eta ZERO 2 in 1 Robot Vacuum Cleaner User Manual

2 in 1 Robot Vacuum Cleaner
User Manual

Dear customer, thank you for purchasing our product. Please read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt, and, if possible, the box with the internal packing.

GENERAL SAFETY INSTRUCTIONS

• Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.

• Check whether the data on the type label corresponds with the voltage in an electric socket.

• Never use the appliance if its power cord or adaptor is damaged, if it does not work properly if it fell down and was damaged.
  In this case, take the appliance to a special service to check its safety and proper function.

• The product is intended for home use and similar (in shops, offices, and similar workplaces, in hotels, motels, and other residential environments, and in facilities providing accommodation with breakfast). It is not intended for commercial use!

• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Before replacing accessories or accessible parts, which move during the operation, before assembly and disassembly, and before cleaning or maintenance, turn off the appliance!

• If the power cord of the adaptor is corrupted, it has to be replaced by the manufacturer, its service technician, or a similarly qualified person so as to prevent dangerous situations.

• Never use the appliance if its adaptor or plug is damaged, if it does not work properly, if it fell down and was damaged or if it fell into the water.
  In this case, take the appliance to a special service to check its safety and proper function.

• In order to ensure the safety and proper function of the appliance, use only original spare parts and accessories approved by the manufacturer.

• If the adaptor of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician, or a similarly qualified person so as to prevent dangerous situations.

• WARNING: To charge the battery, use only the network adapter supplied with this appliance.

• To power the appliance, only apply a safe small voltage in accordance with the type plate.

• Never immerse the vacuum cleaner into water (even its parts)!

• Never vacuum without a properly inserted filtration system and micro-filters.

• Do not vacuum sharp objects (e.g. glass, shatter), hot, flammable, explosive items (e.g. ash, hot cigarette butts, gasoline, thinners, and aerosol vapors) or greases (e.g. fats, oils), caustic agents (e.g. acids, solvents). Vacuuming these objects may lead to damage to the dust filters or the vacuum cleaner.

• Pores of the filters may be clogged when vacuum cleaning very fine dust (e.g. fine sand, cement dust, plaster). Thus, air permeability will be reduced and the suction performance will drop. In this case, clean the filters even though the dust container is not full yet.

• Always switch off the vacuum cleaner first and disconnect the power cord from the power supply and only then empty the dust container, clean/replace micro-filters, and clean the vacuum cleaner or its accessories.

• Never leave the vacuum cleaner exposed to weather conditions (rain, frost, direct sun radiation, etc.).

• Never use the appliance for any other purpose than for the intended purpose described in these instructions for use!

• Disconnect the appliance from the mains when not in use for a long period.

• The robot vacuum can go over threshold strips up to 2 cm in height.

• This device can not be used on a carpet whose pile length is over 1 cm.

• Make precautions to solve the problem which may make the cleaning in trouble, such as:
  • Keep the easily knocked over objects in a safe place.
  • Permian the edge of the carpet.
  • The hanging table cloth and curtain should not touch the ground.
  • The flammable object should be cut from the fire source.
  • Sort out the tangled power cord on the floor.
  • Pick up the newspaper, book, magazine, and large piece of paper scattered on the floor.

• Examine if the dustbin is empty and ensure it is fixed before it works.

• See if the up-ground height sensors are wiped clean.

• If you only need to clean one room, please close the door.

• If the room which needs to be cleaned wants a partition, you can place the virtual wall, at the same time, check the facing opening width.

• Please be aware that the device needs 8 cm of clearance underneath furniture so that it will not become trapped.

• Do NOT drop the Robot, should this happen, run the Robot to see that everything is okay before letting it operate by itself without you being present.

• If the battery is leaking, remove it immediately; it can damage the vacuum cleaner.

• Keep batteries out of reach of children and incapacitated people. A person, who would swallow the batteries, must seek medical help immediately.

• Dispose of a discharged battery in a suitable way.

