Englander AC02780 Fireplace Tool Sets Instruction Manual
- June 13, 2024
- ENGLANDER
Table of Contents
Englander AC02780 Fireplace Tool Sets
Product Information
- Product Name: Non-Combustible Mantel Shelve
- Model Numbers: AC02780, AC02781, AC02782, AC02783
- Country of Origin: Canada
- Warranty: One year
Product Usage Instructions
- Kit Contents: Please ensure that all the components listed in the kit are present before starting the installation.
- What You Will Need (not included): Make sure you have the following tools for installation: Powered Driver, Phillips head drive, Tape Measure, Level, and Stud Locator.
- Installation Safety Warnings: Before proceeding with the installation, carefully read and adhere to all the safety warnings provided in the user manual.
- Installation Notes: Familiarize yourself with the installation notes to ensure a successful and safe installation process.
- Installation Instructions: Follow the step-by-step instructions below to install the mantel:
- Step 1: Unpack the mantel from the box and remove any protective foam. Take note of the predrilled mounting holes on the top flange of the mantel.
- Step 2: Locate the mounting bracket and hardware provided inside the box.
- Step 3: Determine the vertical and horizontal center for the top of the mantel on the wall. Mark this location.
- Step 4: After determining the correct height for attaching the mantel, draw a horizontal line. Install the mantel bracket by fastening screws through the provided holes on top of the mantel. Do not screw through the bottom of the mantel. Ensure not to over-tighten the screws.
- Step 5: If required, use non-combustible shims to level the mantel. Install the shims over the studs.
- Step 6: Fill any screw holes on the top surface of the mantel with the provided filler, if necessary.
Note: Please refer to Figure 1, Figure 2, and Figure 3 in the user manual for visual representations of the front mount, side mount, and side mount with mantel installations, respectively.
Important: This product comes with a one-year warranty. For any warranty- related inquiries or concerns, please contact SBI Heating. Thank you for choosing an SBI Heating accessory! Enjoy your new Non-Combustible Mantel Shelve.
Kit Contents
- Mantel (1x)
- Mounting Bracket 3″x 2″ (1x)
- Self-drilling screws for Mantel 2 ¼” (3x)
- Sharp point screws for mounting bracket 2 ½” (8x)
What You Will Need
What You Will Need (not included)
Installation
Installation Safety Warnings
- Read all instructions before mounting or using the mantel.
- Use the mantel only for its intended use as described in these instructions.
- DO NOT OVERLOAD MANTEL: The maximum load for all 60-inch mantels is 150 lbs. The maximum load for all 72-inch mantels is 180lbs.
- Mantel “superfast” material meets noncombustibility standards in accordance with ASTM E136.
- WARNING: Combustible objects placed on or around the mantel must meet your fireplace manufacturer’s requirements for clearances to combustibles.
- IMPORTANT: The fasteners supplied with this furnishing are intended for use in standard wood stud walls or 16 gauge metal stud walls only. The minimum wall stud size required is 2”x 4”, with drywall or finished wall surface ranging from ½” to ¾” thick.
- For all other mounting surfaces, use appropriate fasteners as specified by local building codes or other jurisdictions. For mounting to other wall types; if you are at all unsure of the correct fastening method, contact your local building official. Improper mounting may lead to property damage, injury, or death.
- Be sure to follow your fireplace manufacturer’s clearances to non-combustibles or local code if applicable when determining a location for your mantel. Combustibles set on a non-combustible mantle must meet clearance requirements for combustibles.
- IMPORTANT: If you are at all unsure of the correct fastening method, contact your local building official. Improper mounting may lead to property damage, injury, or death.
Installation Notes
- Recommended two people to lift and install the mantel.
- If you are unable to find studs, you need to open the wall and add wood studs or 16 gauge metal studs if in the non-combustible zone.
- A minimum of 3 studs are required to safely install a 5 ft. mantel. Minimum of 4 studs for 6 ft. mantels. Using 2 1/2” sharp point screws, attach the mounting bracket to studs with two screws per stud. See Figure 1 on page 5 for details.
- If attaching a mounting bracket over a masonry surface use the proper masonry anchor for the type of surface – consult your fastener supplier. The anchor should be able to support 4 times the load.
Installation Instructions
- Step 1. Unpack the mantel from the box. Remove protective foam. Note: the top flange of the mantel has predrilled mounting holes.
- Step 2. Locate the mounting bracket and hardware inside of the box.
- Step 3. Determine the vertical and horizontal center for the top of the mantel on the wall. Mark this location.
- Step 4. After identifying the correct height for attaching the mantel, draw a horizontal line. Install a centered mounting bracket (with the 2″ side on the wall) with 2 sharp point screws per stud. Use 1/8” drill bit to drill holes in the mounting bracket. You will need two people to place the mantel on the bracket and check for level, take the mantel off, and stabilize the mounting bracket with remaining screws. See Figure 2.
- Step 5. With two people, lift the mantel and place it over the mounting bracket. When centered and flush against the wall, place one 2 1/4” self-drilling screw in the center pre-drilled hole on top of the mantel. Screw through the mounting angle until the fastener head is flush with the countersunk hole. See Figure 3
- DO NOT OVER-TIGHTEN.
- Fasten screws through the provided holes on top of the mantel.
- DO NOT SCREW THROUGH THE BOTTOM OF THE MANTEL
- Step 6. Shims may be required to level the mantel. Install non-combustible shims over the studs. If required, fill screw holes on the top surface of the mantel with the provided filler.
ONE YEAR WARRANTY
SBI Heating Accessories warrants for the purchaser’s first year of ownership that our noncombustible mantle, when reasonably maintained and used, shall be free from any defects in material; or manufacturer’s workmanship. Proof of purchase will be required, so keep your receipt. A Return Authorization Number is needed to return goods prepaid to our facility, at 250 rue de Copenhague Saint-Augustin-de-Desmaures, Québec, Canada, G3A 2H3. SBIHA shall not be liable for any consequential or identical damages resulting in loss from the use of this product. In no case will SBIHA’s liability exceed the customer’s purchase cost. Thank you for purchasing an SBI Heating accessory!
MODELS
- AC02780,
- AC02781,
- AC02782,
- AC02783
CONTACT
- SBI HEATING ACCESSORIES
- 25 De Copenhague Street
- Saint-Augustin-de-Desmaures
- Québec, Canada
- G3A 2H3
- 1-877-356-6663
Read User Manual Online (PDF format)
Loading......