VOLLRATH R3873346 Cafeteria Breath Guard Instruction Manual

June 1, 2024
VOLLRATH

VOLLRATH-LOGO

VOLLRATH R3873346 Cafeteria Breath Guard

VOLLRATH-R3873346-Cafeteria-Breath-Guard-product

Product Information

Specifications

  • Product Name: Vollrath Cafeteria Breath Guard
  • Model: One Piece and Three Piece
  • Item No.: 2350030-01 Rev 04/12

FAQ

  • Q: What should I do if I accidentally over tighten the cap nuts during installation?
    • A: If you accidentally over tighten the cap nuts, stop immediately to prevent cracking of the plastic components. Loosen the cap nuts slightly and ensure they are securely fastened without excessive force.
  • Q: Can I disassemble the breath guard for cleaning?
    • A: Yes, you can disassemble the breath guard by following the installation steps in reverse order. Clean each component separately using mild soap and water, then reassemble according to the instructions.
  • Q: How do I contact Vollrath for further assistance?
    • A: You can contact Vollrath Company at the provided telephone numbers or visit their website for additional support and service inquiries.

These instructions cover the installation of the one pice Cafeteria Breath Guard and the three piece Cafeteria Breath Guard.

One Piece Breath Guard Installation

Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:

NOTE: Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

VOLLRATH-R3873346-Cafeteria-Breath-Guard-fig-1

  1. Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
  2. Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
  3. Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
  4. Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.

Three Piece Breath Guard Installation

Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:

NOTE: Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

VOLLRATH-R3873346-Cafeteria-Breath-Guard-fig-2

  1. Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
  2. Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
  3. Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
  4. Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
  5. Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
  6. Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.

Contacts

The Vollrath Company, L.L.C.

  • 1236 North 18th Street Sheboygan, WI 53081-3201 U.S.A.
  • Main Tel: 800.628.0830
  • Service Tel: 800.628.0832
  • FAX: 800.752.5620

Vollrath of Canada, Co.

  • Tel: 800.695.8560
  • FAX: 800.752.5620

www.vollrathco.com

© 2010 The Vollrath Company, L.L.C.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

VOLLRATH User Manuals

Related Manuals