TREND NETWORKS R240-QIP Fibermaster Basic Fibre Optic Testing Kit User Guide

TREND NETWORKS R240-QIP Fibermaster Basic Fibre Optic Testing Kit

FiberMASTER OTDR

• The TREND FiberMASTER range provides powerful performance in a small package. A simplified user interface is easy for beginners yet has full manual and custom setups for experienced users.
• Tier 2 OTDR certification fast and accurate with instant-on, zero boot times and selections for TIA/ISO/IEEE/CENELEC standards to eliminate setup errors.
• Match a light source with an OTDR to perform end-to-end testing on multimode or single-mode cable using the included power meter.
• The PON OTDR features ultra-high dynamic range to measure 1:32 splitters for installation testing and troubleshooting.

Getting started with the FiberMASTER

Press and hold the power button for one second to power on the FiberMASTER. The home screen will be displayed and the icons will show available functions, battery level and if a VFL is available. It also allows access to the device setup screen and information about the device through the information icon .
There are one or two available OTDR ports. Dual Wave OTDRs will have one port, Quad Wave OTDRs will have a SM and a MM port (2 ports) and the PON OTDR will have a 1310/1550nm port and an active 1625nm port (2 ports). Determine the appropriate port and connect the fiber under test.

Serial Number

Setting Test Parameters
Once in the OTDR function the OTDR Setup screen will be displayed.

Setup OTDR Screens

The Setup OTDR Screens walk through the basic setup for auto mode testing and manual mode testing. The left/previous arrow, returns to the previous page and the right/next arrow, advances to the next page. The check box in the bottom middle returns to the main OTDR Setup page.

• Use these check boxes to set the launch or tail cable on or off. Select the edit icons to input the length of the launch and tail cables as appropriate. These may also be set to auto, in which case the OTDR will establish the first event as the end of the launch  cable and the second to last event (the event before the end event) as the beginning of the tail cable.
• Select one or both wavelengths in either multimode or single-mode.
• Set the Refractive Index if known. Select Load Default if the index of refraction (IOR) and/or helix factor are unknown. Set the End Of Fiber (EOF) Detection Threshold.
• Enough information has now been entered to conduct an Auto Test. If Auto is selected, the averaging time, range and pulse width will be automatically set based on analysis conducted by the  OTDR. Select Manual and those parameters automatically set in Auto Mode will be available for adjustment.

For the purposes of this quick start guide please select Auto followed by the check box at the bottom of the screen.

Setting Limits for Pass/Fail

Standard Limits are pre-set limits/thresholds against which the traces are measured for pass/fail analysis to certify network links.

• Standard limits will be highlighted, There are 5 pages of pre-set limits/thresholds to which the test will be measured to determine Pass/Fail. The first page lists cabling standards and pages 2-5 lists application standards.  Manual allows for setting user defined Pass/Fail thresholds
• If a standard set of limits is selected, when the check box at the bottom of the display is touched, a page confirming those standards will be shown, such as this sample page.

Manual limits may be selected on the OTDR Limits page. The following two pages of limits will be displayed to set limits/thresholds.

Once all settings have been established, touch the check mark at the bottom of the page.
Load Defaults sets the default lim-it values that would be industry standard for each measured item.

Note: The Limits and test thresholds will be displayed for review prior to taking a test.

Conducting a Test

Take a trace by selecting the Test button on the OTDR Setup screen. Once the Test button is selected, the Test Parameter screen below will be displayed. This screen displays the limits/thresholds that have been selected for pass/fail analysis and the parameters set for the trace.

If the settings are correct, select the check box to start the test. A scanning status bar will be displayed, followed by a finding event message.

OTDR Schematic Screen will be displayed once the test is complete.
OTDR Trace Screen use Trace Display icon to cycle to the trace screen view .
OTDR Map Screen use Trace Display icon to cycle to the view.
Event Table

Getting started with the Video Inspection Scope

To operate the video scope, touch the Scope icon on the Home Screen.

Place the proper tip on VIP

To remove a tip from the probe, grasp the probe tip and unscrew the tip retention nut. As oriented in the picture; rotate left to loosen and right to tighten the retention nut on the probe tip. Pull the tip straight up from the probe. To place a tip on the probe, ensure the lens is clean, slide the tip on to the end of the probe and tighten the tip retention nut. Do not over tighten the retention nut.

Video Scope Screen
View Connector and Auto Test

• With appropriate universal tip installed, insert connector into tip.
• Hold connector into the probe tip and rotate focus ring until image is sharp.
• Once focused touch the center of connector to snap it to the center of the screen.
• Set Pass/Fail Icon to Auto.
• Select the Live/Pause icon and allow unit to perform test.
• The result will be displayed in the bottom right of the displayed.

Getting started with Loss Test Set

From the Home Screen select the PM/LS icon to open the Loss Test Set.

Power Meter/Light Source Screen
Power Meter/Light Source Connections
Basic Single Cord PM/LS Operation

Touch the Source indicator to show the light source wavelengths available and select the desired wavelength for the test. Allow the light source 2-3 minutes to warm up and stabilize.
Touch the Modulation indicator to open the modulation options and set the modulation to CW for continuous wave.
Touch the Power Meter indicator to show the power meter wavelengths available and select the appropriate wavelength for the test.

Note: This step may be skipped as the power meter will set itself to the appropriate wavelength, if it is being used with a compatible source.
Plug one end of a reference cord into the light source and the other end into the power meter as shown below.

Touch reference indicator in the bottom right of the display and select, Set Reference to zero out the reference cord.

Disconnect the fiber from the PM port and connect it to a mating sleeve, and connect the cable/cord under test between the mating sleeve and the power meter port, as shown below.

The value in dB, in the center of the display is the loss of the cable under test.

Note: This Example shows two OTDRs with PM and using the optical ports as CW sources for the light source. When using stand alone PM and LS, the PM will only have a single power meter port and the light source will have one or two ports depending on whether it is a dual or quad wave light source.

References

• TREND Networks - Data Cable Testers, Certifiers & Verifiers. CCTV & PoE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>