eurolite PST-9W TCL FB Spot User Manual

eurolite PST-9W TCL FB Spot

INTRODUCTION

Welcome to Eurolite! Thank you for choosing one of our products. Eurolite is your connection to the world of show with an unparalleled variety of products, both for professionals and beginners.

If you follow the instructions given in this manual, we are sure that you will enjoy this product for a long period of time. This user manual will show you how to install, set up and operate your new Eurolite product.

Users of this product are recommended to carefully read all warnings in order to protect yourself and others from damage. Please keep this manual for future needs and pass it on to further owners.

Product descriptions LED pin spot by Eurolite brings sharp RGB beams in every window display, party room or trade fair! Light up the room in any color you like to impress your audience.

The PST-9W is operated via the supplied remote control which is not bigger than a credit card and fits in even the smallest pocket. You wish to illuminate a larger area? No problem! Simply use common 3.5 mm jacks to link multiple pin spots to create impressive light effects.

For a permanent installation you can simply use the pre-punched holes on the fixture. As the pin spot is delivered ready to use, all you have to do is install it and switch it on – plug and power cord are included. Once you plugged in the  PST-9W, you can use preset programs like slowly fading colors, rapid color changes or constant light in a single color. Brightness can be manually adjusted as well. It’s entirely up to you to make the most of your event!

Product features

• Compact LED projector for illuminating mirror balls, and for decorating display windows and party rooms
• 1 bright RGB LED
• IR remote control in credit card format included in delivery
• Serial connection of multiple pinspots via included link cable
• Built-in programs for color change, color fade and strobe effect
• Adjustable program speed and brightness
• Direct color selection for 16 preset colors
• Memory function
• Mounting bracket for ceiling or wall mounting
• Low power consumption

Package contents

• Spotlight
• these instructions

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

Please read the safety warnings carefully and only use the product as describe in this manual to avoid accidental injury or damage.

Intended use

• This device is a spotlight for creating decorative lighting effects. It is only suitable for decoration and not for household lighting. The product is fitted with LEDs that consume little power, have an extremely long service life and develop little heat. The product is designed for private use and is not intended for commercial use.
• Only use the device according to the instructions given herein. Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage.
• We do not assume any liability for material and personal damage caused by improper use or non-compliance with the safety instructions. In such cases, the warranty will be null and void.
• Unauthorized rebuilds or modifications of the device are not permitted for reasons of safety and render the warranty invalid.

Danger due to electricity

• The device is suitable for indoor use only. Do not use it outdoors. Never expose it to rain or moisture. Do not store it in rooms exposed to moisture.
• To reduce the risk of electric shock, do not open any part of the device. There are no serviceable parts inside the device.
• Only connect the device to a properly installed mains outlet. The outlet must be protected by residual current breaker (RCD). The voltage and frequency must exactly be the same as stated on the device. If the mains cable is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a mains cable. Failure to do so could possibly injure the user.
• The mains outlet must be easily accessible so that you can unplug the device quickly if need be.
• Never touch the mains plug with wet or damp hands. There is the risk of potentially fatal electric shock.
• The mains cable must not be bent or squeezed. Keep it away from hot surfaces or sharp edges.
• Never pull the mains cable to disconnect the mains plug from the mains outlet, always seize the plug.
• Unplug the device during lightning storms, when unused for long periods of time or before cleaning.
• Do not expose the device to any high temperatures, direct sunlight, dripping or splashing water, strong vibrations or heavy mechanical stress. The recommended temperature range is -5 to +45 °C.
• Do not place any objects filled with liquids on the device.
• Do not place any open sources of fire, such as burning candles, on or directly next to the device.
• Make sure that objects cannot fall into the device, in particular metal parts.
• Only have repairs to the device or its mains cable carried out by qualified service personnel. Repairs are required when the device or the mains cable is visibly damaged, liquid has been spilled or objects have fallen into the device; when the device has been exposed to rain or moisture, has been dropped or malfunctions occur.
• Cleaning of the device is limited to the surface. Make sure that moisture does not come into contact with any areas of the terminal connections or mains voltage control parts. Only wipe off the product with a soft lint-free and moistened cloth. Never use solvents or aggressive detergents.

Danger to children and people with restricted abilities

• This product is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around carelessly. Never leave this device running unattended.
• This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.

Warning – risk of burns and injuries

• Do not use the device near highly flammable materials. Always place the device at a location where sufficient air circulation is ensured. Leave 50 cm of free space around the device. Never cover the air vents of the housing.
• Do not look directly at the light source. Persons with light-sensitive epilepsy may suffer from epileptic seizures or fall unconscious.
• Make sure that the product is set up or installed safely and expertly and prevented from falling down. For commercial use the country-specific accident prevention regulations of the government safety organization for electrical facilities must be complied with at all times.

