DMCS1-B Motorized Cellular Shade with Dual Motor Instruction Manual
- June 13, 2024
- DMCS
Table of Contents
1-B Motorized Cellular Shade with Dual Motor
Instruction Manual
DMCS1-B Motorized Cellular Shade with Dual Motor
| NO. | Item | Specification |
|---|---|---|
| 1 | Power Source | DMCS1-B: Li-ion Battery |
| 2 | Input | DMCS1-B: 24V, 1.5A Max |
| 3 | Output | DMCS1-B: 10.89V, 1.3A Max. |
| 4 | Radio type | 2.4G RF |
| 5 | Motor type | Brush DC motor |
| 6 | Charging type | Power Charger PB-01S Power Charger PB-02 |
| 7 | Charging Time | < 2 hours |
| 8 | Charging Temperature | 5°C — 35°C / 41°F — 95°F |
| 9 | Operating Temperature | 0°C — 40°C / 32°F — 104°F |
| 10 | Relative Humidity | 0% — 90% (Non-condensing) |
READING BEFORE INSTALLATION
WARNING! Important safety instructions. Follow all instructions since
incorrect installation can lead to severe injury.
Before installing the device, remove any unnecessary cords or components and
disable any equipment not needed for powered operation.
WARNING! The installation height will vary according to product type or
installation situation and may exceed 98.43″ (2.5m).
WARNING! For the shade powered by battery (DMCS1-B), please turn on the
shade AFTER installation. Press and hold the shade button for 3 seconds, and
the green light will flash, which means the shade is powered on.
Reserve space before installation :
For Model# DMCS1-B：with built-in Li-ion battery pack and charging accessories.
IMPORTANT! For Model #DMCS1-B with built in Li-ion battery pack, please mount
the headrail correctly. Make sure the headrail is level and that it doesn’t
tilt forward. Improper installation may cause the charging wand to not make
full contact with the charging port. The shade installation only allows up to
3° of deflection tolerance.
TOOLS YOU WILL NEED
- Level
- Measuring Tape
- Pencil
- Power Drill (6mm hex driver and drill bit)
- Screwdriver
You will need to use the following fasteners for your particular mounting surface.
| Wood | Fastener |
|---|---|
| Surface | Screws (Provided) |
| Drywall/Plaster | Wall Anchors, Expansion Bolts (Not Provided) |
| Metal | Sheet Metal Screws (Not Provided) |
GETTING STARTED
Check Standard Components/Hardware:
Hardware Standard
Quantity:
| Order Width (X) | Less or Equal to 64″ | Between 64-1/8″ and 112″ | Over 112″ |
|---|---|---|---|
| Installation Bracket | 2 | 3 | 4 |
| Installation Bracket Screw | 4 | 6 | 8 |
| Spacer Block (Optional) | Varies per order request: 1 pc / bracket or |
2pcs/bracket
Hold Down Bracket (Optional)| 2| 2| 2
Hold Down Bracket Screw (Optional)| 4| 4| 4
Check Components for DMCS1-B for Battery:
Charging Wand (Optional)
MOUNTING INSTALLATION BRACKETS
The installation bracket may be used for INSIDE or OUTSIDE mounts.
Mounting the brackets level is essential for proper operation of the shade.
Shim the brackets if necessary to achieve a level alignment. The bracket
requirements and placement are the same for inside and outside mount. Measure
8” from both ends of the headrail. Mark the bracket location on the mounting
surface. Proper alignment of brackets will make installation easier.
Inside Mount:
Allow a minimum of 1/16” distance from the front of brackets to the edge of
window opening as shown in the drawing on the right. Use two installation
screws to secure brackets. Use wall anchors for drywall or plaster wall. * For
shallow mounting, use 2 flat head screws to secure the bracket as shown in the
drawing on the right. Outside Mount:
Use 2 flat head screws to secure each bracket. Use wall anchors for drywall or
plaster wall. Note: If spacer block is provided, please follow this guide:
Please always make sure the raised side of the spacer block is against the
bracket. Install the Shade:
Position the head rail at an angle so that it is hooked to the front of the
bracket. Then push it upward at the back to snap into the bracket.
Note: You will hear a click sound once the head rail is properly
secured.
Install Hold Down Bracket (Optional):
A. For Hold Down Brackets. Use screw to secure each bracket. B. For Magnetic
Hold Down
Use M3x15mm screw to secure the magnet catch at the below location. Make
sure the magnet catch align with the pre-installed magnet on shade bottom
rail.
REMOVE THE SHADE
Fully raise the shade, and then gently remove the bracket off the headrail
with a flat screwdriver. Remove the shade. 
Congratulations!
You have finished installing the product.
To ensure a perfect user experience, we encourage you to follow the QR code
below to browse additional resources, including how to operate, how to charge
and troubleshooting guides. Please also note that for shades with rechargeable
batteries, the current charge level of the batteries is about 50%.
FCC ID: Q3V-DMCS1
IC ID: 28542-DMCS1
CAN ICES-003 (B) / NMB-003(B)
https://www.nienmade.com/qrcode/GUD_DMCS%20Installation%20Instruction%20A4.pdf
Documents / Resources
| DMCS
DMCS1-B Motorized Cellular Shade with Dual
Motor
[pdf] Instruction Manual
DMCS1-B Motorized Cellular Shade with Dual Motor, DMCS1-B, Motorized Cellular
Shade with Dual Motor, Cellular Shade with Dual Motor, Shade with Dual Motor,
Dual Motor, Motor
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>