SKIL HD182001 Hammer Drill Owner’s Manual

June 3, 2024
Skil

HD182001 Hammer Drill
Owner’s ManualSKIL HD182001 Hammer Drill

Model: HD182001

WARNING: To reduce the risk of injury, the user must read and understand the
Owner’s Manual before using this product. Save these instructions for future reference.
For Customer Service
1-877-SKIL-999 OR
www.skil.com

WARNING

  • Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
    – Lead from lead-based paints.
    – Crystalline silica from bricks, cement, and other masonry products.
    – Arsenic and chromium from chemically-treated lumber.

  • Your risk from these exposures varies, depending upon how often you do this type of work. To reduce your exposure to these chemicals:

  • Work in a well-ventilated area.

  • Work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

  • Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas  with soap and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote absorption of harmful chemicals.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING
Read all safety warnings, instructions, illustrations and specifications provided with this power tool . Failure to follow all instructions listed below may result in electric shock,  fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE .
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Work area safety
Keep work area clean and well lit . Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust . Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool . Distractions can cause you to lose control.
Electrical safety
Power tool plugs must match the outlet . Never modify the plug in any way . Do not use any adapter plugs with earthed (grounded) power tools . Unmodified plugs and  matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators . There is an increased risk of electric shock if your body is earthed  or grounded.
Do not expose power tools to rain or wet conditions . Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord . Never use the cord for carrying, pulling or unplugging the power tool . Keep cord away from heat, oil, sharp edges or moving parts . Damaged or  entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use .
Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply . Use of a GFCI reduces the risk of electric shock.
Personal safety
Stay alert, watch what you are doing and use common sense when operating a power tool . Do not use a power tool while you are tired or under the influence of drugs,  alcohol or medication . A moment of inattention while operating power tools may result in  serious personal injury.
Use personal protective equipment . Always wear eye protection . Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for
appropriate conditions will reduce personal injuries.
Prevent unintentional starting . Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on . A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach . Keep proper footing and balance at all times . This enables better control of the power tool in unexpected situations.
Dress properly . Do not wear loose clothing or jewellery . Keep your hair, clothing and gloves away from moving parts . Loose clothes, jewellery or long hair can be caught in
moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used . Use of dust collection can reduce  dustrelated hazards.
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles . A careless action can cause severe injury within a  fraction of a second.
Power tool use and care
Do not force the power tool . Use the correct power tool for your application . The correct power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off . Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or  storing power tools . Such preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories . Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation . If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean . Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc . in accordance with these instructions, taking into account the working conditions and the work to be performed . Use of  the power tool for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Service
Have your power tool serviced by a qualified repair person using only identical replacement parts . This will ensure that the safety of the power tool is maintained.
SAFETY WARNINGS FOR HAMMER DRILLS
Safety instructions for all operations:
Wear ear protectors when impact drilling . Exposure to noise can cause hearing loss.
Use the auxiliary handle(s), if supplied with the tool . Loss of control can cause personal injury.
Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord . Cutting accessory  contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Safety instructions when using long drill bits:
Never operate at higher speed than the maximum speed rating of the drill bit . At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the  workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip in contact with the workpiece.
At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do not apply excessive pressure . Bits can bend causing breakage or loss of control, resulting in personal injury.

