FLASH DJ Series LED Follow Spot Light User Manual

: June 13, 2024
: FLASH

Table of Contents

FLASH DJ Series LED Follow Spot Light
INTRODUCTION
SAFETY INFORMATION
PRODUCT INFORMATION
INSTALLATION
CONNECTION
DMX CHART
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FLASH DJ Series LED Follow Spot Light

WARNING! Use clamp to rig the fixture.
WARNING! When clamping the fixture to a truss or other structure at any other angle than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
WARNING! Position or shade the bar so that the front lens will not be exposed to sunlight or any other strong light source from any angle – even for a few seconds. See Figure 1. The LED FOLLOW SPOT lens can focus the sun’s rays, creating a potential fire hazard and causing damage.
IMPORTANT! Do not point strong light output from other fixtures at the LED FOLLOW SPOT, as intense illumination can damaged the display.

INTRODUCTION

THANK YOU FOR PURCHASING THE LED FOLLOW SPOT. FOR SAFETY REASONS AND TO ENSURE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.

SAFETY INFORMATION

Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
Before operating, ensure that the voltage and frequency of the power supply match the power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Disconnect main power before servicing and maintenance.
Use a safety chain when fixing this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
Maximum ambient temperature is: 40°C Don’t operate it where the temperature is higher than this.
In the event of a serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself.
Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type of spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the light spot while the fixture is on.

PRODUCT INFORMATION

Light Source: 1 LED 150W (White)
Power consumption: 150W
Power supply voltage: 110-240V, 50/60Hz AC
Color Wheel: 5 + White
Operating modes: DMX512, Manual (Keyboard – buttons and sliders)
DMX channel mode: 4
IP Rating: IP20
Housing made: Aluminium
Cooling: Active
AC IN: PowerCon 3-Pin XLR DMX Input/Output
Net Weight: 8,4 kg
Gross weight: 25,6 kg
Net Dimensions: H(34)xW(66)xD(28) cm
Pack Size: H(49+10,5 wheel)xW(49) xD(38) cm

INSTALLATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structu-re to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the we-ight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it. The fixture may be installed in any orientation, but if installed horizontally with a downward beam-angle, water can potentially pool in the fan wells. Under normal operation, the moisture will evaporate. However, in locations with high rainfall, you may wish to fabricate a rain shield above the fixture, or modify the position and orientation of the fixture to minimize pooling. Two quarter-turn brackets are supplied with the fixture if it is to be flown above the ground. Rig the fixture to a support truss or structure using the supplied brackets and suitable clamps. Fasten a safety cable between the support structure and the attachment point on the fixture. The safety cable must be able to bear at least 10 times the weight of the fixture.

The package includes

LED FOLLOW SPOT (1 pc)
Height-adjustable tripod column (1 pc)
Transport case (1 pc)
User Manual (1 pc)

CONNECTION

The device is equipped with the following interfaces:

DMX (in/out): XLR 3(5)-pin socket
Power (in/out): powerCON socket The connection is performed using cable with XLR-female -> XLR-Male plugs.

CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between signal (-) and si-gnal (+) into an XLR plug and plug it in the DMX output of the last fixture. The connection is performed using a power cable with a powerCON connection (included). The device must be operated by qualified personnel.

CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions Using a lamp, the change rate of power voltage should be within ±10%, if the voltage is too high, it will shorten the light’s life.

Voltage Specification.