Caution – material damage

• This device must not be connected to the mains voltage by means of a dimmer.
• Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
• Never switch the device on and off in short intervals. This will considerably reduce the service life of the device.
• If the device has been exposed to drastic temperature fluctuation, do not switch it on immediately. The resulting condensation may destroy the device. Allow the device to reach room temperature before connecting it. Wait until the condensation has evaporated.
• Please use the original packaging to protect the device against vibration, dust and moisture during transportation or storage.
• If a serial number label is affixed to the device, do not remove the label as this would make the warranty void.

CLEANING AND MAINTENANCE

The product is maintenance-free, except for occasional cleaning. You can use a lint-free, slightly dampened cloth for cleaning. Disconnect the product from power before cleaning. Refer all servicing to qualified personnel. The LEDs are permanently installed; they cannot be replaced.

PROTECTING THE ENVIRONMENT

Disposal of old equipment
When to be definitively put out of operation, take the product to a local recycling plant for a disposal which is not harmful to the environment. Devices marked with this symbol must not be disposed of as household waste. Contact your retailer or local authorities for more information. Remove any inserted batteries and dispose of them separately from the product.

You as the end user are required by law (Battery Ordinance) to return all used batteries/ rechargeable batteries. Disposing of them in the household waste is prohibited. You may return your used batteries free of charge to collection points in your municipality and anywhere where batteries/rechargeable batteries are sold. By disposing of used devices and batteries correctly, you contribute to the protection of the environment.

OPERATING ELEMENTS AND CONNECTIONS

1. RGB LED
2. Mounting bracket
3. Fixation screw
4. 3.5mm jack connector to link multiple devices
5. Power cord
   

SETUP

Placing the unit

Fasten the device to a wall or ceiling with the mounting bracket. Always choose screws and plugs which are suitable for use in your wall/ceiling and have enough holding power. Fasten the device in such way that it will not fall down.

Connection to the mains

The device uses an auto-range power supply that accepts input voltages between 100 und 240 volts. Connect the device via the mains cable to a grounded mains socket. Thus the unit is switched on. To switch off the unit, disconnect the power plug. Notes: Do not connect the unit to the mains voltage via a dimmer. For a more convenient operation, use a mains outlet which is switchable.

Linking several devices

Several spots may be interconnected via the IN and OUT jacks, connection cables are included. Then all units can be synchronized and controlled with one remote control.

Connection of the IR receiver

Connect the IR receiver to the IN jack of the first unit in series.

OPERATION

After connecting the unit to the mains it is ready for operation. The spot is to be controlled via IR-13 remote control. When actuating a button, always point the remote control in the direction of the sensor at the control unit’s front or rear. A direct line of sight between the remote control and the sensor is required.

Switching the LEDs on and off

The LEDs can be switched on with the button ON and switched off with the button OFF. However, the spot remains switched on. After switching on, the LEDs light up according to the last control program selected.

Constant lighting in one color

For constant lighting of all LEDs in one color, press the corresponding color button. Use the buttons in the upper left corner to adjust the brightness.

Control programs

The control programs can be selected with the respective buttons FLASH, STROBE, FADE and SMOOTH. Running speed is set to the maximum value when a control program is selected. The speed can be adjusted with the buttons in the upper left corner.

Notes:

• The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts prevents the battery from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the remote control. Otherwise operation of the remote control is not possible.

• If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote control press the small bar with the groove to the right and at the same time remove the battery support. For operation, one 3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of the button cell shows upwards in the support.
  

• Remove the battery from the remote control as a precaution if the device is not used for a longer period of time.

TECHNICAL SPECIFICATIONS

All information is subject to change without prior notice. © 20.03.2020

Accessories

D00128947, version 1.3, publ. 20/03/2020 For product updates, documentation, software and support please visit www.eurolite.de. You can find the latest version of this user manual in the product’s download section. © 2020 Eurolite. All rights reserved.
No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design, and manufacturing. Eurolite shall have no liability for any error or damage of any kind resulting from the use of this document.
All trademarks mentioned herein are the property of their respective owners.

Experience Eurolite.
Product videos, suitable accessories, firmware and software updates, documentation and the latest news about the brand. You will find this and much more on our website. You are also welcome to visit our YouTube channel and find us on Facebook.

Customer Service

 www.youtube.com/eurolitevideo
www.facebook.com/Eurolitefans

Eurolite is a brand of Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5 97297 Waldbüttelbrunn Germany D00128947 Version 1.3 Publ. 20/03/2020

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>