ADDITIONAL SAFETY WARNINGS
Use clamps or another practical way to secure and support the workpiece to a stable platform . Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
Do not drill, fasten or break into existing walls or other blind areas where electrical wiring may exist . If this situation is unavoidable, disconnect all fuses or circuit breakers
feeding this worksite.
Always wear safety goggles or eye protection when using this tool . Use a dust mask or respirator for applications which generate dust .
Use thick cushioned gloves and limit the exposure time by taking frequent rest periods.
Vibration caused by hammer-drill action may be harmful to your hands and arms.
Secure the material being drilled . Never hold it in your hand or across legs . Unstable support can cause the drill bit to bind causing loss of control and injury.
Never leave the trigger locked “ON” . Before plugging the tool in, check that the trigger lock is “OFF” . Accidental start-ups could cause injury.
Position the cord clear of rotating bit . Do not wrap the cord around your arm or wrist.
If you lose control and have the cord wrapped around your arm or wrist it may entrap you and cause injury.
Position yourself to avoid being caught between the tool or side handle and walls or posts . Should the bit become bound or jammed in the work, the reaction torque of the tool could crush your hand or leg.
If the bit becomes bound in the workpiece, release the trigger immediately, reverse the direction of rotation and slowly squeeze the trigger to back out the bit . Be ready for a strong reaction torque. The drill body will tend to twist in the opposite direction as the drill bit is rotating.
Do not grasp the tool or place your hands too close to the spinning chuck or drill bit.
Your hand may be lacerated.
Do not use the switch “Lock-On” feature in situations where drill bit binding is likely. (For example: just before the bit is ready to break through the material, anytime when using a “Hole Saw”, auger bits . . . . . . . . etc .) When the bit binds, the drill’s body will twist or kick-back in opposite direction and the release of the trigger “Lock-On” may  be difficult.
Be aware of the location and setting of the switch “Lock-On” button . If the switch is locked “ON” during the use, be ready for emergency situations to switch it “OFF”, by  first pulling the trigger then immediately releasing it without pressing the “Lock-On” button.
When installing a drill bit, insert the shank of the bit well within the jaws of the chuck . If the bit is not inserted deep enough, the grip of the jaws over the bit is reduced and  the loss of control is increased.
Do not use dull or damaged bits and accessories . Dull or damaged bits have a greater tendency to bind in the workpiece.
When removing the bit from the tool avoid contact with skin and use proper protective gloves when grasping the bit or accessory . Accessories may be hot after prolonged  use. Check to see that keys and adjusting wrenches are removed from the drill before switching the tool “ON” . Keys or wrenches can fly away at high velocity striking you or  a bystander.
Do not run the drill while carrying it at your side . A spinning drill bit could become entangled with clothing and injury may result.
GFCI and personal protection devices like electrician’s rubber gloves and footwear will further enhance your personal safety.
Do not use AC only rated tools with a DC power supply . While the tool may appear to work, the electrical components of the AC rated tool are likely to fail and create a hazard to the operator.
Keep handles dry, clean and free from oil and grease . Slippery hands cannot safely control the power tool.
Develop a periodic maintenance schedule for your tool . When cleaning a tool be careful not to disassemble any portion of the tool since internal wires may be misplaced or pinched or safety guard return springs may be improperly mounted . Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.
Risk of injury to user. The power cord must only be serviced by a Factory Service Center or Authorized SKIL Service Station.

SYMBOLS

Safety Symbols
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and  understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention  measures.
WARNING
Be sure to read and understand all safety instructions in this Owner’s Manual, including all safety alert symbols such as “DANGER,”   “WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed below may result in electric shock, fire, and/or serious personal injury.

The definitions below describe the level of severity for each signal word. Please read the manual
and pay attention to these symbols.

****| This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
| DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
| WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
| CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages
These inform the user of important information and/or instructions that could lead to equipment or other property damage if they are not followed. Each message is  preceded by the word “NOTICE”, as in the example below:
NOTICE: Equipment and/or property damage may result if these instructions are not followed.
WARNING
The operation of any power tools can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation,  always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend a Wide Vision Safety Mask for use over eyeglasses or  standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1.
IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you  to operate the tool better and safer.

