zelmer ZIR2620 Steam Iron User Manual
- June 13, 2024
- zelmer
Table of Contents
zelmer ZIR2620 Steam Iron User
WARNING
PLEASE READ THE INSTRUCTIONS FOR USE CAREFULLY PRIOR TO USING THE PRODUCT. STORE THESE IN A SAFE PLACE FOR FUTURE REFERENCE
DESCRIPTION
- Spray button
- Shot of steam button
- Steam regulator
- Water inlet lid
- Spray nozzle
- Level mark for maximum filling
- Temperature control
- Clean button
- Soleplate
- Pilot light
- Power cord
SAFETY INSTRUCTIONS
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
If the supply cord is damaged it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
The iron must not be left unattended while it is connected to the supply
mains.
The plug must be removed from the socket-outlet before the water reservoir is
filled with water.
The iron must be used and rested on a flat, stable surface When placing the
iron on its stand, ensure that the surface on which the stand is placed is
stable.
The iron is not to be used if it has been dropped, if there are visible signs
of damage or if it is leaking.
Keep the iron and its cord out of reach of children less than 8 years of age
when it is energized or cooling down. This device is designed for use at a
maximum altitude up to 2000m above sea level.
CAUTION Hot surfaces. Surfaces are liable to get hot during use.
IMPORTANT WARNINGS
This appliance is designed for home use and should never be used for
commercial or industrial use under any circumstances. Any incorrect use or
improper handling of the product shall render the warranty null
and void.
Prior to plugging in the product, check that your mains voltage is the same as
the one indicated on the product label.
If you use one adaptor make sure it can reach 16 A and is provided with earth
socket.
The mains connection cable must not be tangled or wrapped around the product
during use.
Do not use the device, or connect and disconnect to t supply mains with the
hands and / or feet wet. Do not pull on the connection cord in order to unplug
it or use it as a handle Do not direct steam at people and animals.
Do not place the appliance under the tap to fill the water tank, or immerse it
in water or other liquids. Unplug the product immediately from the mains in
the event of any breakdown or damage and con- tact an official technical
support service. In order to prevent any risk of danger, do not open the
device. Only qualified technical personnel from the brand´s Official technical
support service may carry out repairs or procedures on the device. Only an
official technical support service centre may carry out repairs on this
product.
Proceed according to maintenance and cleaning section of this manual for
cleaning B&B TRENDS SL. disclaims all liability for damages that may occur to
people, animals or objects, for the non-observance of these warnings..
BEFORE THE FIRST USE
Some parts of the steam iron have been slightly greased and as a result the
iron may slightly smoke when switched on for the first time. After a short
time this will cease.
Remove protection cover from the soleplate and clean it with a soft cloth.
HOW TO USE
Always check whether a label with ironing instructions is attached to an
article to be ironed. Follow these instructions in all cases.
Turn the temperature control (7) dial round to set the appropriate temperature
indicated in ironing instructions or in fabric label.
| MARKING | MATERIAL, FOR EXAMPLE |
|---|---|
| Do not iron this material | |
| • (1 dot) | Synthetics, Nylon, Acrylics, Polyester, Rayon |
| • • (2 dots) | Wool, Silk |
| • • • (3 dots) | Cotton, Linen |
Insert the main plug into the wall socket. The indicator light (10) will turn
on.
When the indicator light goes out you may start ironing.
If you set the temperature control to lower setting after ironing at a high
temperature. it is not recommended to iron before the pilot light switches on
again.
WATER TANK FILLING
Unplug the iron from the mains before filling the water tank.
The iron has been designed to use normal tap water. If the tap water in your
area is hard or semi-hard, mix tap water with distilled or demineralized
water purchased in stores in the ratio 2:1 and 1:1 respectively (distilled
water / tap water).
You can inquire about the water hardness with your local water supplier.
Never use 100% distilled or demineralized water, rain water, softened water,
scented water, water from refrigerators and air conditioners, dryers or other
types of home water preparation water.
Open the water inlet lid (4).
Slowly pour water through the water inlet.
Never fill beyond the level mark for maximum filling (6), in order to avoid
spilling out of water.
Close the water inlet lid.
Important: The water tank should be emptied after each use.
SPRAYING
This can be used to remove stubborn wrinkles.
As long as there is enough water in the water tank, you may use the spray
button at any temperature setting during steam or dry ironing.
Press the spray button (1) several times to activate the pump while you are
ironing.
Do not use the spray function with silk!
STEAM IRONING
Set the temperature control (7) to the desired position in accordance with the
manufacturer’s label. The pilot light (10) will turn on until the temperature
is reached. Then the pilot light will turn off.
Set the variable steam regulator (3) to the desired position.
Temperature control (7)| Recommended position of the steam regulator
(3)
---|---
MIN|
|
CAUTION: Avoid coming in contact with ejected steam.
DRY IRONING
The steam iron can be used on the dry setting with or without water in the
water tank.
Turn the steam regulator (3) to the minimum position.
Select the setting on the temperature control (7) best suited for the fabric
to be ironed.
CAUTION: If the steam iron has been used for a long time, it is hot and there
is no water. Do not refill it with water until the steam iron cools down.
SHOT OF STEAM
The shot of steam feature provides additional steam for removing stubborn
wrinkles.
Set the temperature control (7) to “MAX”.
Press the shot of steam button (2) to release the burst of steam.
