BRANDMOTION FVMR-1180 FullVUE Mirror Instructions

FullVUE® Rear Camera Mirror for Ford
Super Duty (1999 – 2016)
FVMR-1180

FVMR-1180 FullVUE Mirror

Recommended Tools

Difficulty Level Install Time

45m – 75m
Questions? Call the Brandmotion technical support line at 734-619-1250 or CLICK HERE

Kit Contents

Components for installing the FVMR-1180 Kit Contents:
FullVUE® Mirror & Harness
3rd Brake Light Bezel & Camera
9m Camera Harness

Installation of the FullVUE Mirror & Wire Connections

1. Remove the old mirror from the mount on the windshield as per manufacturer’s directions.
Be sure to use the proper removal tool if required.
2. Install new mirror onto the D-tab and tighten with a Phillips screwdriver.
CAUTION
Take care not to overtighten. Overtightening could result in damage to your windshield.|
Part 2| Powering the FullVUE® Mirror
1. Connect the power harness to the plug on the mirror. Route the harness across the top of the head liner, along the windshield, and down the A-pillar, and to the desired location in the kick panel.
2. Ensure that the harness will not be pinched when trim panels are replaced.|
Part 3| Wiring the FullVUE Mirror
1. Connect the RED wire from the mirror harness to 12-volt accessory power.
2. Connect the YELLOW wire from the mirror harness to 12-volt constant power.
3. Connect the BLACK wire to a solid ground. Chassis ground in the kick panel is recommended.|
Part 4| Function test of the FullVUE Mirror
1. Turn the vehicle ignition on and see if you are seeing the front camera displayed on the screen. Turn off the ignition and the mirror will power down|

Disassembly

1. Use a Phillips screwdriver to remove the screws on either side of the brake light
2. Pull the brake light out from the cab. Be Careful not to damage the foam gasket around the opening.
3. Disconnect the power connector from the light.|

Running Wires

1. Connect the 9m camera harness to the mirror harness at the connection by the mirror.
2. Run the 9m camera harness from the FullVUE Mirror through the headliner toward the brake light.
3. Pull the video connector of the 9m camera harness through the grommet to the outside
of the cab.|

Assembly

1. Attach the thick foam gasket to the back side of the bezel or to the light. Whichever piece does not have a foam gasket from the factory.
Note: The cable for the camera must go through the channel of the bezel before the foam is put overtop
2. Put the foam side of the bezel against the vehicle.
3. Connect the rear camera harness to the camera. Make sure to line up the arrows on the connectors
4. Plug the brake light back into the cab plug
5. Put the screws through the hole of the light and insert the light into the bezel.
6. Use the screws that are showing through the bezel to line up with the screw holes of the vehicle. ( Be careful not to scratch the vehicle.)
7. Screw the assembly back together with the factory screws.|

Adjustment

1. If you need to change the camera’s pitch, gently bend the bracket until it reaches the desired view angle.|

FullVUE® Mirror Settings

FullVUE® User Interface Guide|
---|---
1. Touch screen once to bring up User Interface
2. Swipe finger left or right to switch camera views
3. Use +/- on left side of screen to adjust brightness
4. Use icons below for respective controls|

FullVUE® Mirror Settings

Streaming Media
– Toggle NightSight On/Off (Turn on under low light conditions for clearer image on mirror)
-Choose: StandardVideo for regular use / EnhancedVideo for crisp color / Evening Light for
sunset or dusk lighting conditions
Protect Level
– Select sensitivity for auto locked event recording for DVR. When the G-Sensor feels shock, it will automatically lock the recording on the SD card for later use
– Choose: On/Off
Parking Monitoring
– Select On/Off for G-Sensor Initiated recording.
These files will be auto locked and recored for 1 min.| Volume
– Adjust UI control and video playback volume
Clock Settings
– Set date and time for UI
L CD Power Save
– Select automatic screen save Off/1min/3min
– Screen will go black after 1min or 3min of no use, if selected
Format SD
– Format/Reformat Card. Be sure to save all wanted footage on another device befoe reformatting
Refresh   Rate
– Adjust video frame rate 50hz or 60hz (frames per second)
– This setting will change how smooth the video will play back and will excessively, try changing
this setting
Factory Reset
– Reset all settings
FullVUE® User Interface Guide| Video Recording Menu Instructions
Normal Video
– This is where all general video recordings can be found. All files in this folder will be overwritten if SD card runs out of space. DVR will overwrite the oldest files first.
Locking Video
– Pushing the “Lock Recording” button on the main user interface (shown on page 3) will save the respective video in this folder. All files saved in this folder will not be overwritten, even if the SD card runs out of space.
Photo
– This folder will hold all screenshots taken using the “Screen Capture” button on the main user interface shown on page 3.
Front and Rear
– Front and Rear camera views are separated in each main folder. Use fron or rear button to view recordings or photos of the desired camera view.| Protect and Unprotect
– These functions will not protect the video from being overwritten. Protecing a photo or recording
means that if the “Delete All” function is used, the protected files will not be deleted. If you do not
want to delete specific files, protect them and “Delete All” will delete all other fiels iniside of the
folder. See “Delete All” for functional details.
Delete
– This button will delete only individually selected files. If the files is protected, it will not delete that
file.
Delete All
– The function will delete all unprotected files within a folder. It will not delete files in both front
and rear. It will only delete files in the folder and camera view you have open.
-In other words, if you are viewing all files saved under Normal Video – Front and push “Delete
All”, only front camera files will be deleted. Rear camera files will still be saved.

FAQ Section

1. Can you flip the camera in the FullVUE® Screen?

- At this time you cannot flip the image from the FullVUE® camera. Please check back with our website for the latest information.

2. Can I turn the display off and use the FullVUE® as a mirror?

- Yes! Simply tap the bottom button 1 time ( 2 times if you have the time stamp screen) and the mirror will function as a traditional mirror.

3. Can I use an auxiliary camera with the FullVUE® mirror?

- At this time, you can only use the provided FullVUE® Camera with the FullVUE® Rear Camera Mirror. Please visit our website for new information.

Vehicle Application:
Ford Super Duty (1999 – 2016)
Part Number: FVMR-1180

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>