easee Charge Core Charging Robot Instruction Manual
- June 13, 2024
- easee
Table of Contents
Important product information
Charging Robot
Charge Core, Charge Lite, One, Plug & Play and Ready
Charge Core Charging Robot
The information in this leaflet applies to all Easee Charging Robots (Charge
Core, Charge Lite, One, and respective Plug & Play versions) and Easee Ready,
unless specified otherwise. Keep this information for future reference.
Read this information carefully before installing and operating the product.
The Installation guide and User guide are an integral part of the product
documentation. All information is available online at
easee.com/manuals
Installation of this product requires a mobile device with NFC or Bluetooth
support. Operation of the product using the app features requires a mobile
device with Bluetooth support.
Intended use
The Charging Robot is intended for AC charging of electrically-powered
vehicles equipped with non-gassing batteries. It is intended for indoor or
outdoor use. The specifications comply with the properties of the electrical
grid and the electrically-powered vehicle, and the ambient conditions. The
connection to the vehicle is using a global standard type 2 cable (IEC 62196).
The AC input to the product is intended for a hardwired installation that
complies with local and national regulations.
If installed with other chargers of the same model it is additionally intended
to communicate with the other chargers to prevent overloads by balancing the
power used in charging multiple electrically-powered vehicles at the same
time.
Easee Ready is intended solely as a prepared charging point for an Easee
Charging Robot.
If you use the product in any way other than described in the related
documentation, it could result in damage to property, injury, or possibly
death.
For Austria, Finland, Germany, Netherlands, Switzerland: The Charging Robot is
a home-charging device manufactured and designed strictly for residential use
only.
The Charging Robot shall not be used for non-residential use. Residential use
is to be understood as use in or around an individual’s own residence. The
Charging Robot at all times must make use of an individual’s private
connection to the electricity grid. The Charging Robot cannot be used for
charging electric vehicles for which reimbursement is desired, based on the
realized consumption of electricity. The Charging Robot cannot be used to
calculate this consumption.
For Belgium, Croatia, Czech Republic, Denmark, Estonia, France, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, UK:
The Charging Robot is not MID compliant. In some markets, MID compliance is
not a requirement yet for charging electric vehicles for which reimbursement
is expected or consumption is reported as a cost in tax filings; please check
local rules for more information.
Operating conditions
The Charging Robot shall only be used with a charging cable according to IEC 62196 and IEC 62893. The product must be firmly mounted on a vertical unperforated wall or structure that covers the entire back side of the product and has a sufficient load-bearing capacity. It may only be operated within the approved operating parameters (see Technical specifications in the Installer guide).
Safety instructions
WARNINGS AND CAUTIONS
A Warning indicates a condition, hazard or unsafe practice that can result in
serious personal injury or death.
A Caution indicates a condition, hazard or unsafe practice that can result in
minor personal injury or damage to the product.
WARNING
- This product shall only be installed, repaired or serviced by an authorised electrician. All applicable local, regional and national regulations for electrical installations must be respected.
- Danger to life due to high electrical voltage. Never make any changes to components, software or connected cables.
- The installation must not be carried out in the vicinity of explosive atmospheres or in areas where there is a risk of flowing water.
- The terminals in the backplate are energised when the power circuit is closed and must never be in direct contact or in contact with anything other than the plugin electronics (Chargeberry).
- Never use or touch the product if it is damaged or does not function properly.
- In case of a critical error, the charger will alert the user with a warning sound and flashing red light on the light strip. Turn off the power and remove the charging cable from the Charging Robot. The power can then be turned back on if necessary. The flashing red light will continue, but the warning sound will stop when the charging cable is disconnected. The charger is blocked from further use, cannot be reset and has to be replaced. Contact customer support.
CAUTION
- If a fire occurs, use CO2 for extinguishing. To extinguish it with water or foam, the system must be first de- energized (electrically disconnected).
- Never clean the product with high pressure or running water.
- Do not immerse the product in water or other liquids.
- Never touch the contacts of the Type 2 socket and never insert foreign objects into the product.
- Never use the charging cable if it is damaged or if the connections are wet or dirty.
- Do not use extension cords or adapters in combination with the product.
- Avoid direct sunlight for optimal operation in all weather conditions.
- Do not use the product near strong electromagnetic fields or in the direct vicinity of radio transmitters.
- The product must be installed on a permanent location. The connections of the Chargeberry and backplate are designed for a limited number of plugging cycles.
- Make sure that children do not play with the product.
- Make sure the charging cable does not cause a tripping hazard or risk being run over by a car.
- The charging cable must only be removed from the Charging Robot by pulling the plug handle, not by pulling the cable.
