elk Home 57027-4 Diffusion 4 Light 24 inch Oil Rubbed Bronze Installation Guide

: June 13, 2024
: elk HOME

Table of Contents

Safety Warnings
Installation Instructions
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

elk Home 57027-4 Diffusion 4 Light 24 inch Oil Rubbed Bronze

elk Home 57027-4 Diffusion 4 Light 24 inch Oil Rubbed
Bronze

Safety Warnings

WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.

WARNING:
This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Before assembly, remove all parts and part packages from box. If anything is missing, please contact the retailer from which the product was purchased.

ITEM#: 57027/4

Installation Instructions

Carefully pull house wires down out of junction box so house wires are easily accessed to connect fixture wires.
If screw collar loop (W) is already attached to mounting bracket (A), proceed to Step 3. To assemble screw collar loop (W) to mounting bracket (A): Hold mounting bracket (A) so head of ground screw is pointing down towards floor. Hold threaded pipe so two hexnuts already attached to threaded pipe (E) are pointing down towards floor. From side of mounting bracket with ground screw head, screw short end of threaded pipe (E) into hole in center of mounting bracket (A) until hexnut on threaded pipe (E) touches mounting bracket. Thread hexnut (V) onto end of threaded pipe (E). Tighten hexnut (V) to secure threaded pipe (E) to mounting bracket (A). Thread screw collar loop (W) onto end of threaded pipe pointing down towards floor. Tighten screw collar loop up against hexnut on threaded pipe (E).
Place mounting bracket (A) up against junction box. Screw collar loop (E) should be pointing down towards floor. Align each slot in mounting bracket (A) with each hole in junction box.
Thread one junction box screw (B) into each slot in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box.

CAUTION: Make sure house wires are still easily accessible.
DO NOT pinch wires between mounting bracket and ceiling.
Lower shade (K) over fixture body (O).
Screw hub (G) onto top of center stem (M).
Carefully push fixture wires from top of fixture body (O) up through bottom of center stem (M). Pull fixture wires out of top of hub (G) on top of center stem (M). Pull fixture wires taut. Screw bottom of center stem (M) onto top of fixture body (O).
Push fixture wires up through bottom of loop (P). Pull fixture wires taut. Screw bottom of loop (P) onto threaded pipe protruding from top of hub (G).
Lower one glass shade (R) down over each socket. Slip socket cover (T) over each socket.
Thread socket ring (X) onto each socket. Tighten socket rings (X) to secure glass shades (R) in place. DO NOT over tighten.
Screw recommended bulbs (E26 Edison bulb type, not included) into sockets. Verify correct bulb wattage marked on socket of fixture.
WARNING: DO NOT exceed maximum bulb wattage.
Hold one arm (L) so threaded end of arm (L) is at the bottom. Slip threaded end of arm (L) through one bracket on inside of shade (K). Screw threaded cap (N) onto threaded end of arm (L). DO NOT tighten threaded cap (N). This will be done after all arms (L) are assembled.
Slip hook at top of arm (L) through one small loop on side of hub (G).
Repeat steps 12 and 13 to assemble remaining arms (L) to fixture.
After all arms (L) have been attached, completely tighten all threaded caps (N).
Determine desired hanging height of fixture. Cut chain (H) to length to achieve desired.
Slip chain link at end of chain (H) onto loop (P).
Weave fixture wires through chain links, skipping every other chain link.
Slip threaded ring (F) down over end of chain (H) with fixture wires.
Position canopy (D) so outside of canopy is pointing down towards fixture. Slip hole in canopy (D) over end of chain (H).
Strip 3/4” of insulation from ends of fixture wires.
Raise fixture up to ceiling. Attach link at end of chain (H) to screw collar loop (W).
Carefully push fixture wires up through hole in screw collar loop (W) attached to mounting bracket (A) and out end of threaded pipe inside junction box. Carefully pull fixture wires so they are easily accessible to connect to house wires.
Slightly loosen ground screw on mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire. Twist end of fixture ground wire and end of house ground wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.
Connect Supply (House) Ground Copper Wire to:
- Bare Copper Wire or,
- Bare Silver Wire or,
- Green Insulated Wire
Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.
Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.
Carefully push all wires and wire nuts into junction box.
Connect Black Lead Supply (House) Wire to:| Connect White Neutral Supply (House) Wire to:
---|---
Black Wire or,| White Wire or,
Parallel Cord (Round and Smooth) or,| Parallel Cord (Square and Ridged) or,
No printed words on wire insulation or,| Printed words on wire insulation or,
Insulated Wire (other than green) with Copper Conductor.| Insulated Wire (other than green) with Silver Conductor.
*When parallel wire (SPT 1 & SPT 2) is used: The lead wire is round in shape or smooth. The neutral wire is square in shape or ridged.

Installation Instructions

Raise canopy (D) up to ceiling. Pass hole in canopy (D) over screw collar loop (W). Position canopy (D) up against ceiling.
Raise threaded ring (F) up to canopy (D). Screw threaded ring (F) onto screw collar loop (W). Tighten threaded ring (F) to secure fixture to ceiling.