globe GL031TX LED 4-Light Track Bar Instruction Manual

GL031TX LED 4-Light Track Bar
Instruction Manual

GL031TX LED 4-Light Track Bar

Thank you for selecting Globe as your lighting choice for your home. With proper care, this product will provide years of pleasure and enjoyment. Carefully follow the instructions in order to ensure that this product functions safely and properly for years to come.;
FOR YOUR SAFETY:
** Most electrical accidents are caused by carelessness or ignorance. If you combine a basic knowledge of electricity, a healthy respect for it, and a dose of common sense, you can safely tackle many household electrical repairs. Here are some basic guidelines for working with electricity: Before working on a circuit, go to the main service panel and remove the fuse or trip the breaker that controls that circuit.
Tape a sign to the panel warning others to leave the circuit alone while you work. Before touching any wire, use a voltage tester to make sure it’s not live.
Whenever you check for voltage in a receptacle, check both outlets – each may be controlled by a separate wiring circuit.
When replacing fuses, turn off the main power first. Make sure your hands and feet are dry, and place one hand behind your back to prevent electricity from making a complete circuit
through your chest. Touch a plug fuse only by its insulated rim.
Remove cartridge fuses with a fuse puller.
Use tools with insulated handles and ladders made of wood or fiberglass.
Keep dry-chemical fire extinguishers in the kitchen, basement, and workshop.
Never disable grounding devices. Make sure that all appliances requiring grounding are properly grounded, and that the electrical system itself is properly grounded.
Meet or exceed all electrical code requirements that cover the work you are doing.
Always work with enough light to see what you are doing; it’s easy to make mistakes when you’re working in dim light.
When in doubt about the safety of any electrical repair or test, call in a professional.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
NOTE:** This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC+ISED
This device complies with Part 15 of the FCC Rules [and contains license- exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS standard(s)].
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation of the device.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules as this equipment has very low levels of RF energy.

ELECTRICAL INSTALLATION

FIG. 1. Place the wall switch to the “OFF” position. Depending on which type of fuse box you have in your home:
FIG. 2. Place either the main (Master) switch to the “OFF” position, cutting off power to your entire home OR turn off the individual switch that provides power to where the fixture will be installed. OR
FIG. 3. Place either the main (Master) switch to the “OFF” position, cutting off power to the entire home OR unscrew the fuse that provides power to where the fixture will be installed.

LED 4 LIGHT TRACK BAR WITH COLOR SELECT
Integrated 24 watt LED, 1600 lumens, 90CRI, 50,000 hrs, color temperature control (2000 K – 3500 K – 5000 K)

LED 4- LIGHT TRACK BAR WITH COLOR SELECT
Integrated 24 watt LED, 1600 lumens, 90CRI, 50,000 hrs, color temperature control (2000 K – 3500 K – 5000 K)

REMOTE DIMMER

This product is a 2.4GHz wireless transmission remote control. The remote control sends instructions to the receiver through radio waves.

PRODUCT SPECS：

• Battery specification:
  CR2032 (DC3V) battery included

• Remote control range:
  Within 10 m (33′)

• This product controls at least 1 light and at most 3 lights at the same time

• Dimming range: 5%-100%
  The light fixture inside this box comes pre-paired to your remote control
  Please note if you’re pairing 2+ lights to 1 remote, please follow our pairing instructions.

KEY FUNCTION DESCRIPTION

1. Measure the desired height at which you’d like to install your remote control.

2. Mark the location on the wall using a pencil. Once you’ve marked the right location, drill two holes and insert 2 wall anchors.

3. Install the wall plate on the wall at the desired height using mounting screws.
   

4. Remove the plastic insulation so the battery can make contact and start.

5. Take out the battery compartment on the remote control by sliding down.

6. The remote control attaches to the wall plate with magnets. Align the remote to the hole on the wall plate and push the remote gently into the wall plate to secure it.

Replacing your batteries
When replacing the battery, please use the same battery model CR2032 (DV3V). After installing the battery, slide the battery compartment up until it is secured in the remote control.