• Never use the appliance for any other purpose than for the intended one described in these instructions for use! This appliance is not intended for outdoor use.

• The manufacturer is not responsible for damage caused by improper use of the appliance and the accessories and their guarantee for the appliance does not apply in situations when the safety warnings above are not complied with. Failure to replace or maintain all filters regularly and also using non-original filters, the properties of which resulted in failure or damage to the vacuum cleaner are also understood to be improper use of the appliance.

| No one else can disassemble maintain or. Transform the product except the maintenance technicians designated by our company or it may cause fire electric shock or personal injury.| | Don’t use another charger but the equipped one of the Robot, or it may cause product damage, electric shock, or fire due to high voltage.
---|---|---|---
| Don’t touch the high-voltage power cord of the electric appliance with your wet hand, or it may cause an electric shock.| | Don’t bend the power cord overly or place weight on it, or it may cause power cord damage, fire, or electric shock.
| Don’t use the Cleaner in commercial places, or the Cleaner may be damaged by excessive use.| | Don’t approach cigarettes, lighter, matches, and other heat objects or combustible materials such as the gasoline cleaner.
| Check whether the adapter and connector are connected well, or it may cause charging failure or even fire.| ****| Insert the power cord of the charger well or it may cause electric shock, short circuit, smoking, or fire.
| Please use the Cleaner cautiously in the presence of the children to avoid frightening or harming them.| | Remove all easily damaged objects (including luminous objects, fabrics, glass bottles, etc.) before using, or it may cause damage to these objects or affect the using of the cleaner.
| Don’t make the Cleaner take
in water and other liquors for fear of product damage.| | Don’t stand or sit on the Cleaner, or it may cause damage to the Cleaner or personal injury.
| Don’t use the Cleaner outdoors,
or it may cause product damage.| | Don’t use the Cleaner on small tables and chairs or other small spaces, otherwise, the Cleaner may be damaged.

APPLICABILITY

The product, mainly applicable to homes, hotel rooms, and small offices, is good for cleaning various short-haired carpets, wood floors, hard floors, ceramic tiles, etc.
Since the vacuum cleaner moves freely in the space of your home, it is necessary to adapt the environment to this fact. Before use, remove all unwanted objects (stretched cables,
scattered clothes, papers, bags, etc.) from the floor that could impede the movement of the vacuum cleaner or, conversely, fragile objects (e.g. glass and ceramic vases) that could be damaged by the vacuum cleaner.

PRODUCT COMPONENTS

3.1 PACKAGE CONTENTS

3.2 ROBOTIC VACUUM CLEANER

A – Robotic vacuum cleaner
A1 – Front bumper
A2 – Sensors against falling downstairs
A3 – Charging contacts
A4 – Storage battery compartment cover
A5 – Drive Wheels (Left / Right)
A6 – Front wheel
A7 – Side brushes
A8 – Upper flip cover
A9 – Main switch
B – Dirt hopper
C – Control panel
H – Cleaning tool

3.3 DUSTBIN

B – Dirt hopper
B1 – Handle
B2 – Dirt container lid
B3 – HEPA filter
B4 – Folding bottom
B5 – Folding bottom lock button
B6 – Separator
B7 – Plastic covering elements
H – Cleaning tool

3.4 CONTROL PANEL

C – Control panel
C1 – START / AUTO (automatic cleaning mode) / STOP (PAUSE) button
C2 – Time setting button
C3 – Battery charging button
C4 –SPOT button (local cleaning)
C5 – Display

3.5 CHARGER STATION

D – Charger station
D1 – Operation indicator
D2 – Charging contacts
D3 – Adapter connection port

3.6 REMOTE CONTROL

F – Remote control
F1 – F1 – START / AUTO (automatic cleaning) / STOP (PAUSE) button
F2 – Directional buttons for manual control (FORWARD /BACKWARDS / RIGHT/ LEFT)
F3 – Button for setting the suction power level
F4 – SPOT button (local cleaning)
F5 – Button for return to charging station
F6 – AUTO button (current cleaning)
F7 – Robot Vacuum Localisation button
F8 – EDGE button (cleaning along the walls)