Symbol Name Designation/Explanation
V Volts Voltage (potential)
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
kg Kilograms Weight
min Minutes Time
s Seconds Time
0 Diameter Size of drill bits, grinding wheels, etc.
no No load speed Rotational speed, at no load
n Rated speed Maximum attainable speed
…  /min Revolutions or reciprocation per minute Revolutions, strokes,

surface speed, orbits, etc. per minute
0| Off position| Zero speed, zero torque…
1,2,3,…| Selector settings| Speed, torque or position settings. Higher number means greater speed
| Infinitely variable selector with off| Speed is increasing from 0 setting
| Arrow| Action in the direction of arrow
| Alternating current| Type or a characteristic of current
| Direct current| Type or a characteristic of current
| Alternating or direct current| Type or a characteristic of current
| Class II tool| Designates Double Insulated Construction tools.
| Earthing terminal| Grounding terminal
| Li-ion RBRC seal| Designates Li-ion battery recycling program
| Ni-Cad RBRC seal| Designates Ni-Cad battery recycling program
| Read manual symbol| Alerts user to read manual
Symbol| Designation/Explanation
---|---
| This symbol designates that this tool is listed by Underwriters Laboratories.
| This symbol designates that this tool is recognized by Underwriters Laboratories.
| This symbol designates that this tool is listed by Underwriters Laboratories, to United States and Canadian Standards.
| This symbol designates that this tool is listed by the Canadian Standards Association.
| This symbol designates that this tool is listed by the Canadian Standards Association, to United States and Canadian Standards.
| This symbol designates that this tool is listed by the Intertek Testing Services, to United States and Canadian Standards.
| This symbol designates that this tool complies to NOM Mexican Standards.

GET TO KNOW YOUR HAMMER DRILL

Hammer DrillSKIL HD182001 Hammer Drill - Figure 1

SPECIFICATIONS

General

Model No.| HD182001
Chuck size and type| 1/2” (13mm) Keyed
RPM (No-load speed)| 0~3000/min

OPERATING INSTRUCTIONS

WARNING
Disconnect the plug from the power source before any assembly, adjustments or accessory changes. Such preventive safety measures reduce the risk of starting the tool accidentally.
Variable-Speed Trigger Switch
Your tool is equipped with a variable-speed trigger switch. The tool can be turned “ON” or “OFF” by squeezing or releasing the variable-speed trigger switch. The speed can be adjusted from the minimum to maximum nameplate RPM, according to the pressure you apply to the trigger.
Apply more pressure to increase the speed and less pressure to decrease speed (Fig. 1).
“Lock-On” Button
The “Lock-On” button, located in the handle of your tool, allows for continuous operation at a maximum RPM without squeezing the trigger (Fig. 1).
TO LOCK TRIGGER “ON”: squeeze the variable-speed trigger, depress the lock-on button, and release the trigger.
TO UNLOCK THE TRIGGER: squeeze the variable-speed trigger and release it without depressing the “Lock- On” button.
WARNING
If the “Lock-On” button is continuously depressed, the trigger cannot be released.

Reversing Button
The reversing button is located above the trigger switch and is used to reverse the rotation of the bit. For forward rotation, move the button to the far left. For reverse  rotation, move the button to the far right (Fig. 2).
NOTICE: Do not change the direction of rotation until the tool comes to a complete stop.
Changing the direction of rotation while the chuck is rotating can cause damage to the tool.

Chuck Key & Storage Area
Your tool is equipped with a chuck key that is conveniently located on the cord protector, where it is always handy and unlikely to get lost or misplaced (Fig. 1).

Inserting Bit
For small bits, open the jaws enough to insert the bit up to the flutes. For large bits, insert the bit as far as it will go. Center the bit as you close the jaws by hand. This  positions the bit properly, giving maximum contact between the chuck jaws and the bit shank.
To tighten chuck, insert the key into each of the three key holes in succession and firmly tighten them clockwise. The chuck can be released by using one hole only (Fig. 3).

Auxiliary Handle
The auxiliary handle will provide additional control, support, and guidance for the tool. The handle is adjustable to any position around the 360° front housing collar.
To mount the auxiliary handle, rotate the lower portion of the hand grip counter-clockwise to loosen it. Then push upward on the thumb grip provided and slide the handle  completely over the front housing collar.
To adjust, push upward on the thumb grip, move the handle to the desired position, and securely tighten the lower portion of hand grip clockwise (refer to Fig. 1).

