SKYLINK WB-550 Garage Door Opener Installation Guide
- June 13, 2024
- SKYLINK
Table of Contents
P/N: 101Y553-002
Garage Door Opener Quick
Programming Guide
Post-Installation Wiring
-
Re-connect the wires of the safety beam sensor to the Atoms opener. Push in tab with a flat head screwdriver and Insert the wires.
-
Re-connect the wires of the wall console to the Atoms opener. Push in tab with a flat head screwdriver and insert the wires.
On Ground Programming (From the Wall Console)
-
Connect the opener to an approved power source. The dot in the LED display stays on.
-
Press and hold [ ****] button on the wall console for 5 seconds until the LCD display shows the number 1″ and up and down arrows are flashing.
-
Press the [ ] button until the door is in fully open position.
-
Press the [ ] button to confirm the door position.
-
The LCD Display will show the number “2”.
-
Press the [ ] button until the door is in fully closed position.
-
Press the [ ] button again to confirm.
-
The LED light will flash 3 times when the travel limit settings are completed.
-
The LCD Display will show the number “3′.
-
Press the ( ) button to open the garage door. The flashing ‘X will change to solid.
-
The LED light will flash 3 times again when the door is fully opened.
-
The LCD Display will show the number ‘C.
-
Press the [ ] button to close the garage door. The flashing ‘4’ will change to solid.
-
The garage door opener will beep once when door is fully closed and the display will show “F”.
-
Press the [ ] button again to confirm.
-
The LCD Display will flash the remote icon.
-
Program a Remote: Within 2 minutes, press any button on the remote that you would like to program to the opener.
Program a Wireless Keypad:
Within 2 minutes, activate the keypad by entering:
a. Pin code [default 0 0 0 0] plus # for single door operation.
b. Pin code [default 0 0 0 0] plus [ft] plus [Door No) for multiple door operation.
Enable the multiPle-door operation mode:
Enter the pin code plus (1) plus (9) plus (#1). -
The garage door opener will beep if remote is successfully programmed and the flashing remote icon will change to solid.
-
If you want to erase all the remotes, press and hold the [ ) button for 5 seconds until you see “E”.
-
If you need to program additional remote, press [ ] button, then refer to step 18. After you’ve programmed all remotes, press [ ] button.
-
The LCD Display will show the time setting.
-
Press the[ ] / [ ] buttons to set the hour to the current time; then, press [ ] to confirm.
-
Press the [ ]/ [ ] buttons to set the minute to the current time; then, press [ ] to confirm.
-
The LCD Display will show the remote lock time setting.
-
Press the [ ]/ [ ] buttons to set hour; then, press [ ]o confirm.
-
Press the [ t 1( 11 buttons to set minute; then, press [ ] to confirm.
-
The LCD Display will show the remote unlock time setting.
-
Press the[ ] 1/ [ ] buttons to set the hour; then, press [ ] to confirm.
-
Press the [ ]/ [ ] 1 buttons to set the minute; then, press [ ] to confirm.
-
On-ground programming is completed.
Operation
1. Wall Console
Press the [ ] button to open/close the garage door opener.
2. Remote
To open/close the opener with remote control, press the button that is
programmed to the opener.
3. Keypad
3.1 Single Door Operation Enter the PIN code plus [#) Example: 1 2 3 4 #
3.1 Multiple Doors Operation Enter the PIN code plus [4] plus [Door No.)
Example: 1 2 3 4# 1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>