JBL B Series In Wall Loudspeaker Owner’s Manual
- June 13, 2024
- JBL
Table of Contents
JBL B Series In Wall Loudspeaker
Product Information
The JBL B-Series architectural loudspeaker is designed to bring the best sound to your home. It is an in-wall loudspeaker that is suitable for standard drywall construction, ceiling, and drop ceilings with at least 3/8 wall material thickness. The loudspeaker comes with a grille, a wall cut-out template, and an owner’s manual.
Product Usage Instructions
- In-Wall Loudspeaker Placement: For stereo or home theater listening, position the loudspeakers so the tweeters are close to ear level. Position the left and right speakers closely with the television. For background listening, position the loudspeakers in any convenient location.
- Installation: Follow these steps to install the loudspeaker:
- Use the provided wall cut-out template to mark the location of the loudspeaker. Use a saw to cut the appropriate size.
- Run speaker wiring to the wall openings, complying with all local construction and building codes. Attach the speaker wire to the appropriate speaker terminals on the loudspeaker, ensuring that each wire matches the correct color and polarity on the system amplifier.
- Insert the loudspeaker into the opening and use a screwdriver to tighten the four screws on the front side. The loudspeaker brackets will clamp down on the wall material.
- If needed, paint the speaker grill before inserting it on the loudspeaker. Gently remove the cloth before painting and replace it after the paint dries. The loudspeaker grille is designed to support most types of interior paint.
- Place the grille into the loudspeaker.
- Note: Once the grille is installed, you may need to use a screwdriver to remove it from the loudspeaker.
INTRODUCTION
Thank you for purchasing your new JBL B-Series architectural loudspeaker. This
loudspeaker is designed to bring the best sound to your home. We urge you to
take a few minutes to read through this manual, which describes the product
and includes step-by-step instructions to help you set up and get started.
Customer Support: Please contact your dealer if you have any questions
about your product, its installation or its operation. For more information
about this product, or to contact JBL please visit our website at
www.JBL.com.
BOX CONTENTS
- 1 x Loudspeaker
- 1 x Loudspeaker grille
- 1 x Wall cut-out template
- 1 x Owner’s manual
MINIMUM TOOLS REQUIRED FOR INSTALLATION
- Screwdriver
- Wire strippers
- Level
- Stud Finder
- Saw
IN-WALL LOUDSPEAKER PLACEMENT
JBL B-Series in-wall loudspeakers are designed for standard drywall construction, ceiling and drop ceilings with at least 3/8″ wall material thickness. For stereo or home theater listening, position the loudspeakers so the tweeters are close to ear level, and position the left and right speakers closely with the television. (See Fig 1 &2) For background listening, position the loudspeakers in any convenient location.
In-Ceiling Speaker placement
JBL B-Series in-ceiling loudspeakers are designed for standard drywall
ceilings and drop ceilings with at least 3/8″ thick wall material. In drop
ceiling installations, JBL recommends replacing the ceiling tile with plywood
or medium-density fiberboard to prevent sagging ceiling tiles. For home
theater, position the loudspeakers as in Figure 3. For background music,
position the speakers in any convenient location to distribute the sound
throughout the room. (Figure 4)
Installation
Make sure to allow at least 1” (25.4mm) between the edge of the supplied installation template and any rafters or other obstructions behind the wall, so the speaker’s locking mechanism will have room to engage fully. Be sure that there are no studs, lengths of conduit, pipes, heating ducts or air returns in any wall/ceiling cavity that will interfere with the speaker.
- Use the provided wall cut-out template to mark the location of the loudspeaker. Use a saw to cut the appropriate size. (Figure 5)
- Run speaker wiring to the wall openings. Be sure to comply with all local construction and building codes. Attach the speaker wire to the loudspeaker’s appropriate speaker terminals. Confirm that each wire matches the correct color and polarity on the system amplifier. (Figure 6)
- Insert the loudspeaker into the opening. Use your screwdriver to tighten the four screws on the loudspeaker’s front side. The loudspeaker brackets will clamp down on the wall material. (Figure 7)
- If needed, paint speaker grill before inserting on the loudspeaker. Gently remove the cloth before painting and replace after the paint dries. This loudspeaker grille is designed to support most types of interior paint.
- Place the grille into the loudspeaker. (Figure 8)
Note: Once the grille is installed, you may need to use a screwdriver to remove the grille from the loudspeaker.
WARNING: HARMAN International assumes no responsibility for improper installation of hardware or for any personal injuries or product damages resulting from improper installation or a fallen loudspeaker.
Limited Warranty/ Specification
JBL B-Series speakers are warranted against defects. The duration of the speaker’s warranty depends on the laws in the country in which it was purchased. Your local JBL retailer can help you determine the length of your warranty.
Specifications| B- 6IC| B- 8IC| B- 6ICDT|
B- 6IW| B- 8IW
---|---|---|---|---|---
Nominal Impedance| 4 ohm| 4 ohm| 4 ohm| 4 ohm| 4 ohm
Power (WRMS/Peak)| 35/140W| 40/160W| 35/140W| 35/150W| 45/160W
Frequency Response| 50Hz – 20kHz| 45Hz – 20kHz| 50Hz – 20kHz| 50Hz –
20kHz| 45Hz – 20kHz
Loudspeaker Sensitivity| 90dB| 92dB| 90dB| 91dB| 91dB
Woofer| 6.5″ (165mm) Poly woofer| 8″ (203mm) Poly woofer| 6.5″ (165mm)
Poly woofer| 6.5″ (165mm) Poly woofer| 8″ (203mm) Poly woofer
Tweeter| 0.5″ (13mm) Polymer Tweeter| 0.5″ (13mm) Polymer Tweeter| 0.5″
(13mm) Polymer Tweeter| 0.5″ (13mm) Polymer Tweeter| 0.5″ (13mm) Polymer
Tweeter
Cutout Dimensions| 7.9″ (202mm)| 9.6″ (243mm)| 7.9″ (202mm)| 9.7″ ×
7.2″ (246mm × 182mm)| 11.7″ × 8.8″ (299mm × 223mm)
Grille Finished Dimensions| 9.1″ (232mm)| 10.7″ (272mm)| 9.1″
(232mm)| 8.4″ × 10.9″ (213mm × 277mm)| 10″ × 12.9″ (255mm × 329mm)
Mounting Depth| 3.6″ (92mm)| 3.9″ (100mm)| 3.6″ (92mm)| 3.3″ (84mm)|
3.7″ (96mm)