Depth Gauge
The drilling depth can be pre-set and/or repeated by using the depth gauge.
Setting the depth: After the auxiliary handle is installed, make sure that the bit has been fully inserted into the chuck before setting the depth gauge.
To adjust the depth, rotate the lower portion of the hand grip counter- clockwise to loosen the depth gauge, slide the depth gauge to the desired position, and securely tighten  hand grip clockwise (Fig. 1).

Drill/Hammer-Drill Selector Switch
The selector switch allows the tool to be set for various drilling/hammer drilling applications.
Move the selector switch right or left depending on applications, as described below (Fig. 1).
CAUTION
Do not operate the selection switch until the tool has come to a complete stop. Shifting during chuck rotation can cause damage to the tool.
Drill-only action: For drilling in woods, metals, plastics, or other non- concrete materials.
Drill with hammer action: For drilling in masonry, asphalt, tile, or other similar hard materials.

Operating Tips
You will extend the life of your bits and do neater work if you always put the bit in contact with the work before pulling the trigger. During operation, hold the tool firmly  and exert light, steady pressure. Too much pressure at low speed will stall the tool. Too little pressure will keep the bit from cutting and cause excess friction by sliding over the surface. This can be damaging to both the tool and the bit.

Drilling with Variable Speed
The variable-speed feature eliminates the need for center punches in hard materials. The variable-speed trigger allows you to slowly increase the rotation speed. By using a  slow starting speed, you are able to keep the bit from “wandering”. You can increase the speed as the bit “bites” into the work by squeezing the trigger.
Drill Bits
Always inspect drill bits for excessive wear. Use only bits that are sharp and in good condition.
TWIST BITS: Available with straight and reduced shanks for wood and light-duty metal drilling.
Twist bits may overheat unless pulled out frequently to clear chips from flutes.
HIGH-SPEED BITS: CUT faster and last longer on hard materials.
CARBIDE TIPPED BITS: Used for drilling stone, concrete, plaster, cement, and other unusually hard nonmetals. Use continuous, heavy feed pressure when employing  carbide tip bits.
Drilling Wood
Be certain that the workpiece is clamped or anchored firmly. Always apply pressure in a straight line with the drill bit. Maintain enough pressure to keep the drill “biting”.
When drilling holes in wood, twist bits can be used. Twist bits may overheat unless pulled out frequently to clear chips from flutes.
Use a “back-up” block of wood for work that is likely to splinter, such as thin materials.
You will drill a cleaner hole if you ease up on the pressure just before the bit breaks through the wood. Then complete the hole from the back side.
Drilling Metal
There are two rules for drilling hard materials. First, the harder the material, the greater the pressure you need to apply to the tool. Second, the harder the material, the slower  the speed you should use. Here are some tips for drilling in metal:

  • Lubricate the tip of the bit occasionally with cutting oil, except when drilling soft metals such as aluminum, copper, or cast iron.
  • If the hole to be drilled is fairly large, it’s often faster in the long run to drill a smaller hole first, then enlarge it to the required size with a larger bit.
  • Maintain enough pressure to assure that the bit does not just spin in the hole. This will dull the bit and greatly shorten its life.

Drilling Masonry
Use carbide-tipped masonry bits for cinder block, mortar, common brick, soft stone, and other masonry materials. The amount of pressure to be used is dependent upon the  type of material being drilled. Soft materials require less pressure, while the hard materials need more pressure to prevent the drill bit from spinning.

MAINTENANCE

Service
WARNING
To avoid accidents always disconnect the tool from the power supply before cleaning or performing any maintenance.
WARNING
Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard . We recommend  that all tool service be performed by a SKIL Factory Service Center or Authorized SKIL Service Station.

