchased.
BELOW ARE GUIDELINES BASED ON HOW YOU USE YOUR VEHICLE BUT YOUR MILEAGE MAY
VARY:
STREET USE:
- Send in for factory servicing every 40,000 miles or if a leak develops, ride quality decreases, or they begin to make excessive noise.
- Remove any buildup of road salt, mud, or debris from shocks anytime accrued
- Clean with mild soap and water with each oil change or anytime you notice build up.
- Wax the cylinders yearly with automotive wax to prevent corrosion.
- Check nitrogen pressure yearly.
STREET/DIRT:
- Send in for factory servicing every 15,000 miles or if a leak develops, ride quality decreases, or they begin to make excessive noise.
- Clean with mild soap and water with each oil change, offroad trip, or anytime you notice build up.
- Wax the cylinders yearly with automotive wax to prevent corrosion.
- Check nitrogen pressure each dirt outing.
DIRT USE:
- Send in for factory servicing every 1,000 miles.
- Check nitrogen pressure each outing.
- Remove any buildup of mud or debris from shocks after every outing.
SELF-SERVICE:
- Contact DYNATRAC for service kits & tools at 714-596-4461.
DYNATRAC SHOCK ABSORBER WARRANTY
This shock absorber has a 1 year warranty against any manufacturer’s defects.
If a shock fails within the initial year of ownership, the shock must be
shipped to DYNATRAC for inspection and service. If a shock is inspected and it
has been determined the shock failed due to neglect, damage caused by improper
installation or any other reason besides “normal wear and tear”, the owner of
said shock is responsible for all service costs. This includes labor, parts
and shipping.
DYNATRAC warrants to the original retail purchaser who owns the vehicle on
which the product was originally installed. DYNATRAC does not warrant the
product for finish, alterations, modifications and/or installation contrary to
DYNATRAC instructions. DYNATRAC products are not designed, nor are they
intended to be installed on vehicles used in race applications, for racing
purposes or for similar activities. (A “race” is defined as any contest
between two or more vehicles, or a contest of one or more vehicles against the
clock, whether or not such contest is for a prize). This warranty does not
include coverage for police or taxi vehicles, race vehicles, or vehicles used
for government or commercial purposes. Also excluded from this warranty are
sales outside of the United States of America and Canada.
DYNATRAC’S obligation under this warranty is limited to the repair or
replacement, at DYNATRAC’S discretion, of the defective product. Any and all
costs of removal, installation or re-installation, freight charges and
incidental or consequential damages are expressly excluded from this warranty.
Items that are subject to wear are not considered defective when worn and are
not covered.
DYNATRAC components must be installed as a complete kit as shown in our
current application guide. Any substitutions or exemptions of required
components will immediately void the warranty. Some finish damage may happen
to parts during shipping and is not covered under warranty.
This warranty is expressly in lieu of all other warranties expressed or
implied. This warranty shall not apply to any product that has been improperly
installed, modified or customized subject to accident, negligence, abuse or
misuse.
7392 Count Cir, Huntington Beach, CA 92647
Phone: 714-596-4461
www.dynatrac.com
https://qrcodes.pro/Kn9Sy4