FLEX DWL 2500 10.8 LED Cordless High Spectrum Light Instruction Manual

: June 13, 2024
: FLEX

Table of Contents

Symbols used in this manual
Symbols on the power tool
For your safety
Overview
Instructions for use
Assembly
Maintenance and care
Disposal information
Exemption from liability
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LEX DWL 2500 10.8 LED Cordless High Spectrum Light Instruction Manual

Symbols used in this manual

WARNING!
Denotes impending danger. Non-observance of this warning may result in death or extremely severe injuries.
CAUTION!
Denotes a possibly dangerous situation. Non-observance of this warning may result in slight injury or damage to property.
NOTE
Denotes application tips and important information.

Symbols on the power tool

Read Icon
Before switching on the power tool, read the operating manual!
Disposal Icon
Disposal information (see page 15)!
Do not look into the light source!

Rugged lamps IK07

Dust-proof degree 2 and protection against ingress of water 0 (with battery)
IP20 Dust-proof degree 6 and protection against ingress of water 7 (without battery)
WARNING- Risk of fire Minimum distance from lighted objects 0.1 m

For your safety

WARNING!
Before using the power tool, please read and follow:

these operating instructions,
the ”General safety instructions” on the handling of power tools in the enclosed booklet (leaflet-no.: 315.915),
the currently valid site rules and the regulations for the prevention of accidents.

Intended use
The LED rechargeable work lamp DWL 2500 10.8/18.0 is designed for for commercial use in industry and trade,

checking large surfaces during polishing, painting and cleaning as well as colour matching
for targeted illumination of the workplace,
for illuminating rooms

The LED rechargeable work lamp DWL 2500 10.8/18.0 is not suitable for use as a headlight.

Safety instructions for LED rechargeable work lamps

WARNING!
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injuries. Save all warnings and instructions for future reference.

Do not use the LED rechargeable work lamp in a potentially explosive environment.
Do not point the light beam at people or animals and do not look into the light beam, even from far away.
Do not cover the lamp head while the LED rechargeable work lamp is in use. The lamp head heats up when in use and the accumulating heat may cause burns.
The light source of this lamp cannot be replaced. You must replace the entire lamp if it no longer works due to a defect or because its service life has expired.
Do not use the LED rechargeable work lamp in road traffic.
Remove the battery from the rechargeable work lamp before transporting, storing or performing any work on the rechargeable work lamp (e.g. installation, maintenance, etc.).
Do not let children use the LED rechargeable work lamp. It is designed for professional use. Children may be accidentally blinded or may blind others.
Do not open the battery. There is a risk of a short-circuit.
Protect the battery from heat, e.g. from continuous exposure to sunlight, fire, water and humidity. There is a risk of explosion.
If the battery is damaged or used improperly, fumes may be emitted. Provide fresh air and consult a doctor if you feel unwell. The fumes may irritate the respiratory tract.
Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Pointed objects, such as nails or screwdrivers, or external forces may damage the battery. This may cause an internal short-circuit and the battery to burn, smoke, explode or overheat.
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.

Technical specifications

| DWL 2500 10.8/18.0
---|---
Machine type| LED rechargeable work lamp
Lithium-ion battery| V/Ah| 18.0/2.5 18.0/5.0 10.8/2.5 10.8/4.0 10.8/6.0
Lighting duration| h| Max. 30 Backup: 2h at 10%/300 lm
Colour temperature| K| 2500/3500/4500/5500/6500
Total flux| lm| 3000/100% 2250/75% 1500/50% 750/25% 300/10%
Weight according to “EPTA Procedure 01/2003” (without battery)| kg| 1.9
Size (LxWxH)| mm| 240x230x120

Overview

Support frame
LED unit
Slot for battery
Handle
Mounting option for a tripod
USB port
Control element
Li-ion battery (2.5 Ah or 5.0 Ah)
Release button for battery
State of charge indicator

Instructions for use

WARNING!
Remove the battery before carrying out any work on the power tool.

