LUTEC 5198106012 Tubular Wall Light Connected by WiZ Owner’s Manual
- June 5, 2024
- LUTEC
Table of Contents
LUTEC 5198106012 Tubular Wall Light Connected by WiZ Owner’s
IMPORTANT
RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
AWARNING:
WiZ products only work with 2.4G routers. If your router does not have a 2.4G
setting then return the product back
to the place of purchase.
For assistance, please contact our customer service hotline Monday-Friday
9:00a.m-5:00p.m Eastern Standard Time
Toll Free 1-877-714-8669 (English
speaking only)
LUTEC USA CUSTOMER SERVICE
149-B Houston Rd Troutman, NC 28116
E-mail: senvice@lutec.net
Website: www.lutec.cem
PACKAGE CONTENTS
SPECIFICATIONS
Model: 5198106012
Lumens: 950LM
Total power: 18W
Voltage: 110V-120V
Hertz : 60Hz
Measurements: 3.07 in. x 4.72 in. x 9.64 in./7.8 cm x 12.0 cm x 24.5cm
ASAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble,
operate or install
the product.
WARNING:
Consult a qualified electrician if you are not certain about the installation
process. Always install wiring connections in accordance with local code,
ordinances and the National Electric Code. Changes or modifications to this
unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment. This light fixture is designed
to fit standard junction boxes as defined by the National Electrical Code.
NOTICE :
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures Reorient or relocate the receiving antenna. Increase
the separation between the equipment and receiver. Connect the equipment into
an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV techrnician for help.
REPARATION
Before beginning to assemble or installing lighting fixture, make sure all
parts are present. Compare parts with package contents list. If any part is
missing or damaged, do not attempt to assemble, install or operate the
product.
Estimated Assembly Time: 20-30 minutes. Tools Required for Assembly: Phillips
Screwdriver, Silicone Caulking Adhesive, Ladder.
INSTALLATION
-
Turn OFF power to work area at main circuit breaker or fuse box.
CAUTION: Do not rely on wall switch alone to turn off power. -
Remove the mounting bracket (DD) from the fixture (A) by unscrewing the pre-assembled screws (CC). Set aside screws (CC) as they will be used in a later step.
-
Run the green, white and black wires from the junction box through the mounting bracket (DD) Make sure the rectangular mounting tabs on the mounting bracket are facing the light fixture. Attach the mounting bracket (DD) to the junction box (not included) using the two mounting screws (AA). Level the mounting bracket by rotating the bracket so the two rectangular mounting tabs are horizonal/level. Then tighten screws into the junction box.
-
Locate the ground wire from the junction box and connect it to the green ground wire from the light fixture (A) by twisting a wire nut (BB) onto the bare ends of the wires. Connect the white wire from the junction box to the white wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Connect the black wire from the junction box to the black wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Position all the wires inside the fixture junction box.
-
Attach the light fixture (A) to the mounting bracket(DD) using the screws (CC) previously removed in step 2. Careful to make sure all the wires remain tucked into the fixture junction box.
-
After mounting the fixture, apply silicone caulking compound completely around the perimeter of the cover plate where the back of the cover plate meets the mounting surface. Silicone caulking prevents water from seeping into the junction box.
-
Adjust the lamp head to the desired position. Then turn ON power to work area at main circuit breaker or fuse box.
CARE AND MAINTENANCE
Clean surfaces with a mild, non-abrasive cleaner
TROUBLESHOOTING
YEAR LIMITED WARRANTY
If this product fails due to a defect in materials or workmanship within three
(3) years (Bulbs excluded) Trom tne aate or purchase, reurn t alongWitn proor
or date or purcnase and it wil be replaced with the same or comparable model
free of charge by LUTEC USA LLC. This warranty is void if damage or defect has
resulted from accident, abuse, misuse or faulty repair. This warranty gives
you specific legal rights and you may have other rights that vary from state
to state.
IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL OR
INDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS
PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAVNAr AnDLVTAvAL
HOW TO CONNECT YOUR LIGHT TO THE WiZ APP
Make sure your phone is connected to the home Wi-Fi. Wiz only works with 2.4G
network router
AVAILABLE LEMETWORKSs
Please use your smartphone in camera mode and position the camera over the QR
Code until recognized.
Then download the free WiZ app From Google Play or the App Store.
- Create Home
- Add room
- Add a device
- Enter Wi-Fi password
- Select “Smart pairing
- Searching For light
- Click “FINISH”
- Enjoy the APP
- Any problems, find us on “Suppor or call toll Free 1-877) 714-8669 (English speaking only), E-mail: service@lutec.net
websibe: www.lutec.com bo contact us.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>