TARAMPS PRO 2.4D Digital Audio Processor Instruction Manual

TARAMPS PRO 2.4D Digital Audio Processor

Specifications

• Product Name: PRO 2.4D Processor
• Manufacturer: Taramps Electronics Ltda
• Country of Origin: Brazil
• Compliance: Directive 2014/30/EU

Product Information

The PRO 2.4D Processor by Taramps is a high-quality audio processing unit designed for aftermarket electronic equipment in vehicles. It features a compact design with various input and output options, including RCA signals input, power supply connectors, LED indicators for limiter and clip, and more.

Product Usage Instructions

Before using the processor, read the manual thoroughly to understand the safety precautions and key recommendations. Pay attention to safety symbols and cautions to prevent injury or product damage.

• When turning on the processor for the first time, select the desired language using the rotary encoder.
• Adjust the master volume by turning the encoder knob clockwise or counterclockwise.
• Use the output selection keys to adjust individual gains for outputs 1 to 4.
• A quick touch on the output key performs an adjustment of the individual gain.
• A long press on the output key mutes the individual sound; press again to unmute.

For detailed technical assistance and warranty information, visit the manufacturer’s website or contact the factory support directly using the provided phone numbers and email addresses.

FAQ

• Q: Can I install the PRO 2.4D Processor myself?
• A: The installation of this product must be done by a qualified professional to ensure proper setup and functionality.
• Q: How do I adjust the output levels?
• A: Use the output selection keys to adjust individual gains for each output channel (1 to 4). A quick touch on the key performs an adjustment, and a long press mutes/unmutes the sound.

Term of warranty

TARAMPS, located on Julio Budisk highway, SN, KM 30 – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, warrants this product against any defects on terms of the project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of a defect during the warranty period, TARAMPS’s responsibility is limited to the repairing or replacement of the device of its own making.

This warranty excludes

• Damaged products by improper installation, water infiltration, and violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Cases in which the product is not used in adequate conditions;
• Defects caused by accessories, modifications or features attached to the product;
• The product with damage from falling, bumps or nature-related problems (flooding, lightning, etc);
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

For international support, check on our website:

• www.taramps.com.br/en/rede-de-assistencias-tecnicas or contact direct the factory support:
• Phones: +55 18 3266-4050 / +55 18 99749-3391
• E-mail: service@taramps.com.br

Introduction

• Read this manual before installing the product. In case of questions contact our technical support:

• +55 (18) 3266-4050 or www.taramps.com.br.

• At the end of its lifespan, this product must not be disposed of in household waste.

• Look for an electronic equipment collection or recycling centre for proper disposal.

Safety requirements

To ensure proper use, please read through this manual before using the processor. You must know the CAUTIONS contained here.

• The installation of this product must be done by a qualified professional.
• Use the correct tools for installing this product.
• This product is for use with 12V batteries. Always check the voltage before installing.
• This product must be installed in a firm location and away from heat sources.
• Never install the product in places exposed to dust, humidity and water. Pay attention to installing it far from the fuel tank, fuel lines, heat sources and other parts of the vehicle.
• Be sure to install a protection fuse or a circuit breaker near to battery. Follow the ampere rating as indicated here in this manual. Use of an improper fuse or circuit breaker could result in overheating, smoke, damage to the product, injury or burns.
• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through the car’s body.
• Automotive sound systems may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.

Key recommendations

The wire gauge for power supply connections is 1,5mm. (15 AWG) for positive and negative wires, and 0,50 mm (20 AWG) for remote signal wire.
For protection against overload, install a fuse on a positive wire, close to the battery terminal (1A). See page 12.

1. – Power supply negative: Connect to a negative pole of the battery.
2. – Remote signal input: Connect to the remote signal output from the head unit.
3. – Remote output: For connection in amplifiers
4. – Power supply positive: Connect to the positive pole (12V) of the battery.

Safety

• As you read this manual, pay attention to the safety symbols.

CAUTION

• This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in a risk of injury to user or product damage.

Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units that were previously produced.