3.7 MOP EXTENSION

G – Mop extension
G1 – Mop unit lock button
G2 – Rubber stopper
G3 – Mop

3.8 SPARE PARTS LIST
Spare brush set: side brushes (left, right) + HEPA filter: ETA122700060
Mop: ETA122700200
HEPA filter: ETA122700230

PREPARATION FOR USE

Remove all packing material, and remove the vacuum cleaners and accessories.
Remove any adhesive, stickers, or paper from the vacuum cleaner.

4.1 VACUUM CLEANER PREPARATION
Install dirt container B and mop unit G (depending on robot vacuum use). Install side brushes A7.

4.2 CHARGER STATION INSTALLATION

1. Place the charging station on the floor. Make sure there is enough space on the sides of the base (at least 1 m) and in front of the base (at least 2 m). Don´t expose the charging dock to sunshine.
2. Connect the adapter to the charging station and then to the wall outlet. (the indicator lights up D1).

VACCUM CLEANER USE

Insert the battery into the remote control, and observe the correct polarity (2 pieces, battery type AAA).

5.1 SWITCHING ON THE VACUUM CLEANER

1. Open top cover A8 and switch on the device using A9 (position “I” = on, position “0” = off).
2. An acoustic signal will be given and display C5 will light up. Then the set time will be displayed.

5.2 BATTERY CHARGING

1. Check that the charging station is properly connected to the mains. (light D1 must be on).
2. Position the device near the charging dock and press the C3 button on the device or F5 on the remote control. If the battery is too low, place directly and correctly the vacuum cleaner on the charging station.

Remarks

• The standard charging time is approx. 4-6 hours. A fully charged battery will work for approx. 150 minutes, depending on set functions.
• The stated operating times are based on ETA‘s internal testing and only apply to a new and fully charged battery. Depending on the age and wear of the battery, the operating time decreases.
• During the charging process, increasing “I I I I” bar signs will be displayed on C5.
  After completion of the charging process, a “FULL” message will be displayed. The device goes into sleeping mode.

5.3 START / STANDBY MODE / SLEEPING MODE
Start (Cleaning)
Press C1/C4 on the control panel or the F1/F2/F4/F6/F8 buttons to start the device.
Standby mode (Pause)
Press the C1 button on the control panel or the F1 button on the remote control to interrupt the ongoing cleaning and put the vacuum cleaner in standby mode.
Sleeping mode
After approx. 10 seconds of inactivity, the device will automatically go to sleep mode.
The sleeping mode can also be activated by long (approx. 3 seconds) pressing C1.
Press C1 on the control panel or F1 on the remote control box to return to standby mode.

5.4 CLEANING MODES AND ROBOT VACUUM FUNCTIONS
Manual operation
You can operate the device manually using the F2 direction buttons and clean only the areas where cleaning is necessary.
Smart automatic cleaning (AUTO)
Press the C1 button on the control panel or the F1/F6 button on the remote control. “AUTO” message will be displayed. The robot vacuum will move on the floor until battery capacity has dropped below a defined level. Then the device will automatically go to the charging dock. This is the most used method of cleaning.

Local cleaning (SPOT)
Press the C4 button on the control panel or the F4 button on the remote control. This type of cleaning can only be activated, if the robot vacuum is not in the charging dock. A “SPOT” message will be displayed. When cleaning, the vacuum cleaner moves in the space according to the programmed route (spiral). When cleaning is complete, the vacuum cleaner stops and goes into standby mode. This cleaning mode is suitable for cleaning a small soiled area.

