KICHLER 59129BKT 28.75 Inch Black Textured Outdoor Post Lantern Instruction Manual

KICHLER 59129BKT 28.75 Inch Black Textured Outdoor Post Lantern

Product Information

• The product consists of a fixture with an upper frame (A), lower frame (B), fixture base (D), countersunk screws (C), and mounting screws (E).
• The fixture is designed to be installed on a post and is suitable for outdoor use.
• The product comes with a warranty. For more information on the warranty, please visit kichler.com/warranty.

Product Usage Instructions

1. Remove the four countersunk screws (C) from the top of the upper frame (A) (two on each side of the fixture). Keep the screws for later use.
2. Carefully remove the upper frame (A) from the lower frame (B).
3. Place the fixture base (D) onto the post. Mark the positions for the three mounting screw holes on the post using the fixture base as a template. Make sure the fixture is facing the desired direction for final installation.
4. Remove the fixture base from the post.
5. Drill 3/16 (4.76mm) holes in the post at the positions marked in Step 3.
6. Grounding instructions: Refer to Illus. a or b for grounding options.
7. Make wire connections according to the reference chart below:

Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

Note: When parallel wire (SPT 1 & SPT 2) is used, the
neutral wire is square-shaped or ridged, and the other wire will be
round in shape or smooth.

8. Carefully place the fixture base (D) back onto the post and secure it in place using the three mounting screws (E). The screws should slip into the holes drilled in the post.
9. Insert the recommended bulbs (not included) into the fixture.
10. Place the upper frame (A) on top of the lower frame (B) and align the four holes in the top of the lower frame with the four holes in the upper frame (two on each side of the fixture).
11. Screw the countersunk screws (C) into the aligned holes and tighten them to secure the upper frame to the lower frame.

Please refer to the provided diagrams for a visual representation of the product and its installation steps.

FIXTURE DIAGRAM

PARTS LIST

• [A] Upper Frame
• [B] Lower Frame
• [C ] Countersunk Screw (4)
• [D] Fixture Base
• [E] Mounting Screw (3)

CAUTION – RISK OF SHOCK:

• Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING:

1. This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

• Always be certain that electric current is turned off before cleaning.
• Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

1. Remove the four (4) countersunk screws[C] from the top of upper frame[A] (two on each side of fixture). Retain countersunk screws. Carefully remove upper frame[A] from lower frame[B].

2. Carefully slip fixture base[D] onto post. Using the fixture base as a template, mark the positions for the three (3) mounting screw holes on the post.
   NOTE: Ensure that fixture is facing the desired direction for final installation.

3. Remove fixture base from post.

4. Drill 3/16” (4.76mm) holes in post at the positions that were marked in Step 2.

5. Grounding instructions: (See Illus. a or b).
   If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.

6. Make wire connections. Reference the chart below for correct connections and wire accordingly.

Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)|

1. Carefully slip fixture base[D] onto post and secure in place using three (3) mounting screws[E]. Screws should slip into holes drilled in post.
2. Insert recommended bulbs (not included).
3. Carefully place upper frame[A] on top of lower frame[B]. Align the four (4) holes in the top of the lower frame with the four (4) holes in the upper frame (two on each side of fixture).
4. Screw countersunk screws[C] into aligned holes and tighten to secure upper frame to lower frame.

• © 2023 Kichler Lighting LLC. All rights reserved.
• For warranty information please visit: kichler.com/warranty

Documents / Resources

| KICHLER 59129BKT 28.75 Inch Black Textured Outdoor Post Lantern [pdf] Instruction Manual
59129BKT 28.75 Inch Black Textured Outdoor Post Lantern, 59129BKT, 28.75 Inch Black Textured Outdoor Post Lantern, Textured Outdoor Post Lantern, Outdoor Post Lantern, Post Lantern, Lantern
---|---

References

• Kichler® Warranty Information | Kichler Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>