Processor Overview

• RCA signals input: Input for low-level/high impedance (RCA) signals.
• WIRE High-Level Input: Input for high-level / low-impedance signals (from the speaker output of the players or multimedia centre).
• It features the function of automatic turn-on by the input signal, so it eliminates the use of the REMOTE-IN wire from the power connector when using this input.
• Note: The system is designed for use in virtually all multimedia head units on the market.
• However, on some head units, you may not get the trigger effect due to the type of audio output circuit. In this case, use the REMOTE wire to trigger it normally.
• Input clip indicator LED: It shows that the signal is reaching the maximum limit of the processor input, which causes signal distortion. If it comes on, reduce the volume of the signal source and readjust the system gains accordingly.
• Limiter/clip LEDs: They have a dual function: They indicate that the signal from that output has reached the maximum level (when the limiter is off) or the actuation of the limiter (when the signal reaches the threshold defined in the limiter).
• Power connector:

Screens & basic operation

INITIAL SETUP: When turned on for the first time, the processor waits for the language to be set. Choose the desired language and confirm with a quick touch in the center of the encoder.

• Turning the encoder knob (clockwise or counterclockwise) adjusts the master volume (Input volume).

Output selection keys

• Quick touch (Click) on the key of each output(1 to 4) It performs an adjustment of the individual gain in each output.

• Individual mute: Press the output key (1 to 4) for 1 second until the key goes out. To unmute the individual sound, press it again for 1 second.

• Quick click on the center of the encoder, to access the MAIN MENU and its functions.

• Long touch (1 second) in the center of the encoder returns to the previous menu, until returning to the main screen.

Menu & parameters navigation

Use the encoder, turning left (decrement) or right (increment). Menu selection, option or parameter change can be done by pressing the centre of the encoder.
Note: In any of the audio adjustment screens, the hotkeys for channels 1 to 4 allow you to check and adjust the parameters of each channel without leaving the desired option
Tip: To fine-tune a parameter or increment/decrement the number after the decimal point, rotate the encoder slowly. E.g., in the signal level (dB) adjustments, the increment will be 0.1dB when turning the encoder slowly, and 1B when turning it more continuously and quickly.

Menu structure & Description

• Press the encoder button (center–long press) to back to Main Screen.

Audio menu: Adjusts and controls related to audio processing:

I/O Routing: Defines the internal connections between outputs and inputs. Available options: A, B or A+B (sum of the two inputs).
E.g.: setting the OUT 1 output to A, its signal will come from input A.

Band equalizer: It has 5 filters of equalization, with attenuation /boost of up to 12dB, adjustable Q factor, 2 octaves, but centre frequencies which can be changed up to 2/3 octave.
Acts simultaneously on inputs A and B.
The Pro 2.4D has 12 preset equalization curves, selectable in MAIN MENU > Presets EQ.

Crossover: Set the high pass (HPF) and low pass (LPF) filters of the selected output way. The cutoff frequencies could be set from 10Hz to 22KHz, and are available some kinds of filters (Butterworth, Bessel, Linkwitz Rilley) in different slopes (-6, -12, -18, -24, -30, -36, -42 e -48dB/ Octave).

Delay: Set the delay to be applied to the audio signal, for systems alignment. The position of the transducer’s voice coil should be taken in account to set the optimal delay value.

• Rotate the rotary encoder to set the delay amount to be applied.

The voice coils of each transducer aren’t aligned inside the acoustic box, so there is some delay that can degrade the perfect audio playing. The Delay feature applies different delay amounts for each output way, to get the perfect audio alignment.

How to set the delay parameter value (centimetre)

1. Set the reference coil (*) farthest from the box panel (in our example, the reference was the centre of the horn coil)
2. Measure the other channels and find the measure A. Set the closest measurement (in cm) for each channel.
3. Repeat the procedure for the other channels (the channel selection can be done through the keys of each channel).

Phase: Allows inverting the phase of the channel output signal, selecting option [180]. Select the channel using the OUT1 to OUT4 selection keys and select the desired phase by turning the encoder.

• Limiter: Acts as a limiter for the maximum signal level of the processor output, so as not to exceed the power limit supported for each system transducer.

Limiter in RMS function

• Limiter that acts with reference to the RMS value of the audio signal, prevents overheating of the speakers due to excessive power.

Limiter parameters

Modes: MANUAL = Manual Attack, Hold and Release adjustment; AUTO: Sets the Attack, Hold and Release parameters automatically, according to the channel frequency cutoff (HPF).

