CYP CPLUS-V4H4HP 4K UHD+ 4 x 4 Matrix with USB Power Supply User Manual

CYP CPLUS-V4H4HP 4K UHD+ 4 x 4 Matrix with USB Power Supply

Product Information

• Product Name: C PLUS- V4H4HP
• Product Type: 4K UHD+ 4 x 4 Matrix with USB Power Supply
• Operation Manual: Included
• Disclaimers: Please read all instructions before unpacking, installing, or operating this equipment and before connecting the power supply. All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
• Safety Precautions: Keep the following in mind as you unpack and install this equipment.

Revision History

1. Version No.
2. Date (DD/MM/YY)
3. Summary of Change
   • RDV1
   • 31/10/16
   • Preliminary Release

Product Usage Instructions

Power
Press the power button to turn on the unit (green LED) or place it into standby mode (red LED).

IR Receiving Window
The IR receiving window accepts IR signals from the included IR remote for control of this unit only.

Input/Output Routing

1. Press the OUT keys (A~D) of the outputs you wish to route a source to (they will flash to indicate selection).
2. Next, press the IN key of the input (1~4) you wish to route to the selected outputs.
3. Finally, press CONFIRM to confirm your selection and execute the routing change.

Cancel
Press the CANCEL button to cancel newly made input/output/preset routing selections before they have been confirmed.

Menu

• Press MENU to enter the LCD menu or to go back out from menu items.
• Press ENTER to confirm a selection within the LCD menu or to go deeper into a menu item.
• Press – / + to move up and down or adjust selections within menus.

All

• Press ALL to select all outputs simultaneously for routing.
• Next, press the IN key of the input (1~4) you wish to route to all outputs.
• Finally, press CONFIRM to confirm your selection and execute the routing change.

Preset

• Press PRESET to enter the preset recall menu in the LCD window.
• Press the +/- buttons followed by the ENTER button to select and activate the preferred preset.

Lock

• Press LOCK to lock all button functions on the front panel.
• Press and hold for 3 seconds to release the lock function. The LCD will display “Lock” when the function is active.

Mute

• The MUTE button functions as a blank audio/video source.
• To use it, follow the standard matrix routing instructions, but use the MUTE button as the input to blank out the selected outputs.
• When a MUTE input is in use, it will show up as “M” within the routing display.

DISCLAIMERS

• The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use.
• Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document.
• Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice.

COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means—electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from Cypress Technology.

• © Copyright 2015 by Cypress Technology.
• All Rights Reserved.

TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this equipment:

• Always follow basic safety precautions to reduce the risk of fire, electrical shock, and injury to persons.
• To prevent fire or shock hazards, do not expose the unit to rain, or moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person to walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.

REVISION HISTORY

INTRODUCTION

This 4K UHD 4 by 4 Matrix provides the ability to connect up to four 4K UHD HDMI sources to up to four 4K UHD HDMI displays and freely switch between them. This unit comes with full support for 18Gbps (600Mhz) resolutions up to and including 4K@60Hz (4:4:4, 8-bit) as well as support for 48-bit Deep Color, HDR (High Dynamic Range), HD audio and other features defined by the HDMI 2.0 specification. With a comprehensive EDID management feature that includes the ability to select between built-in default EDID, EDID copied from connected sink devices, as well as a configurable EDID, this matrix can solve many interconnectivity problems. This unit also features four USB ports that supply up to 5V/1A power for use with connected optical fiber or AOC fiber cable extenders. By using these specialized cables your HDMI content can be extended much further than would be possible with normal HDMI cables. The built-in OSD has the ability to display user-editable general information text so each output can display up to 2 lines of customized text on top of the video source in the color of your choice. This unit provides an intuitive set of front panel controls with an OSD as well as RS-232, telnet, WebGUI, and IR remote control options.

APPLICATIONS

• Smart Home Control
• Control Center
• Function Room
• Product Showroom
• Ballroom

PACKAGE CONTENTS

• Matrix unit x 1
• 24V/3.75A Adaptor with power cord x 1
• Remote control unit x 1 (CR-177)
• Rack ear set x 1
• Operation manual x 1
• HDMI source equipment such as media players, video game consoles or set-top boxes.
• HDMI receiving equipment such as HDTVs, monitors, or audio amplifiers.
• The use of “Premium High-Speed HDMI” cables is highly recommended.