Cleaning along the walls (EDGE)
Press F8 on the remote control. This cleaning function can only be activated, if the robot vacuum is not in the charging dock. ” ” will be displayed. In this case, the robot vacuum will be cleaning preferably the floor surface along the walls (or, as the case may be, along large objects, e.g. settees, cabinets, etc.). When the cleaning has been completed, the device will return to the charging dock. This cleaning mode is intended for removal of dust and dirt accumulated along the walls and in the corners of the rooms.

Note
During the cleaning process, the vacuum cleaner cannot reach the surrounding area of the charging station.

Suction power level setting
Press F3 to switch over high or low suction capacity.
Return to the charging station
In the automatic mode or when cleaning along the walls, the robot vacuum will automatically return to the charging dock after completion of the cleaning. The “BASE” message will be displayed. You can also send the device to the charging dock by pressing  C3 on the control panel or F5 on the remote control.

Current time setting
Press and hold (for approx. 3 seconds) C2 on the control panel in the standby mode (acoustic signal will be given). A box for setting hours/minutes starts flashing on the display. You can switch over minutes and hours by short pressing C2. Use C3 and C4buttons to set the current time. Press C1 to confirm the setting.

How to set a cleaning schedule
At first, set the current time (see above). Then press C2 on the control panel in standby mode. The minute/hour setting box starts flashing on the display. You can switch over the minute or hour setting function by pressing C2. Use C3 and C4 buttons to set the required cleaning time. Press C1 to confirm the setting The device will perform the cleaning in the preset time (AUTO – automatic cleaning).

Delete scheduled cleaning
Scheduled cleaning can be deactivated by:

1. Switch off the robot vacuum by pressing the A9 main switch button.
2. Resetting scheduled cleaning operation (set “00:00” on the display).

5.5 USING THE MOPING ATTACHMENT

1. Attach the G3 mop to the lower part of the moping attachment correctly. Soak and wring the mop before use.
2. Open the rubber stopper G2 and fill the mop attachment with water.
3. Place the mop attachment in place in the vacuum cleaner.
4. Switch on automatic cleaning mode (AUTO).

Notes

• When mopping, we recommend cleaning the individual rooms.
• When mopping, check the vacuum cleaner and add water to the moping attachment, if necessary, or rinse the mop.
• Remove and clean the moping attachment after use. Do not leave it installed on the vacuum cleaner while charging.

VACUUM CLEANER MAINTENANCE

Carry out maintenance and cleaning regularly, depending on the frequency of use and the amount of cleaning. In a more polluted environment (a pet household), more frequent maintenance will be required. Failure to carry out maintenance may damage the vacuum cleaner and its components!

6.1 CHARGING CONTACTS CLEANING
Switch off the vacuum cleaner and disconnect the charging station from the power supply! Clean the charging contacts (A3, D2) on the vacuum cleaner and on the station with a soft dry cloth. Clean at least once a month. Do not use aggressive cleaning agents or oils to clean the contacts.

6.2 DIRT TANK AND FILTERS CLEANING

1. Remove the dirt tank B from the vacuum cleaner. Dispose of dirt together with normal household waste.

2. Disassemble dirt container B, and take out HEPA filter B3 and separator B6.

3. Rinse separator B6 in flowing water. You can also remove cover element B7 to make the maintenance easier.

4. Clean the dirt tank with tool H (or other suitable).

5. Blow or knock the HEPA filter B3 gently. NOTICE
   – Dry cleaning is recommended to maintain HEPA filter parameters.
   – If you choose to wash the HEPA filter with water, its filtering ability will be reduced.
   – The maximum number of filter washes is 3x. Then it is necessary to buy a new one.
   – It is recommended to change the HEPA filter at least twice a year.
   – The HEPA filter is not suitable for washing in the dishwasher.
   – Cleaning failure and possibly filter replacement can lead to malfunction of the vacuum cleaner!

6. After rinsing, allow all items to dry thoroughly, then assemble the dirt container and fit it back into the robot vacuum.

6.3 SIDE BRUSHES CLEANING

1. Remove the two side brushes, clean them and remove the twisted hair/pet’s hair).
2. Fit the brushes on the robot vacuum. Observe side marks (L – left, P – right).

6.4 WHEELS CLEANING
Clean the front, left, and right wheels with the H device. You can remove the front wheel A6 with its fixture to make maintenance easier. After the maintenance, put the front wheel back in place.

NOTICE
Some hair/pet’s hair may be wrapped around the wheel axes and other dirt may stick. Inspect and clean the wheels regularly.

6.5 SENSORS CLEANING
After each cleaning, clean the sensors with tool H (or another suitable one).

6.6 MOP EXTENSION CLEANING

1. Remove mop unit G from the device.
2. Remove mop G3 from the mop unit. Drain excess water from the tank. Rinse the tank with water. Rinse mop G3 in flowing water. Allow all items to dry before storage.

More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by a professional service! Failure to comply with the instructions of the manufacturer will lead to the expiration of the right to guarantee repair!

PROBLEMS SOLUTIONS

horizontally
E05| Dirty sensors| Check and clean the sensors
E06| Front bumper error| Check and clean the front bumper
E08| Side brushes got stuck| Check and clean side brushes
E09| Robot vacuum trapped in a narrow space| Place the robot vacuum on a free area
E10| Battery discharged| Charge the battery
E24| Dirt container/mop unit error| Check the dirt container/mop unit and install it correctly

TECHNICAL SPECIFICATION

Robotic vacuum cleaner

Appliance protection class| III.
operating voltage| 14.4 V (DC)
Accumulator| Li-Ion
Battery savings| 2400 mAh
Charging time| 4-6 hours
Weight| 2.3 kg
Dimensions| Ø 311 mm x 76 mm
The declared acoustic level is 72 dB(A) re 1pW.
Charging adapter

Device manufacturer’s name or trademark, business registration number, and address| ETA
AC adapter model identifier| S012DBV1900060
Input voltage| 100-240 V (AC)
Input frequency| 50/60 Hz
Output voltage| 19 V (DC)
Output current| 0.6 A
Output power| 11.4 W
Average efficiency in active mode| 84.85%
Low load efficiency (10%)| 76.32%
Power consumption without load| 0.057 W
Appliance protection class| II.
Charging station

Appliance protection class| III.
Input voltage| 19 V (DC)

Hereby, ETA a.s. declares that the radio equipment type ETA1227 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the ETA internet address.
The manufacturer reserves the right to change the technical specifications for the respective model.
A guarantee of 24 months does not apply to a decrease in the accumulator’s effective capacity caused by its use or age. Effective capacity gradually decreases depending on the method of use of the accumulator.

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for the production of packing, components, and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be received free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations.
The appliance is equipped with a Li-Ion battery with long life. For environmental protection, it is necessary to remove the battery from the appliance after its service life and the battery and the appliance must be disposed of safely using special collection networks. Ask for more details at the local authority or at the local waste collection site.
For environmental protection, it is necessary to remove the battery from the appliance after its service life and the battery and the appliance must be disposed of safely using special collection networks. Ask for more details at the local authority or at the local waste collection site.
Battery removing
Remove the 4 battery compartment cover screws at the bottom of the vacuum cleaner. Remove the battery and unplug the connector. Remove the battery and unplug the connector. For unplugging the connector use more force to the advantage of overcoming the safety fuse against spontaneous disconnection.
HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.
TO AVOID THE DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES, OR PLAYPENS. THIS BAG IS NOT A TOY.
– Please read the instructions manual
– Removable power supply unit
NOTICE

© DATE 13/05/2021
e.č. 30/2021

Documents / Resources

| eta ZERO 2 in 1 Robot Vacuum Cleaner [pdf] User Manual
ZERO 2 in 1 Robot Vacuum Cleaner, ZERO, 2 in 1 Robot Vacuum Cleaner, Robot Vacuum Cleaner, Vacuum Cleaner, Robot Cleaner, Vacuum
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>