Before switching on the power tool
Unpack power tool and accessories and check that no parts are missing or damaged.

Inserting/replacing the battery

Press charged battery fully into the power tool.
To remove the battery, press the release buttons (1.) and pull out the battery (2.).

CAUTION!
When the device is not in use, protect the battery contacts. Loose metal parts may short-circuit the contacts; there is a risk of explosion and fire!

Battery state of charge

Press the button to check the state of charge at the state of charge indicator LEDs.

The indicator goes out after 5 seconds. If one of the LEDs flashes, the battery must be recharged. If none of the LEDs light up after the button is pressed, the battery is faulty and must be replaced.

Switching on and off

Switch the LED rechargeable work lamp on and off by pressing the on/off switch.

Adjusting light intensity
The light intensity of the LED rechargeable work lamp can be adjusted by pressing “+” or “-“.
The LED display on the left indicates the remaining lighting duration.

Adjusting colour temperature
You can change the colour temperature of the LED rechargeable work lamp incrementally in 5 stages by pressing the on/off switch for longer than 2 seconds and then pressing the “+” and “-” button.

Bluetooth® control
The LED rechargeable work lamp can be controlled via the integrated Bluetooth® light control system. Activate by pressing the “Bluetooth® button” and connect to the app.

Functions

Switch lamp on/off
Adjust light intensity
Select colour temperature
Connect up to 4 lamps together
Select pin code so that no one else can control the lamp

The process to delete the pin code is

Turn on the Bluetooth function.
Press the Bluetooth button for 10 second.
The pin code is reset.

Compatible with iPhone 5 or higher/Android 5.0 or higher.
Visit the iTunes App Store/Google Play/or download the app from our website.

Powerbank function
The LED rechargeable work lamp has an integrated powerbank. The lamp lasts for up to 2 hours with a luminous flux of 300 lumen – without rechargeable battery. With rechargeable battery- It allows mobile units, e.g. smartphones, to be charged via the USB socket.

Charge voltage/current: 5V/1A

Assembly

You can set up the LED rechargeable work lamp in any position with the aid of a support stand.
Assembly

You can mount the LED rechargeable work lamp on a tripod or attach it to any magnetic surface with the aid of a magnet holder.
Assembly

Maintenance and care

Cleaning

WARNING!
Before performing any work, pull out the mains plug.
Do not use water or liquid detergents.

Remove dirt and dust from the housing with a paint brush or dry cloth.

Repairs
Repairs may be carried out by an authorised customer service centre only.

Spare parts and accessories
Exploded drawings and spare-part lists can be found on our homepage:
www.flex-tools.com

Disposal information

WARNING!
Render redundant power tools unusable:

mains operated power tool by removing the power cord,
battery operated power tool by removing the battery

EU countries only:
Do not dispose of electric power tools in the household waste!
In accordance with the European Directive 2012/19/EU on Waste Electrical and Electronic Equipment and its incorporation into national law, used power tools must be collected separately and recycled in an environmentally friendly manner.

Raw material recovery instead of waste disposal.
Device, accessories and packaging should be recycled in an environmentally friendly manner. Plastic parts are identified for recycling according to material type.

WARNING!
Do not throw batteries into the household waste, fire or water. Do not open used batteries.

Accumulators/batteries should be collected, recycled or disposed of in an environmentally friendly manner.

EU countries only:
In accordance with Directive 2006/66/EC defective or used batteries must be recycled
NOTE
Please ask your dealer about disposal options!

Exemption from liability

The manufacturer and his representative are not liable for any damage and lost profit due to interruption in business caused by the product or by an unusable product. The manufacturer and his representative are not liable for any damage which was caused by improper use of the power tool or by use of the power tool with products from other manufacturers.

FLEX-Elektrowerkzeuge GmbH Bahnhofstr. 15 71711 Steinheim/Murr Tel. +49 (0) 7144 828-0 Fax +49 (0) 7144 25899
info@flex-tools.com
www.flex-tools.com

LEX Logo