FEATURES

• HDMI input and output with 18Gbps (600MHz) 4K UHD support
• DVI 1.0 compliant with the use of an HDMI-DVI adaptor
• HDCP 1.4 and 2.2 compliant
• Supports HD resolutions up to 3840×2160@60 Hz (YUV 4:4:4, 8-bit) & 4096×2160@60 Hz (YUV 4:4:4, 8-bit)
• Supports 48-bit Deep Color up to 1080p60
• Supports pass-through of LPCM 7.1, bitstream, and HD bitstream audio formats
• Supports six internal EDIDs, four external EDIDs copied from connected devices, and four user-provided EDIDs
• Four USB ports to supply 5V/1A power to optical fiber and AOC fiber extension cables
• OSD with user-customizable information text
• Intuitive control interface including telnet, WebGUI, OSD, IR remote, and RS-232
• Easy firmware update via USB thumb drive in the field

OPERATION CONTROLS AND FUNCTIONS

Front Panel

1. Power: Press this button to power the unit on (green LED) or place it into standby mode (red LED).

2. IR Receiving Window: Accepts IR signals from the included IR remote for control of this unit only.

3. IN 1~4 & OUT A~D: Press the “OUT” keys (A~D) of the outputs you wish to route a source to (they will flash to indicate selection). Next, press the “IN” key of the input (1~4) you wish to route to the selected outputs. Finally, press “CONFIRM” to confirm your selection and execute the routing change.

4. CONFIRM: Press this button to confirm newly made input/output routing selections.
   CANCEL: Press this button to cancel newly made input/output/preset routing selections before they have been confirmed.

5. MENU: Press to enter the LCD menu, or to back out from menu items.

   • ENTER  Press to confirm a selection within the LCD menu or to go deeper into a menu item.
   • – / +: Press to move up and down or adjust selections within menus.

6. ALL: Press this button to select all outputs simultaneously for routing. Next, press the “IN” key of the input (1~4) you wish to route to all outputs. Finally, press “CONFIRM” to confirm your selection and execute the routing change.

7. PRESET: Press to enter the preset recall menu in the LCD window. Press the “+/-” buttons followed by the “ENTER” button to select and activate the preferred preset.

8. LOCK: Press to lock all button functions on the front panel. Press and hold for 3 seconds to release the lock function. The LCD will display “Lock” when the function is active.

9. MUTE: The “MUTE” button functions as a blank audio/video source. To use it, follow the standard matrix routing instructions, but use the “MUTE” button as the input to blank out the selected outputs. When a “MUTE” input is in use it will show up as “M” within the routing display.

10. LCD window: Displays the unit’s menu, settings, and information.

Rear Panel

1. HDMI IN 1~4: Connect to HDMI source equipment such as media players, game consoles, or set-top boxes.
2. OPTICAL/HDMI OUT A~D: Connect the HDMI outputs to devices such as HDMI TVs, monitors, or amplifiers for digital video and audio output. Connect the optical outputs to powered speakers or amplifiers for digital audio output using an appropriate optical cable. The audio from each optical output will be the same as the HDMI output it is paired with.
3. USB POWER OUTPUT 1 ~ 4: Each USB port provides 5v/1A of power intended for use with HDMI over AOC (Active Optical Cables) fiber optic video extension cables.
4. SERVICE: This slot is reserved for firmware update use only.
5. CONTROL: Connect directly, or through a network switch, to your PC/laptop to control the unit via telnet/WebGUI.
6. RS232: Connect directly to a PC, laptop or other serial control device to send RS-232 commands to control the unit.
7. IR IN: Connect to the provided IR Extender to extend the IR control range of the unit. Ensure that the remote being used is within direct line-of-sight of the IR Extender.
8. DC 24V: Plug the 24V DC power adapter into the unit and connect it to an AC wall outlet for power.

Remote Control

• POWER: Press to power the unit on or place it into standby mode.

• 1/A ~ 4/D: Press these keys to configure the video routing. Press the “OUT” key followed by the key (A~D) of the outputs you wish to route a source to (they
  will flash to indicate selection). Next, press the “IN” key followed by the input (1~4) you wish to route to the selected outputs. Finally, press “ENTER” to confirm your selection and execute the routing change.
  Note: Keys 5/E ~ 8/H have no function with this matrix.

• ALL: Press this key to select all outputs simultaneously for routing. Next, press the key of the input (1~4) you wish to route to all outputs. Finally, press “ENTER” to confirm your selection and execute the routing change.