• Threshold – Point when the limiter begins to act (indicated by the RED LED on each lane turning on). To turn off the limiter, turn the encoder clockwise until [OFF] appears in the threshold value.
• Attack, or Attack time – Time needed to limiter reduce the gain after the signal reaches the threshold.
• Hold – Time that the limiter keeps the signal attenuated even after its level drops below the threshold.
• Modes: MANUAL = Manual Attack, Hold and Release adjustment; AUTO: Sets the Attack, Hold and Release parameters automatically, according to the channel frequency cutoff (HPF).
• Limiter: Acts as a limiter for the maximum signal level of the processor output, so as not to exceed the power limit supported for each system transducer.
• Rel e ase, or Release time – Time needed to limiter return to the original gain after the signal drops below the threshold.

According to Threshold selected. The accuracy of this measurement depends on the signal frequency as a function of the Attack time. At low frequencies, very fast attack times can affect measurement accuracy.

Limiter in PEAK function

• Limiter that acts with reference to the PICO value of the audio signal, prevents mechanical damage and overheating of the speakers due to excessive displacement.

Limiter parameters

• Modes: MANUAL = Manual Release adjustment; AUTO: Sets the Release parameter automatically, according to the channel frequency cutoff (HPF).
• Dynamic – Point when the limiter acts (indicated by the lighting of the RED LED on each channel) with reference to the peak value of the signal in relation to the threshold dened in the RMS limiter (Music Dynamics).
• Hold – Time that the limiter keeps the signal attenuated even after its level drops below the threshold (Dynamic).
• Release, or Release time – Time needed to for the limiter to return to the original gain after the signal drops below the threshold.

Output level: Defines the level of each output channel, allowing to apply from -45dB attenuation up to +15dB gain, regardless the main volume. Select the output channel using the selection keys (1 to 4), adjust the gain level by rotating the encoder.

Note: This function has a shortcut: simply pressing the corresponding output key when in the main screen.

Output parametric EQ. : EQ with 1 band and adjustable parameters for:

• G = Filter gain/attenuation (-12dB to +12dB)
• F = Filter central frequency, adjustable from 10Hz to 22KHz
• Q = Filter width adjustment from 0.4 (widest) to 10.0 (narrowest)

• Audio Generator : Sine wave generator, with frequency and variable amplitude. With 4 modes:
• Fixed Frequency : Sine generator with frequency (10Hz to 22KHz) and amplitude (-60dB to 0dB) adjustments. Note that when activating the generator, the signal is sent to all outputs and it is possible to adjust the other functions and parameters in real time, since the generator remains active and defined as a signal source when in the ON position, even when accessing another function.

• The voltage level shown is informative and may differ depending on processing settings (Equalization, cuts, limiter, etc…).

Sweep (Slow / Medium / Fast): It performs a signal sweep, with the initial and final frequency defined by the user, which remains in a continuous cycle (repeating) until the generator is turned OFF. There are 3 sweep speeds avaliable.

• Language: Choose the desired language (Portuguese, English or Spanish)

• Save config: Allows you to choose the memory location and assign a convenient name to these settings. Selecting which memory location, click on the encoder center to switch to the text. Rotate the encoder to select the desired letter, click on the center of the encoder to move to the next character. To erase, rotate the encoder until “<” + quick touch on the center of the encoder. To finish editing and save the memory name, place the cursor after the last character + long press on the center of the encoder and confirm “YES”.

• Load config: Load a previously saved configuration or the factory default setting. Rotate the encoder to select the desired memory, click on the center of the encoder to select and then confirm. Important: when you select the FACTORY SETTINGS option, the previously saved settings will be lost.

• Password / lock: Allows you to lock the processor using a password (the default password is 1234) or change the password to a personalized one, with 4 digits.

NOTE: When locking the processor, a padlock icon will appear in the upper right corner of the screen. A password will be required to access the settings. To reset the processor to factory settings without accessing the menu (e.g. due to lost/forgotten password), just turn on the processor while keeping the keys of ways 1 and 2 and the center of the encoder pressed simultaneously. This will erase the contents of user settings memories and reset the product to initial setup.

Presets EQ: The Pro 2.4D has 12 preset equalizer curves. Select the music style and press the encoder center to apply the equalization curve:

• FLAT
• LOUDNESS
• BASS BOOST
• MID-BASS BOOST
• TREBLE BOOST
• POWERFUL
• ELECTRONIC
• ROCK STYLE
• HIP-HOP STYLE
• POP MUSIC
• VOCAL
• COMPETITION

Text message: Defines a text of up to 15 alphanumeric characters to be displayed as screen saver animation. Enable the function by selecting ON and with a quick touch on the center of the encoder, and go to text editing (blinking cursor). Rotate the encoder to select the desired letter, click the center of the encoder to move to the next character. To erase, turn the encoder until “<” + quick touch on the center of the encoder. To finish editing and save the text, place the cursor after the last character + long press in the center of the encoder. After about 3 seconds of no activity on the main screen, the text will be displayed as an animation on the screen.

