SEALEY CST983HD Heavy Duty Sack Truck with PU Tyres Instruction Manual
- June 13, 2024
- SEALEY
Table of Contents
SEALEY CST983HD Heavy Duty Sack Truck with PU Tyres Instruction Manual
HEAVY-DUTY SACK TRUCK WITH PU TYRES MODEL NOS: CST983HD, CST986HD, CST987HD
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instructions
Wear safety footwear
SAFETY
- 9 Always load evenly with the centre of gravity of the load as near the centre and rear of the plate as possible.
- Obtain additional support for large or wide loads to prevent tipping.
- DO NOT overload the truck – see Specification.
- DO NOT leave unattended, especially when loaded, unless the wheels are chocked or the truck is otherwise secured.
- DO NOT use truck on uneven ground and do not run over curbs or steps – use a ramp.
- DO NOT allow others to ride on the truck.
- DO NOT use the truck if any part is damaged, paying particular attention to the wheels.
INTRODUCTION
Heavy-duty tubular steel construction with welded joints with a 200/250kg capacity. Puncture proof heavy-duty PU tyres with powder coated steel hubs and fitted with knuckle protecting D-shaped handle grips.
SPECIFICATION
| Model No | CST983HD | CST986HD | CST987HD |
|---|---|---|---|
| Capacity | 200kg | 250kg | 250kg |
| Height(s) | 1150mm | 1150mm | 1220mm |
| Overall Width | 470mm | 525mm | 540mm |
| Platform Depth | 220mm | 180mm | 250mm |
| Wheel Bore Size | Ø16mm | Ø16mm | Ø16mm |
| Wheel Size | Ø210mm | Ø250mm | Ø250mm |
| Wheel Width | 55mm | 85mm | 85mm |
ASSEMBLY
WHEELS
- Ensure axle is clean from dust and dirt to allow free movement of the wheel.
- For Model No. CST987HD the axle (fig.1.1) needs to be put through the frame before the wheels can be attached.
- Slide the wheel (fig.1.2) onto the axle, put on the washer (fig.1.3) and complete by pushing the split pin (fig.1.4) through the hole in the end of the axle and bending over to retain.
- Repeat for the other side.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
REGISTER YOUR PURCHASE HERE
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 3 years from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 [email protected] www.sealey.co.uk
© Jack Sealey Limited Original Language Version
CST983HD, CST986HD, CST987HD Issue 2 (H,2,F) 08/06/23