  • MUTE: Press this key to mute the video output. Press the key of the input (1~4) you wish to route then press a mute key to mute the video output.
  • INFO: Switches the information displayed on each output’s OSD between the user-customized text and the current video/Ethernet details.
  • PRESET: Press to enter the preset call menu in the LCD window. Press the “+/-” buttons followed by the “ENTER” button to select and activate the preferred preset.

• MENU: Press to enter the LCD menu, or to back out from menu items.

  • ENTER Press to confirm a selection within the LCD menu or to go deeper into a menu item.
  • CANCEL: Press to cancel newly made input/output/preset routing selections before they have been confirmed.
  • Plus (+) / IN: Press “+/IN” to navigate up within menus or to begin the selection of an input for routing.
  • Minus (-) / OUT: Press “-/OUT” to navigate down within menus or to begin the selection of outputs for routing.

LCD Menu Tree

DHCP)/ IP/Mask/Gate/MAC

Network Setup| Mode: (Static/DHCP)
Static: IP/Mask/Gate|
Firmware| Version
Firmware Update| USB update
Factory Reset| Factory reset

IR Cable Assignments

RS-232 Protocol

MATRIX| ****

►

◄

| REMOTE CONTROLLER
---|---|---
Pin| Assignment| Pin| Define TX / RX
1| NC| 1| NC
2| TX| 2| RX
3| RX| 3| TX
4| NC| 4| NC
5| GND| 5| GND
6| NC| 6| NC
7| NC| 7| NC
8| NC| 8| NC
9| NC| 9| NC

• Baud Rate: 115200bps
• Data Bits: 8
• Parity: None
• Flow Control: None
• Stop Bits: 1

RS-232 Command

command.

| ? command
HELP| Show descript of

command.

| ? command
ETH_FADEFAULT| All Ethernet

configure set to

factory default.

| NONE
SIPMODE| Set Ethernet IP mode.| SIPMODE P P=Mode(STATIC/DHCP)

SETIP

| ****

Set Ethernet IP address, subnet mask, gateway.

| SETIP P1 P2 P3 P1=IPADDRESS P2=NETMASK P3=GATEWAY (P1~P3)=X.X.X.X (X=0~255)
IPCONFIG| Display the cur-

rent IP configu- ration

| NONE
REBOOT| System reset| NONE
QUIT| Telnet QUIT| NONE
P0| Power off.| NONE
P1| Power on.| NONE
STORE| Store current I/O position| STORE P

P=Port(1~4)

SHOW| Show current

port’s I/O posi- tion

| STORE P

P=Port(1~4)

PRESET| Preset the store I/O position| PRESET P

P=Port(1~4)

NAME

| ****

Set Preset name

| NAME NAME P1 P2

P1=Port(1~4) P2=Name(1~8 Characters)

I| Set all output source| IP

P=Input Port(1~4)

ST| Show firmware

version

| NONE
RS| System Reset to

A1,B2,C3,D4.

| NONE
---|---|---

EM

| ****

Setting EDID mode.

| EM P1 P2 P1=PORT(1~4)

P2=(1-FHD2CH, 2-FHD- MCH, 3-4KUHD2CH, 4-4KUH- DMCH, 5-4KUHD+2CH,

6-4KUHD+MCH, 7-TXA,8-TXB,

9-TXC,10-TXD, 11-USER1, 12- USER2, 13-USER3, 14-USER4)

UPDATE

| Update firmware

by SERVICE USB

port. note:Device will wating for the USB device

plug in or power cycle to reboot.

| ****

NONE

A| Set output A source.| AP

P=Input Port(1~4)

B| Set output B source.| BP

P=Input Port (1~4)

C| Set output C source.| CP

P=Input Port (1~4)

D| Set output D source.| DP

P=Input Port (1~4)

AB..

| Set output

ABCD… source at the same time.

| AB..P

P=Input Port (1~4)

USEREDID

| Set user EDID name.| USEREDID P1 P2

P1=Port(1~4) P2=Name(1~8 Characters)

FADEFAULT| All configure set

to factory de- fault.

| NONE
OSDON| OSD on.| OSDON P

P=Output Port(1~4)

OSDOFF| OSD off.| OSDOFF P

P=Output Port(1~4)

---|---|---

OSDXY

| ****

Set OSD coordi- nate.

| OSDXY P1 P2 P3

P1=Output Port(1~4) P2=x(1~1920) P3=y(1~1080)

OSDSTR

| ****

Set OSD string.

| OSDSTR P1 P2 P3

P1=Output Port(1~4) P2=Line(1~2) P3=String(1~64 Charac-

ters)