Connecting processor inputs & outputs

CAUTION: Check power polarity and recommended gauge. it is recommended to install a 1 Ampere fuse on the positive supply terminal.

Technical features

Processing

• Resolution………………………………………………….24bits
• Sampling rate……………………………………………..48KHz

Inputs and Outputs

• Number of input channels……………………………………………………………………………2
• Number of output channels………………………………………………………………………….4
• Input/output routing:……………………………………………………………………….A, B, A+B
• Master gain adjustment:…………………………………………………………………..-80 a 0dB
• Output gain adjustment:……………………………………………………………….-45 a +15dB
• Input impedance (RCA):…………………………………………………………………..10K ohms
• Input impedance (high level):…………………………………………………………….50 ohms
• Output impedance…:………………………………………………………………………..47 ohms
• Maximum input level (RCA):………………………………………………. 5,9Vpp (2,1V RMS)
• Maximum input level (High level):…………………. …………………….28Vpp (10V RMS)
• Maximum output level:…………………………………………………….. 5,9Vpp (2,1V RMS)
• Frequency response (-1dB)…………………………………………………………10Hz a 22KHz
• Total Harmonic Distortion…………………………………………………………………….0,01%
• Signal / Noise Ratio………………………………………………………………………………>90dB
• Crosstalk (separation between channels)…………………………………………………>80dB

Input graphic equalizer, 5 bands, 2 octave and 12 presets

• Central Frequencies……………………………EQ.1 – 63Hz (adjustable from 40Hz to 100Hz)
  • EQ.2 – 250Hz (adjustable from 160Hz to 400Hz)
  • EQ.3 – 1000Hz (adjustable from 630Hz to 1600Hz)
  • EQ.4 – 4000Hz (adjustable from 2500Hz to 6300Hz)
  • EQ.5 – 16000Hz (adjustable from 10000Hz to 20000Hz)
• Attenuation / Gain:……………………………….-12dB to +12dB
• Q factor adjustment………………………………..0.4 to 10

Crossover (HPF e LPF)

• Cutoff frequency…………………………………variable from 10Hz to 22KH
• Linkwitz Rilley Filters…………………………-12,-18,-24,-30,-36,-42, -48dB/octave
• Butterworth Filters……………………………..-6,-12,-18, -24, -30 -36, -42, -48dB/octave
• Alignment (Delay)……………………………….8,0mS (272cm)
• Phase……………………………………………………0 / 180°

Adjustable Limiter

• Threshold……………………………………….-48 to 0dB (8mV to 2VRMS)
• Attack…………………………………………………0.1mS to 100mS
• Hold…………………………………………………….0 to 2000mS
• Release…………………………………………………..1mS to2000mS

Adjustable PEAK Limiter

• Threshold / Adjustable dynamics………………………3 to 36dB
• Hold………………………………………………………………..0 to 2000mS
• Release……………………………………………………..1mS to 2000mS

Output parametric EQ

• Central Frequency…………………………….variable from 10Hz to 22KHz
• Attenuation / Gain…………………………………..-12dB to +12dB
• Q Factor Adjustment……………………………………0.4 to 10
• MUTE Function………………………………………..Individual at each output

Audio generator (Sine waveform)

• Frequency range………………………………Variable from 10Hz to 22KHz
• Gain……………………………………………..-60 a 0dB (2mV a 2VRMS)
• Modes………………………………………..Fixed Frequency / 3 speed sweep
• Languages………………………………….Portuguese, English and Spanish
• Setting memory positions……………………..Factory default + 3 assignable positions
• Screensaver function………………………Text up to 15 characters
• Access protection………………………….4 password digits (customizable)
• Supply Voltage………………………..9 to 16VDC
• Nominal consumption (12.6V)……………………0.20A
• Dimensions (WxHxD)……………………….198 x 37 x 113mm (7.80″ x 1.46″ x 4.45)
• Weight………………………………………0.45Kg (0.99lb)

CONTACT

Manufactured by:

• TARAMPS ELECTRONICS LTDA
• TAX ID: 11.273.485/0001-03
• Highway: Julio Budisk, SN, KM 30
• Alfredo Marcondes – SP
• Made in Brazil
• www.taramps.com.br
• +55 18 3266-4050

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>