Memphis Audio MXASB20V2 Bluetooth Soundbar Speaker Installation Guide

: June 13, 2024
: MEMPHIS AUDIO

Table of Contents

Memphis Audio MXASB20V2 Bluetooth Soundbar Speaker
Introduction
FEATURES
SPECIFICATIONS
CONTROLS
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING
WARRANTY
FAQs
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Memphis Audio MXASB20V2 Bluetooth Soundbar Speaker

Memphis Audio-MXASB20V2-Bluetooth-Soundbar-Speaker-product

Introduction

READY TO TURN IT UP? READ THIS FIRST!

Memphis Audio built a 50 year legacy in the audio industry engineering the highest quality products to produce the best possible listening experience for our fans and loyal supporters. To fully appreciate our products we recommend taking the time to read and follow the instructions in this manual. As always, we recommend all installations and service be performed by an authorized Memphis Audio dealer

TIP
For optimal performance, Memphis recommends using only Memphis Connection accessories. Outfitting .-” 1 … : (!J• your system with properly sized Memphis Connection wire and accessories will dramatically boost your , ,o, listen in ex erience and increase the durabilit of your Memphis Audio products.

The Memphis MXASB20V2 Sound bar is designed to make it easy to bring Memphis sound to virtually any vehicle. The easy to install, all in one unit is transforms your Bluetooth enabled device into the controls for your entire Audio experience. The multiple mounting options allow the MXASB20V2 to fit on nearly any UTV, Boat, golf cart or anything with a bar to mount it on. The MXASB20V2 was designed to be resistant to the outdoor elements, so get ready to enjoy that Memphis Sound wherever you are!

FEATURES

Built in Bluetooth receiver
Passive radiator for enhanced mid bass
Resistant to water and elements
Dual adjustable clamp fits bars 1″-2.5″ tubes
Self powered Plug S Play for quick installation
AUX input
2-Channel output

SPECIFICATIONS

6 Speaker system- Q x 3″ speakers and 2 x 1″ tweeters
Total Power: 200 Watts
Dimensions 21.3″ x 3.5″ x 3.9″
Clamp Fit: 1.25″-2.75″ Tube Mounts

CONTROLS

Bluetooth pairing
Hold the power button to turn the unit on. The indicator light will begin flashing blue. Go to your device and search for “Memphis SB2DV2” and click connect. The blue light will stay solid bluejwhen connected.

Bluetooth Operation

Power Button: Hold for power on/off. Quick press to select between Bluetooth and Auxin modes
Play Pause: Pauses and Plays the music. [Mutes music when in Aux-in mode]
Track Forward/Back: Skips tracks forward and back
V+/V-: Controls the volume of the internal amplifier
Status light: Flashes Blue when in Bluetooth Discovery mode. Solid blue when connected to a device. Solid green when in AUXin mode.

INSTALLATION INSTRUCTIONS

Wiring
The MXASB20V2 can be used with any 12-volt battery and can be mounted to a variety of bars using the included hardware. The unit has two wires in its wiring pigtail. The red wire [constant 12v], should be directly connected to the vehicles positive battery terminal, the black wire [chassis ground] should be connected directly to the vehicle’s chassis where paint has been removed or the negative terminal on the battery.

Optional Wiring

The green female 3.5mm jack is to be used for and optional Auxiliary input. You can use this jack to connect any audio device via 3.5mm jack.
The white female 3.5mm jack is a 2.5v low level audio out designed to drive external amplifiers. This allows the
MXASB20V2 to be used as the main source while adding more audio components to your system

MOUNTING

Take Ill mm bolt with lock washer and place it through bottom of clamp and slightly thread into Dove tailed piece.
Slide assembly into one of the three dove tail recessed areas placing the unit at the desired angle.
Tighten bolt to securely hold bracket in place.
Repeat this step for both included brackets. Both brackets must be used during installation.
Use bracket top half and tighten down over bar using the four included bolts, two per clamp.
Tighten until the unit is secure.
Connect wires to power, ground, and optional Aux-in our Audio out

Memphis Audio-MXASB20V2-Bluetooth-Soundbar-Speaker-
fig-1

TROUBLESHOOTING

No Output:

Confirm all wiring is firmly connected.
Both +12V must have +12 Volts present and GND must be connected to chassis’ ground or to the negative battery terminal.
Confirm the signal source is connected via Bluetooth or the auxiliary cable is connected to both the source and the MXASB20V2

Weak Output
Check Bluetooth device volume level.

Unwanted Noise

Whine that increases and decreases with engine speed -confirm the Amp S Source unit are grounded properly.
Clicking or popping noise at a rate that follows engine speed -this is often induced by the vehicles ignition system.
Confirm that the vehicle is equipped with resistor spark plugs and wires. The ignition system may need service.
Noise can be caused by routing speaker input wires too close to the light wires and other accessory wires in the vehicle. Re-route wires to avoid unwanted interference.

Red LED is Illuminated

Speaker or wire is shorted
Battery voltage too low
Battery voltage too high· Amplifier has overheated due to improper ventilation
If above steps do not improve/reduce noise, the system should be checked by a professional audio installer at a Memphis Authorized Dealer.

WARRANTY

Memphis Xtreme Audio MXASB20V2 Limited Warranty
This product has a one year warranty from the date of purchase for defects in material or workmanship. This warranty will be extended to 2 years when installed by a Memphis authorized dealer using Memphis Connection products. The warranty is void if the product has been physically damaged by improper usage or abuse. If repairs are attempted outside of a Memphis Audio facility, the warranty is void. This warranty is limited to the original retail purchaser and does not cover any expenses incurred in the removal or re- installation of the product. This warranty does NOT apply to product exterior and cosmetics. Memphis Audio disclaims any liability for incidental or consequential damages caused by product defects. Memphis Audio liability will not exceed the purchase price of the product and the warranty period specified.

What is NOT covered under warranty

Damage due to improper installation
Damage through negligence, misuse, accident or abuse. (Repeated returns for the same damage may be abuse]
Product damaged in accident and/or due to criminal activity
Service performed by anyone other than Memphis Audio
Subsequent damage to other components
Any cost or expense related to the removal or re-installation of product
Products with tampered, missing , altered or defaced serial numbers/labels
Freight damage
The cost of shipping product to Memphis Audio
Return shipping on non-defective items
Any product not purchased from an authorized Memphis Audio dealer
Some states do not allow the exclusion or limitation of incidental or consequential damages. The above limitations or exclusions may not apply to you.

This warranty gives you specific rights, you may have other rights which vary from state to state. If warranty service is required, a return authorization number is required to return the product to Memphis Audio. Warranty shipments to Memphis Audio are the responsibility of the purchaser. Pack the product carefully in the original carton if possible Memphis Audio will not be responsible for damages incurred in shipment or due to improper packaging materials used by the purchaser. If determined to be within warranty your product will be repaired or replaced at the discretion of Memphis Audio.

WARNING

For your safety, always inspect the mounting location carefully to ensure you are not drilling into any electrical, hydraulic, fuel or fluid lines.
Always check your speaker load with a multi-meter before connecting the amplifier.
Connecting any speaker load lower than the rated impedance of the amplifier will result in damage to the amplifier.
Damage of this nature is NOT covered under warranty. Please pay close attention to what connections are made to the amplifier.

Memphis Audio