OSDFSIZE

| Set OSD font

size.

| OSDFSIZE P1 P2

P1=Output Port(1~4) P2=Size(1~3)

OSDFCOLOR

| Set OSD font color.| OSDFCOLOR P1 P2

P1=Output Port(1~4) P2=Font Color(1~9)

OSDBGCOLOR

| Set OSD back- ground color.| OSDBGCOLOR P1 P2

P1=Output Port(1~4) P2=Background Color(1~9)

OSDTS

| Set OSD back- ground transpar- ent level.| OSDTS P1 P2

P1=Output Port(1~4) P2=Transparent Level(1~8)

OSDINFO| Set OSD informa- tion on off.| OSDINFO P

P=Action(ON/OFF)

ROSDINFO| Get OSD infor-

mation status.

| NONE

USBPWR

| USB power on/ off.| USBPWR P1 P2

P1=Output Port(1~4) P2=Action(ON/OFF)

Telnet Control

• Before attempting to use telnet control, please ensure that both the unit and the PC/Laptop are connected to the same active networks.
• To access Telnet in Windows 7, click on the “Start” menu and type “cmd” in the search field, then press “Enter”.
• Under Windows XP go to the “Start” menu, click on “Run”, type “cmd” then press “Enter”.
• Under Mac OS X, go to Go→Applications→Utilities→Terminal See below for reference.

Once in the CLI (Command Line Interface) type “telnet” followed by the IP address of the unit and “23”, then hit “Enter”.

This will connect us to the unit we wish to control. Type “help” to list the available commands.

WebGUI

Install the IP Discovery Tool:

1. Please obtain the Device Discovery software from your authorized dealer and save it in a directory where you can easily find it.
   Note: The unit’s default IP address is 192.168.1.50

2. Connect the unit and your PC/Laptop to the same active network and execute the Device Discovery software. Click on “Find Devices on Network” and a list of devices connected to the local network will show up indicating their current IP address.

3. By clicking on one of the listed devices you will be presented with the network details of that particular device. If you choose, you can alter the static IP network settings for the device, or switch the unit into DHCP mode to automatically obtain proper network settings from a local DHCP server. To switch to DHCP mode, please select DHCP from the IP mode drop-down, then click “Save” followed by “Reboot”.

4. Once you are satisfied with the network settings, you may use them to connect via telnet or WebGUI. The network information window provides a convenient link to launch the WebGUI directly.

Login to the WebGUI:

1. By default, both the Username and Password are “admin” for the WebGUI. The administrator password can be changed within the “System Settings” tab of the WebGUI if desired.
2. The following function tabs will always display on the left side of the WebGUI to aid with navigation.

Switch
This page provides video routing settings, preset saving/loading, and I/O renaming options.

Video Routing
To begin assigning a new video route, please click the button of the HDMI output you wish to send video to and then click on the button of the preferred HDMI input port. If desired, you may select more than one output prior to selecting the input. As you select each button they will change their color to orange. The new route will become active immediately after selecting the input port and the routing information displayed on the buttons will change accordingly.

Output Video Mute
Each output can be individually muted (black video, no audio). To mute an output, please click the ( ) icon within the appropriate output button. To unmute the output, please click the icon a second time.

Output and Input Naming
All inputs and outputs can be renamed as required. To rename the input and output ports please click the “edit” icon ( ). Click the “Save” button to confirm the change.

Note: Blank spaces (“ ”) are not allowed in names.

OSD Text Settings
Each output can display up to 2 lines of customized OSD text. The text can be customized in content, color, background transparency, size, and position. Click the “edit” icon ( ) associated with each output to modify these settings. Please click the “Save” button after making changes to the positioning or content. All other changes occur as soon as they are made.

Preset Setting
This matrix can store up to four video routing presets. Presets can be utilized to store multiple different routing states in advance for rapid, hassle-free, recall.

• Store: Once you have the matrix set the way you like, you can click the “Preset Set” icon ( ) in the upper right corner of the window and the Preset Set window will open. You may also name the preset at this stage by selecting the “edit” icon ( ). Click the main part of the Preset’s button to store the current state in that preset.
• Recall: When you wish to load a previously stored preset, please click the “Preset Recall” icon ( ) and you will be presented with a choice of the available 4 presets. Hovering the mouse over each button will display the preset routes stored within it. The preset will load immediately upon selecting the preset.

EDID Settings
This matrix provides the option of six standard EDIDs, four sink-sourced EDIDs and four customer-uploaded EDIDs that can be assigned to each input port individually. The names of the four customer upload-ed EDIDs can changed if desired.