Tool Lubrication
Your SKIL tool has been properly lubricated and is ready to use. It is recommended that tools with gears be re-greased with a special gear lubricant at every brush change.
Carbon Brushes
The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend that the  brushes be examined every two to six months. Only genuine SKIL replacement brushes specially designed for your tool should be used.
Bearings
Bearings that become noisy (due to heavy load or very abrasive material cutting) should be replaced at once to avoid overheating or motor failure.
Cleaning
WARNING
To avoid accidents, always disconnect the tool from the power supply before cleaning or performing any maintenance . The tool may be cleaned most effectively with  compressed dry air. Always wear safety goggles when cleaning tools with compressed air.
Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.
CAUTION
Certain cleaning agents and solvents damage plastic parts . Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household  detergents that contain ammonia.
Storage
Store the tool indoors in a place that is inaccessible to children. Keep away from corrosive agents.

EXTENSION CORDS

WARNING
If an extension cord is necessary, a cord with adequate size conductors that is capable of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3-wire extension cords that have 3-prong plugs and receptacles.
NOTEICE: The smaller the gauge number, the heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT ALTERNATING CURRENT TOOLS

Tool’s Ampere Rating Cord Size in A.W.G Wire sizes in mm2
Cord length in feet Cord length in meters
25 50 100
3-6 18 16
6-8 18 16
8-10 18 16
10-12 16 16
12-16 14 12

TROUBLE SHOOTING

Problem Cause Remedy
Tool will not start. 1.Power cord is not plugged in.

2.Power source fuse or circuit breaker is tripped.
3.Cord damaged.
4.Burned out switch.| 1.Plug tool into a power source.
2.Replace the fuse or reset the tripped circuit breaker. (If the product repeatedly causes the circuit or fuse to trip/blow, discontinue use immediately and have the tool serviced by an Authorized SKIL Service Center or Service Station.)
3.Inspect the cord for damage. If damaged, have the cord replaced by an Authorized
SKIL Service Center or Service Station.
4.Have the switch replaced by an Authorized SKIL Service Center or Service Station.
Tool does not come up to speed.| 1.Extension cord has insufficient gauge or is too long.
2.Low house voltage.| 1.Replace with adequate extension cord (Refer to the part of “EXTENSION CORDS”).
2.Contact your electric company.
Excessive vibration.| 1.Accessory being used is bent of damaged.
2.Accessory being used is not secure in chuck.| 1.Discard and replace with new accessory.
2.Reference the “Inserting Bit” section of manual.
Accessory binds, stalls motor or kicks back when drilling.| 1.Damaged accessory.
2.Incorrect accessory for drill/ hammer drill speed.| 1.Discard and replace with new accessory.
2.Use properly rated accessory as indicated by accessory manufacturer.

LIMITED WARRANTY OF SKIL CONSUMER PORTABLE, HD, SHD AND MAG HEAVY DUTY POWER TOOLS
Chervon North America (“Seller”) warrants to the original purchaser only, that all SKIL consumer portable, HD, SHD and MAG Heavy Duty power tools will be free from  defects in material or workmanship for a period of one year from date of purchase. SKIL consumer portable power tool models will be free from defects in material or  workmanship for a period of ninety days if the tool is used for professional use.
SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and, to the extent permitted by law, any warranty or condition  implied by law, shall be the repair or replacement of parts, without charge, which are defective in material or workmanship and which have not been misused, carelessly  handled, or misrepaired by persons other than Seller or Authorized Service Station. To make a claim under this Limited Warranty, you must return the complete product,  transportation prepaid, to any SKIL Factory Service Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations, please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW  BLADES, SANDING BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.
ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE YEAR FROM DATE OF PURCHASE. SOME STATES IN THE U.S., SOME  CANADIAN PRO V INCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT  APPLY TO YOU.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY  FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO  NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION  MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO  STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY  COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL DEALER OR IMPORTER.

© Chervon North America, 1203 E. Warrenville Rd, Naperville, IL 60563.
05/20

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals