GE 81726LO 216 Light 19.6 ft White Integrated LED Christmas Tape Lights Instruction Manual
- June 13, 2024
- GE
Table of Contents
GE 81726LO 216 Light 19.6 ft White Integrated LED Christmas Tape Lights
Product Information
- Model: ETL MODEL NO. LT-FPC-2835-2.77CM-6M-120V-W+F NHL MODEL NO. 81726LO
- Input Voltage: 120V
- Frequency: 60Hz
- Current: 0.08A
- Country of Origin: Vietnam
Product Usage Instructions
- Read and follow all safety instructions provided in the manual.
- Do not cover the product as it may cause overheating and potential hazards.
- Ensure the flexible light is not tightly coiled during operation.
- Avoid puncturing, cutting, shortening, or splicing the flexible lighting.
- Avoid routing the cord or flexible lighting through walls, doors, windows, or any part of the building structure.
- Regularly inspect the light and cord insulation for any damage. Do not use if there is any damage.
- Avoid submerging the flexible light in liquids or using it near standing water.
- Secure the flexible light using only the hangers or clips provided. Do not use staples, nails, or similar means that may damage insulation.
- Avoid continuous flexing of the flexible lighting.
- Ensure proper plug orientation when connecting to a polarized outlet. If the plug does not fit, reverse it or consult a qualified electrician.
- Disconnect all units before adding additional segments.
- Use only extension segments of the same series and manufactured by the same manufacturer.
- Tightly secure all connections and the end cap on the last segment to prevent water entry.
- Avoid installing on gates or doors that are subject to flexing.
- Do not mount or secure the light in a way that can cut the outer jacket or damage cord insulation.
- Inspect the light before use and discard any with broken outer jackets, loose connections, or frayed wire insulation.
- Do not replace the attachment plug. If damaged, discard the product.
- Avoid continuous rubbing or kneading of the product. Maintain a minimum bending radius of more than 8cm.
- Avoid tight coiling of the flexible light and maintain at least 12mm spacing between cables or parts to prevent overheating.
- Do not install in cabinets, tanks, or enclosures of any kind.
Outdoor Use Safety Precautions
- Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuits or outlets used for outdoor use.
- Use only outdoor extension cords with appropriate designations marked on the wire (e.g., type SW, SOW, STW, STOW, SJW, SJOW, SJTW, or SJTOW).
Always remember to read and follow all instructions provided with the product to ensure safe and proper usage.
THE GUIDELINE FOR LED TAPE LIGHT
ETL MODEL NO. LT-FPC-2835-2.77CM-6M-120V-W+F
NHL MODEL NO. 81726LO 120V, 60Hz, 0.08A
Made in Vietnam
IMPORTANT SAFETY INSTRUCTIONS
- READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Do not cover this product as the covering may cause the flexible light to overheat and melt or ignite.
- Do not operate with the flexible light tightly coiled.
- Do not puncture, cut, shorten, or splice the flexible lighting.
- Do not route the cord or flexible lighting through walls, doors, windows or any like part of the building structure.
- Do not use if there is any damage to the light or cord insulation. Inspect periodically.
- Do not submerge flexible light in liquids, or use the product in the vicinity of standing water or other liquids.
- Secure this flexible light using only the hangers or clips provided. Do not secure this product or its cord with staples, nails, or like means that may damage the insulation or permanently attach to the building structure.
- Do not subject flexible lighting to continuous flexing.
- This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug, if it still does not fit, contact a qualified electrician. Never use with an extension cord unless plug can be fully inserted. Do not alter or replace the plug.
- All units must be unplugged before adding additional segment.
- Use only the same series extension segments model manufactured by the same manufacturer, .
- Ensure all connections and the end cap on the last segment is tightly secured to preclude the entry of water.
- Do not install on gates or doors, where subject to flexing.
- Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.
- Do not rub or knead the products continuously, the smallest bending radius is more than 8cm.
- Do not operate with the flexible light tightly coiled. To prevent overheating do not allow contact between flexible light cables and parts of light cables. Maintain at least 12mm spacing between flexible light cables or parts of light cables.
- Do not install in cabinets, tanks or enclosures of any kind.
WARNING-Risk of fire and electric shock, uncoil flexible light prior to plugging into receptacle. SAVE THESE INSTRUCTIONS
WARNING: When using “outdoor” use portable lighting products, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following:
READ ALL INSTRUCTIONS
- Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuits or outlet to be used for the outdoor use flexible lighting product. Receptacles are available having built-in GFCI protection for this measure of safety.
- Use only outdoor extension cords, such as type SW, SOW, STW, STOW, SJW, SJOW, SJTW, or SJTOW. This designation is marked on the wire of the extension cord.
- Do not install closer than 3 meters from a swimming pool surface.
Tools Required:
Accessories(Includes):
HOW TO REPLACE THE FUSE
This plug contains an electrical fuse a safety feature.
- Disconnect power before replacing the fuse.
- Grasp plug and remove from the receptacle or other outlet device.
- Do not unplug by pulling on the cord.
- Slide open by unscrew the fuse access cover on top of attachment plug.
- Remove old fuse carefully.
- Never attempt to replace the fuse with a higher watt fuse.
- Use only 5 A, 125 V fuse. Failure to do so may be a fire hazard.
- Set new fuse in holder and reinstall access cover.
HOW TO INSTALL TAPE LIGHT
The design of tape light follows the principle of user-friendly and customized. User can install it in different smooth surface, such as wood, plastic, metal and porcelain, etc. It can be design an apply in different shape, easy to connect
- Face up lighting part when in stall clips.
- Check all accessories are in properly installation before plug to electricity.
- Bend only back, do not bend from side.
- Fix mounting clips with nails or screws onto support surfaces. (Figure 1, 2; 3)
- Mounting clips, suction cup should be evenly spaced and both be a maximum of 1M apart. ( Figure 4)
- Make sure that the distance between two lines of lighting chains should be at least 12 mm.
- The maximum connected quantity should refer to caution label.
- Please use the accessories (clips and screws) we provided.
- Please do not cut this products.
For questions and/or assistance, call customer service at
1-877-398-7337 or visit us on the web
at www.geholidaylighting.com PRINTED IN
VIETNAM NV 0323 MADE IN VIETNAM
©2023 Nicolas Holiday Limited, Suite 2706 Skyline Tower, 39 Wang Kwong
Road,Kowloon Bay, Kowloon, Hong Kong
All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>