Customer EDID Settings
To upload a custom EDID, please click the “Upload” button next to the Customer EDID Settings item you would like to change. An EDID Upload window will appear, allowing you to locate and upload your preferred EDID file from the file directory on your local PC. Once the correct file has been selected, please click the “Upload” button in the window, and the file will be transferred to the matrix.

Sink EDID Download
To save an existing custom EDID to your local PC please press the “Download” button next to the Customer EDID Settings item you would like to save. Depending on your browser settings you will either be asked where to save the downloaded file, or the file will be transferred to the default download location on your PC.

Set EDID Input Content
The Set EDID Input Content section allows for the assignment of an EDID to each individual input port, or to all inputs at once. Click on an input to open the EDID Source management window. Multiple inputs can be selected at once if desired. Select the new EDID source to use and the change will occur immediately.

Note: This matrix comes with the following 6 default EDIDs:

1. FHD/2CH: 1080p@60Hz(148MHz), LPCM 2.0, 8-bit color
2. FHD/MCH: 1080p@60Hz(148MHz), LPCM 7.1 & bitstream, 8-bit color.
3. 4K UHD/2CH: 3840×2160p@30Hz (297MHz), LPCM 2.0, Deep Color (8/10/12-bit)
4. 4K UHD / MCH: 3840×2160p@30Hz (297MHz), LPCM 7.1 & bit-stream, Deep Color (8/10/12-bit)
5. 4K UHD+ / 2Ch: 3840×2160p@60Hz (594MHz), LPCM 2.0, Deep Color (8/10/12-bit)
6. 4K UHD+ / MCH: 3840×2160p@60Hz (594MHz), LPCM 7.1 & bit-stream, Deep Color (8/10/12-bit)

Note:
In some rare cases, it is possible for custom or external EDIDs to cause compatibility issues with certain sources. If this happens, it is recommended to switch to one of the 6 default EDIDs for maximum compatibility.

System Setting
This page provides system configuration options including turning the unit’s power on/off, turning the USB power support on/off, changing the network settings, resetting the system to factory defaults, and updating the firmware.

Admin log out
Clicking the “Logout” tab will automatically log the user out of the WebGUI and return to the login page.

CONNECTION DIAGRAM

SPECIFICATIONS

Technical Specification

• Video Bandwidth 18Gbps (600Mhz)
• Input Ports 4 x HDMI
• Control Interfaces
  • 1 x IR In
  • 1 x RS-232
  • 1 x Service (USB)
  • 1 x Control
• Output Ports
  • 4 x HDMI
  • 4 x USB port (5V/1A power supply)
• Supported Resolutions
  • 480i~4K@24/50/60Hz
  • 4K@50/60Hz
  • VGA~WUXGA
• IR Frequency 38kHz
• Baud Rate 115200 bps
• Power Supply 24VDC/3.75A (US/EU standards, CE/FCC/ UL certified)
• Chassis Material Metal
• Color Black
• Dimensions
  • 438mm x 49mm x 269mm (W×H×D) [Case Only]
  • 482mm x 49mm x 274mm (W×H×D) [All Inclusive]
• Weight 2966g

Support Timing

Input & output / Timing (Hz)| HDMI

Input

| HDMI

Output

---|---|---
640×480@60/72/75/85| V| V
720×400@85| V| V
720x480p@59.94/60| V| V
720x576p@50| V| V
800×600@56/60/72/75/85| V| V
1024×768@60/70/75/85| V| V
1152×864@75| V| V
1280x720p@50/59.94/60| V| V
1280×768@60/75| V| V
1280×800@60RB/60| V| V
1280×960@60| V| V
1280×1024@60| V| V
1360×768@60| V| V
1366×768@60| V| V
1440x480i@59.94/60| V| V
1440x576i@50| V| V
1400×1050@60RB/60| V| V
1440×900@60RB/60| V| V
1600×900@60| V| V
1600×1200@60| V| V
1680×1050@60RB/60| V| V
1920×1080@60RB| V| V
1920x1080i@60| V| V
1920x1080p@23.97/24/25/29.97/30/59.94/60| V| V
3840x2160p@24/25/30| V| V
3840×2160@50/60(4:4:4)/50/60(4:2:0)| V| V
4096x2160p@24| V| V

HDMI Cable Length

CYPRESS TECHNOLOGY CO., LTD

• Home page: http://www.cypress.com.tw.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>