PAIRING TO MULTIPLE DEVICES

The same remote control can be connected to multiple light fixtures. To pair, please follow the instructions below:
Matching distance: The remote control must remain within 3M (118”) from the light fixture to be paired.
Product pairing
Method 1: Before the light fixtures are turned on, press the button on the remote control (5000 K) continuously to connect to your lights. When your lights flash 3 times, this indicates that the remote control was successfully paired with your lights.
Method 2: Switch on the power supply to turn your light fixture on. Hold down the 5000 K button on the remote control for 3 seconds while the light fixtures are on to connect to the remote control. When your light fixtures flash 3 times, this indicates that
the remote control was successfully paired with your light fixture.

• Please note only one remote control can be paired with the same light. After the light is successfully paired with the new remote control, the previous remote control can no longer be used to control your light fixture.

TROUBLESHOOTING

Your light fixture comes pre-paired with the remote control inside the box. Once you install your fixture and remote control, you should be ready to start using it. In case you experience issues during this stage, please follow the below instructions:
Matching distance: Make sure the remote control is installed within 3m (118″) from the light fixture you want to pair it with.
Product pairing: Switch on the power supply of the light to turn the light on. Hold down the blue button on the remote control (5000 K) continuously for 3 seconds when the light is on. You should see the light flash 3 times, indicating that the remote control is successfully paired with the light and you’re ready to start using it.

Retry within 3 seconds after power-on
Your main power supply is not turned on| Turn on the switch to power on
The remote control is not functional| The battery power is at 0| Replace the battery – battery model CR2032 (DC3V)
Failed to match| Retry within 3 seconds after power-on
The remote is too far from the light fixture| Use the remote control within 10M of the light fixture
Too many obstructions| Remove obstructions that can affect signal transmission
Matched more than 3 lights| Rematch the lights you want to use
There are wireless devices with the same frequency in close range| Turn off the wireless device or change the location then test again
When multiple lights are being used, the functions of the lamps are not synchronized| The distance between the light fixtures is too far| Use separate remote controls, or try removing obstructions can also affect signal transmission
Signal reception is out of sync| With multiple lights, the signal
reception may have a slight delay (the time difference is less than 1 second)

BATTERY HANDLING AND USAGE

WARNING:
Keep batteries away from children and pets.

• Follow the battery manufacturer’s safety and usage instructions.
• Insert the battery observing the proper polarity (+/-) as indicated inside the battery compartment.

CAUTION:
Failure to properly align the battery polarity can cause personal injury and/or property damage.

• Remove a spent or discharged battery from the product. Remove the battery when not using the product for an extended period.
• Never throw batteries into a fire. Do not expose batteries to fire or other heat sources.

DISPOSAL OF USED BATTERIES:
Battery may contain hazardous substances which could endanger the environment and human health. Used batteries shall not be treated as municipal waste, but left at the appropriate collection point for recycling. For more information about collection and recycling of used batteries, please contact your local municipality or waste disposal service.

• Use type CR2032 batteries.
• Install only new batteries of the same type in your product.
• Failure to insert batteries in the correct polarity, as indicated in the battery compartment, may shorten the life of the batteries or cause batteries to leak.
• Do not mix old and new batteries.
• Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or (Nickel Metal Hydride) batteries.
• Danger of explosion if battery is incorrectly replaced.
• Batteries should be recycled or disposed of as per state and local guidelines.

Since 1932, Globe has taken pride in offering products of the
highest quality, and a level of service unparalleled in the industry.
Should you encounter any difficulties, have any questions or
simply wish to offer us your valuable feedback, you may
contact us in the following ways:
Toll Free Telephone: 1-888-543-1388 (North America Only) /
Toll Free Fax: 1-800-668-4562 (North America Only)
E-Mail: info@globe-electric.com / Mail: Globe Electric
Customer Service Department
150 Oneida, Montreal, Quebec, Canada H9R 1A8
Please visit our website to discover other quality Globe
products: http://www.globe-electric.com

References

• Electric | The Largest Consumer Energy & Renewables Platform

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>