NOTE: To prevent water leakage from the soleplate, do not keep the steam
button pressed for more than 5 seconds.
VERTICAL IRONING
This can be used to remove creases from hanging clothes, curtains etc.
Hang article of clothing on a clothes hanger.
Set the temperature control (7) to “MAX”.
Operate the iron in a vertical position at a distance of 10 cm / 4 in, and
press the shot of steam button (2) repeatedly with pauses of at least 5
seconds.
NOTE: To prevent water leakage from the soleplate, do not keep the steam
button pressed for more than 5 seconds.
ANTI-DRIP SYSTEM
With the anti-drip system, you can perfectly iron even the most delicate
fabrics.
Always iron these fabrics at low temperatures. The plate may cool down to the
point where no more steam comes out, but rather drops of boiling water that
can leave marks or stains. In these cases, the Anti-drip system automatically
activates to prevent vaporization, so that you can iron the most delicate
fabrics without risk of spoiling or staining them.
WHEN YOU FINISH IRONING
Set the temperature control (7) to the minimum position.
Remove the main plug from the wall socket.
Empty the water tank.
Stand the iron on heel rest.
MAINTENANCE AND CLEANING
Before cleaning the steam iron ensure it is unplugged from the power supply
and has completely cooled down.
Do not use abrasive cleaners.
To clean exterior surfaces, use a damp soft cloth and wipe dry. Do not use any
chemical solvents, as these will damage the surface
To clean the soleplate, do not use scouring pads or harsh cleaners on the
soleplate as these will damage the surface.
To remove burnt residue, iron over a damp cloth while iron is still hot. To
clean the soleplate, simply wipe with soft damp cloth and wipe dry.
SELF-CLEANING
It is recommended to do the self-cleaning at least every two weeks.
- Fill the water tank.
- Set the temperature control (7) to its maximum position.
- Set the steam regulator (3) to the minimum position.
- Insert the main plug into the wall socket.
- Allow the iron to heat up until the indicator light (10) goes out.
- Unplug the steam iron (very important!)
- Hold the iron horizontally over a sink
- Press the clean button (8) and shake the iron until approximately one third of the water capacity of the tank is evaporated. Warning: boiling water and steam will be ejected from the holes in soleplate with impurities washed out.
- Release the clean button, and gently shake the iron for some seconds.
- Repeat steps 8 and 9 three times until the tank is empty.
- Then plug the iron in and heat it up again until the remaining water has evaporated.
- Push the clean button a few times more to clean the valve.
- Unplug the iron and let the soleplate cool down.
- Move the iron over an old (preferably) piece of cloth. This ensures that the soleplate will be dry during storage.
Do not use chemical additives, scented substances or decalcifies. Failure to comply with the abovementioned regulations leads to the loss of guarantee.
ANTI-CALC SYSTEM
A special resin filter inside the water reservoir softens the water and
prevents scale build-up in the plate.
The resin filter is permanent and does not need replacing.
Please note: Use tap water only. Distilled and/demineralized water makes the
“Zero-Calc”, anti-calc system ineffective by altering its physicochemical
characteristics.
AUTO SHUT OFF
When steam iron kept stable, To protect the steam iron and save the energy, It
will automatic shut off the power. Usually , The iron be stabled with
verticality within 8 minutes, And the horizontal lever, within 30 seconds.
TROUBLE SHOOTING
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|
| Soleplate (9) is not heating even through iron is turned on | Connection | |
| problem | Check main power supply cable plug and outlet | |
| Temperature control (7) is at “MIN” position | Turn to a higher position, if |
com- partible with the fabric
Steam does not come out| Not enough water in the tank.| Fill the water tank.
Steam regulator (3) is selected in non-steam position.| Set the steam
regulator between positions of minimum steam and maximum steam.
Selected temperature is lower than that specified to use with steam.| Set to a
higher temperature, if compatible with the fabric.
Shot of steam / vertical ironing function does not work| Iron is not hot
enough| Set a suitable temperature and wait until the pilot light (10) goes
out.
Selected temperature is lower than that specified to use with steam.| Set a
higher temperature, if com- partible with the fabric
Water drips out of the soleplate (9) together with steam| Temperature control
(7) set to a low position.| Turn to a higher position (between “••” and
“MAX”), if compatible with the fabric.
Steam regulator (3) is set too high in conjunction with a low temperature.|
Set the steam regulator to a lower setting (see “Steam ironing” section).
You have pressed the shot of steam button (2) repeatedly without waiting for 5
seconds between each press.| Wait 5 seconds between each press of the shot of
steam button
Deposits come out through the holes of the soleplate (9)| Traces of lime scale
are coming out of the steam chamber.| Carry out a self-cleaning process.
Spray function does not work| Not enough water in the tank.| Fill the water
tank.
The clothes tend to stick| The temperature is too high.| Turn the temperature
control (7) down and wait until the iron has cooled down. Set a suitable teem-
perature for the cloth to be ironed.
The iron produces vapours and odours| This may be caused by the lubrication of
some of the internal parts| This is completely normal and will stop after a
short while
PRODUCT DISPOSAL
This product complies with European Directive 2012/19/EU on electrical and
electronic devices, known as WEEE (Waste Electrical and Electronic Equipment),
provides the legal framework applicable in the European Union for the disposal
and reuse of waste electronic and electrical devices. Do not dispose of this
product in the bin, instead going to the electrical and electronic waste
collection centre closest to your home.
We hope that you will be satisfied with this product.
