aFe POWER 54-13079D Magnum FORCE Stage 2 Cold Air Intake System Instruction Manual
- June 13, 2024
- aFe POWER
Table of Contents
54-13079D Magnum FORCE Stage 2 Cold Air Intake System
advanced FLOW engineering Magnum FORCE Stage-2 Cold Air Intake System
Instruction Manual P/N: 54-13079D / 54-13079R____
- Please read the entire instruction manual before proceeding.
- Ensure all components listed are present.
- If you are missing any of the components, call customer support at 951-493-7185.
- Ensure you have all necessary tools before proceeding.
- Do not attempt to work on your vehicle when the engine is hot.
- Retain factory parts for future use.
| Label | Qty. | UoM | Description | Part Number |
|---|---|---|---|---|
| Al | 1 | Ea | Air Filter (Pro DRY S) | 24-91203D |
| A2 | 1 | Ea | Air Filter (Pro 5R) | 24-91203R |
| B | 1 | Ea | Tube | 05-5413079B1 |
| C | 1 | Ea | Housing | 05-5413078B2 |
| D | 1 | Ea | Coupling, Silicone Bellows 3-1/4″ID x 3″L | 05-01480 |
| E | 2 | Ea | Clamp. 048 | 03-50007 |
| F | 1 | Ea | Fitting. CCV Vacuum | 05-01499 |
| G | 1 | Ea | Retainer Clip, Christmas Tree Style for 1/4″ Hole | 05-01350 |
| H | 1 | Ea | Grommet. Rubber Small | 03-50268 |
| J | 1 | Ea | Grommet. Rubber Large | 03-50167 |
| K | 1 | Ea | Fitting, Intake Air Temp Sensor | 05-01454 |
| M | 35. | In | Seal, Trim: 3/4″ Bulb | 05-01507 |
Installation will require the following tools:
8mm nut driver or flat head screwdriver, 10mm socket and wrench, panel clip
pliers or similar.
Warranty Information available at: https://afepower.com/contact#warranty
Emissions Disclaimer: This product is not currently CARB exempt and is not
available for purchase in California or for use on any vehicle registered with
the California Department of Motor Vehicles.
Refer to Figure A for Steps 1-2
Step 1: Using a 10mm socket and driver, remove the (3) screws 1 securing the
OE intake to the vehicle.
Step 2: Using an 8mm nut driver, loosen the two clamps 2 on the intake tube.
Refer to Figure B for Steps 3-5
Step 3: Disconnect the two vent lines that are connected to the vacuum
generator 3 by pushing on the grey clips and sliding the tubes off the
fittings.
Step 4: Disconnect the Intake Air Temperature (IAT) sensor 4 .
Step 5: Remove the attaching clip for the IAT sensor harness 5 and move the
harness out of the way for now.
Refer to Figure C for Steps 6-8
Step 6: Remove the OE intake tube from the vehicle.
Step 7: Remove the OE housing from the vehicle by lifting straight upward. If
the rubber grommets pop off with the housing, then remove them from the
housing and place them back into the holes in the mounting bracket.
Step 8: If the attaching clip on the IAT sensor harness is bent out of shape,
then repair it so that it looks like the clip shown in the small photo. 
Refer to Figure D for Step 9-11
Step 9: Install the small rubber grommet 6 provided into the small hole on the
aFe POWER intake tube.
Step 10: Install the CCV Vacuum Fitting into the grommet as shown.
Step 11: Install the push clip 7 to retain the CCV Vacuum Fitting to the aFe
POWER intake tube. 
Refer to Figure E for Steps 12-15
Step 12: Remove the IAT Sensor from the factory intake tube by lifting the
locking tab, rotating the sensor a quarter-turn counterclockwise, and then
pulling the sensor straight out.
Step 13: Install the large rubber grommet into the large hole on the aFe POWER
intake tube.
Step 14: Install the supplied IAT Fitting into the large rubber grommet.
Step 15: Install the IAT Sensor into the IAT Fitting, and rotate it clockwise
a quarter-turn to lock it into place.
Make sure the locking tab clicks past the retainer on the IAT Fitting.
Note: The orientation of the sensor is not critical. 
Refer to Figure F for Steps 16-18
Step 16: Remove the (2) two rubber mounting grommets and steel sleeves from
the factory intake tube.
Step 17: Install the (2) two rubber mounting grommets and steel sleeves 8 into
the aFe POWER intake tube as shown.
Step 18: Install the bellows coupling 9 onto the end of the tube and
preinstall the two clamps onto the coupling. Do not tighten the clamps at this
time. 
Refer to Figure G for Steps 19-22
Step 19: Remove the rubber mounting grommet and steel sleeve from the factory
intake housing.
Step 20: Install the rubber mounting grommet and steel sleeve 10 into the aFe
POWER intake housing as shown.
Step 21: Install the trim seal 11 around the top of the housing. Make sure to
press down firmly all around the trim seal to ensure a good fit.
Step 22: Install the aFe POWER air filter into the housing and loosly install
the clamp over the filter flange. 
Refer to Figure H for Steps 23-25
Step 23: Install the housing into the vehicle and make sure that the factory
intake scoop 12 passes into the housing under the air filter .
Step 24: Press down firmly on the housing to lock the pegs into the rubber
grommets under the housing.
Step 25: Secure the housing to the fender with the factory screw 13 .
Refer to Figure I for Steps 26-28
Step 26: Install the aFe POWER intake tube into the air filter first and then
slide the coupler over the turbo inlet tube.
Step 27: Rotate the tube into postion so that the mounting tabs sit flat on
the fan shroud mounting brackets.
Step 28: Tighten all clamps at this time.
Refer to Figure J for Steps 29-30
Step 29: Connect the IAT harness to the IAT sensor on the intake tube.
Step 30: Secure the IAT harness clip 14 into the radiator fan shroud as shown.
It may be necessary to slide the clip further down on the wire so the wire is
relaxed.
Refer to Figure K for Steps 31-32
Step 31: Secure the intake tube to the fan shroud with the (2) two factory
screws 15 .
Step 32: Reconnect the (2) two vent lines 16 to the new CCV Vacuum Fitting on
the aFe POWER intake tube.
Refer to Figure L for Step 33
Step 33: Check all the components are tight and secure. Your installation is
now complete. Thank you for choosing aFe POWER!
advanced FLOW engineering, inc.
252 Granite Street Corona, CA 92879
https://afepower.com/contact
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>