SKIL 3122 Battery Charger Instruction Manual

: June 13, 2024
: Skil

Table of Contents

SKIL 3122 Battery Charger Instruction Manual
ORIGINAL INSTRUCTIONS
Charger 3122/3123/3124/3129 INTRODUCTION
TECHNICAL DATA 1 2
SAFETY
USE
! remove battery from charger
- IMPORTANT:
- MAINTENANCE / SERVICE
! unplug charger from power source before cleaning

SKIL 3122 Battery Charger Instruction Manual

ORIGINAL INSTRUCTIONS

Charger 3122/3123/3124/3129 INTRODUCTION

This charger is intended for charging SKIL battery packs BR1*31****
This tool is not intended for professional use
Read and save this instruction manual

TECHNICAL DATA 1 2

Charging time depending on the battery capacity (in Ah, indicated on the nameplate of the battery) 2

SAFETY

SPECIFIC SAFETY INSTRUCTIONS FOR CHARGERS

This charger can be used by children aged 8 and above and by persons who have physical,
sensory or mental limitations or a lack of experience or knowledge
if a person responsible for their safety supervises them or has instructed them in the safe operation of the charger and they understand the associated dangers (otherwise, there is a danger of operating errors and injuries)
Supervise children (this will ensure that children do not play with the charger)
Cleaning and user maintenance of the battery charger shall not be made by children without supervision
Always check that the supply voltageis the same as the voltage indicated on the nameplate of the charger
In case of electrical or mechanical malfunction, immediately switch off the tool or unplug charger from power source
Only use SKIL battery packs BR1*31**** with this charger
Do not touch the contacts in the charger
Do not expose tool/charger/battery to rain
Do not charge battery in damp or wet environments
Do not use charger when damaged
Do not use charger when cord or plug is damaged; it must be replaced bya specially prepared cord available through the service organization
Do not use battery when damaged; it should be replaced immediately
Do not disassemble charger
Do not attempt to recharge non- rechargeable batteries with the charger
Permitted ambient temperature (charger):
- when charging ..40°C
- during operation –20…+50°C
- during storage –20…+50°C EXPLANATION OF SYMBOLS ON CHARGER
Read the instruction manual beforeuse
Only use the charger indoors
Double insulation (no earth wirerequired)
Do not dispose of electric tools and batteries together with householdwaste material
Time lag fuse (3124)8 Time lag fuse (3122/3123/3129)

USE

Charging battery 9
- remove battery from tool
- connect charger to power source as illustrated 9a
- both lights A and B turn on for 1second and then turn off again 9b
insert battery into charger as illustrated 9c
green light A starts flashingindicating that the battery is being charged 9b
when the battery is fully charged and green light A turns on 9d
remove battery from charger as illustrated 9d

! remove battery from charger

after charging period has ended thereby lengthening the service life of the battery

IMPORTANT:

if red light B starts flashing after inserting a battery, this means that the battery is damaged and shouldbe replaced 9b
if red light B turns on after inserting a battery, this may mean thatthe battery is too cold or too hot (charger only charges batteries when its temperature is between4°C and 40°C) 9b
the lithium-ion battery can becharged at any time (interrupting the charging procedure does not damage the battery)
the lithium-ion battery does not have to be empty before charging (no “memory-effect” as with nickel- cadmium batteries)
while charging, the charger and the battery may become warm to touch; this is normal and does not indicate a problem
ensure that the outside surface of the battery is clean and dry before inserting into charger
if you anticipate long periods of non- use for the tool, it is best to unplug the charger from its power source
a significantly reduced working period after charging indicates that the battery is worn out and should be replaced

MAINTENANCE / SERVICE

Keep charger clean

– clean charging contacts in charger with alcohol or contact cleaner

! unplug charger from power source before cleaning

If the charger should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for SKIL power tools – send the charger undismantled together with proof of purchase to your dealer or the nearest SKIL service station (addresses as well as the service diagram of the tool are listed on www.skil.com)
Be aware that damage due to overload or improper handling of the product will be excluded from the warranty(for the SKIL warranty conditions see www.skil.com or ask your dealer)

ENVIRONMENT

Do not dispose of electric tools, accessories and packaging together with household waste material (only for EU countries)
in observance of European Directive 2012/19/EC on waste of electricand electronic equipment and itsimplementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility
symbol 6 will remind you of thiswhen the need for disposing occurs