Additional important information
Simplified Declaration of Conformity
Hereby, Easee ASA declares that Charge Core, Charge Lite and Plug & Play
defined in this manual are in conformance with the EU Radio Equipment
Directive 2014/53/EU and RoHS Directive 2011/65/EU.
Hereby, Easee ASA declares that Easee Ready is in compliance with the Low
Voltage Directive 2014/35/EU and RoHS Directive 2011/65/EU.
Hereby, Easee ASA declares that Easee One and Charge Core defined in this
manual and sold in the UK after January 2023 are in compliance with the UK
Radio Equipment Regulations 2017 and RoHS regulations 2012.
The full text of the EU Declaration of Conformity is available at:
easee.com/DoC
The full text of the UK Declaration of Conformity and the UK Smart Charging
Regulations Statement of Compliance and Technical File are available at the
following internet address: easee.com/manuals
Transportation
The product should always be transported within its original packaging. No
other items should be stored on top of the box other than Easee chargers.
Should the box be dropped or otherwise impacted, a visual inspection should be
done in order to verify potential damage.
Storage
The electronics are sealed and will not get damaged if stored in humid areas.
However, in order to preserve the packaging and its contents, we recommend
storage in a tempered, dry and well-ventilated area. Relative humidity should
not exceed 80% and no corrosive gas should be present. Storage or
transportation environment must never exceed the limits provided in the
Technical specifications.
Dismounting
Perform a factory reset of the device before powering it down. This is done
via the Installer App. Dismounting of the backplate shall only be performed by
an authorised electrician. The power supply to the charger must be isolated
before dismounting starts. Use the installation guide and follow the steps in
reverse in order to dismount the product in the correct order.
Data protection
When the product connects to the Internet, personal data is sent to Easee ASA.
You will receive more information about data protection during the
configuration of your Charging Robot.
Waste handle
A crossed-out dustbin (WEEE symbol) indicates that a product and its
accessories must not be disposed of in household waste at the end of their
lifecycle. For the return of old devices, free collection and acceptance
points may be available in your vicinity. Observe local regulations for
correct and environmentally friendly disposal. If the old electronic equipment
contains personal data, you are responsible for deleting it yourself before
returning it.
Warranty
The product is free from material defects and is in accordance with laws and
regulations for consumer protection in the country where the product is
purchased. All correctly installed Easee hardware is covered by our 3 years
limited warranty. If your charger needs to be repaired within this warranty
period, please contact your Easee supplier. Further information can be found
at easee.support
Some countries may have extended warranty.
Returns and complaints
Contact your distributor or Easee Customer Support regarding the return and
complaint of your product.
Customer support
Download the latest manuals, find answers to frequently asked questions and
useful documents and videos for your product at easee.support
Max transmitted power
| WLAN (802.11b.g.n) | 12.25 dBm, 16.8 mW at 2.4 GHz |
|---|---|
| SRD (non-specific) | 13.5 dBm, 22.5 mW at 868 Mhz |
| LTE | FDD bands 1, 3, 8, 20 & 28 |
| LTE band 1 | 21 dBm at 1920-1980 MHz, 2110-2170 MHz |
| LTE band 3 | 21 dBm at 1710-1785 MHz, 1805-1880 MHz |
| LTE band 8 | 21 dBm at 880-915 MHz, 925-960 MHz |
| LTE band 20 | 21 dBm at 832-862 MHz, 791-820 MHz |
| LTE band 28 | 21 dBm at 703-748 MHz, 758-803 MHz |
| Bluetooth | 3.4 dBm, 2.2 mW at 2.4 GHz |
| RFID reader | 3.3 dBuA/m (3m) at 13.56 MHz |
The information in this document is for information purposes only, is provided as is, and may be subject to change without notice. Easee ASA, including its subsidiaries, does not accept any liability for the correctness or completeness of the information and illustrations, and is not liable or responsible for your considerations, assessments, decisions or absence of such, or other use of the information in this document.
No part of this publication may be re-published, reproduced, transmitted or re-used in any other form, by any means or in any form, for your own or any third-party’s use, unless otherwise agreed with Easee or its subsidiaries in writing. Any permitted use shall always be done in accordance with good practice and ensure that no harm may be caused to Easee or by misleading the consumer.
Easee and Easee products, product names, trademarks and slogans, whether registered or not, are Easee’s intellectual property and may not be used without Easee’s prior written permission. All other products and services mentioned may be trademarks or service marks of their respective owners.
August 2023 – Version 1.01
© 2023 by Easee ASA. All rights reserved.
Easee ASA
Grenseveien 19
4313 Sandnes, Norway
www.easee.com