VEVOR L4040 Desktop Laser Engraver User Manual

: June 13, 2024
: VEVOR

VEVOR L4040 Desktop Laser Engraver User Manual

Warning

Strictly prohibit laser radiation of the eyes!
Strictly prohibit watching laser without wearing protective glasses!
Strictly prohibit using by children!
Strictly prohibit using this machine unattended!
Scan for assemble video

Parts List

4040 Parts List

02| Aluminum profile (X)| 2040*480mm| 2|

03| Aluminum profile (Y)| 2020*555mm| 2|

Parts List

04| L-shaped connector| L-shape| 4|

05| Acrylic plate B for X-Part| ——| 1|

06| Leg| ——| 4|

07| Fixed wire block| ——| 1|

08| Synchronous belt| 2GT，length 620mm| 2|

09| Inner hexagon screw| M5*8| 10|

10| Inner hexagon screw| M5*10| 1|

11| Set screw| M5*6| 12|

12| Square nut| M5| 12|

13| Manual nut| M5| 4|

14| Ship nut| M5-10| 3|

15| Control board package| VIGO-13| 1|

16| Wiring harness and protective pipe| ——| 1Set| /
17| Cable ties| ——| 8|

18| Power supply and power line| 12V DC| 1Set|

19| Inner Hexagon Wrench| 4/2.5/2mm| 1Set|

20| Nut Wrench| 8#| 1
21| USB cable| ——| 1|

22| Protective glass| ——| 1|

23| Non-slip mat| ——| 1| /
24| Instruction manual| ——| 1| /
Laser package（Optional）
L1| Laser kit| Optional| 1Set| /
M1| Inner hexagon screw| M3x6| 4|

Control board package（15）
C1| Control board| VIGO-13| 1| /
C2| Acrylic plate for control board A| ——| 1|

C3| Acrylic plate for control board B| ——| 1|

C4| Column| Φ3*7| 4|

C5| Inner hexagon screw| M3×18| 4|

C6| Nut| M3| 4|

Machine Assembly

Laser Installation

Cable connection

Download and run the engraving control software “VevorWorks”

Open our website www.vevorengraver.com.

Find the control software for L4040, then click to download it to your computer.

Green software doesn’t need to be installed. Decompress the file you downloaded just now. The software running OS is Win7 Win8 and Win10.

Open the fold and double-click the VevorWorks.exe file to run the engraving software. The OS may prompt that the software will use the network, please click OK (some computer systems do not prompt, if the software cannot use the network, please allow it manually in the firewall setup).

In addition, the machine also supports the engraving software of the third- party standard GRBL, such as LaserGrbl, LightBurn, etc

Connect VevorWorks software and laser engraving machine

Long press the power button on the machine panel to turn on it. There are three ways to connect engraving software and the machine.

USB-Serial Connection

Connect the USB-Serial cable to both control board and computer. In general, Win10 can automatically identify the device. Win7 or other OS may need to install driver manually. Please double click ch341ser.exe to install the driver if necessary. Click Connect on top left corner of VevorWorks, SERIAL-ON will be displayed in the title bar, indicating that the connection is successful.

Adjust focus

Please use the focal length measuring piece to adjust the module height so that the distance from the lower edge of the module protective cover to the engraved object is equal to the height of the measuring piece.

Open or input the engraving content and adjust the engraving parameters

Cable connection

Engraving content can be opened at the top of the software image or gallery, or edit the engraving text. Set the start location of engraving and adjust the size of engraving. Select one of the engraving modes. There two engraving mode, line mode and point mode, which can respectively engrave black-and-white images, grayscale images and outlines. (only line engraving is supported for outline, please use outline when cutting objects.)
Cable connection

Set engraving parameters. There are four engraving parameters that can be set. These parameters will affect the engraving speed and engraving effect. It is necessary for you to understand the function of these parameters and adjust them according to different engraving materials and contents.

Line engraving speed: Set the engraving speed (only valid for line engraving mode).
Note that the set speed may not be reached when the image is too small or the dot distance is too dense.
Maximum laser power: Set the maximum laser power, which is the laser power when the maximum gray level (i.e. all black) in the dot matrix gray mode and line scan gray mode and the laser power in the Binary (black and white) engraving mode. The unit is the percentage of the installed laser full power.
Engraving point distance: set the precision of dot matrix engraving or line scanning engraving, and the number of lines or points per millimeter.
Time of dot engraving: Set the engraving time of each dot. The unit is millisecond. According to the power of the laser module and engraving material, we generally recommend to set about 1ms to 5ms.

Preview the engraving range and start engraving

Click Range preview to confirm the position and range of engraving. Click Start and wait for the engraving to be completed.

Introduction of software interface function

Cable connection

Instructions for Laser

Please wear the protective glasses before operating the laser!

When all the connections are completed, turn on the power, and the laser is standby for working. The indicator light on the top of the laser is continuous lighting at this time.

Turn on the weak light and adjust the focal length

Please lay the materials to be carved flat under the laser.
Please turn on the weak light in the engraving software or press the weak light switch on the top of the laser module. Then the red light will flash and the weak light on. Laser spots can be seen on the materials at this time. Adjust the height of the module, when the laser spots are smallest and clearest, it is the optimum state for laser engraving. Or use the focal length measuring piece to adjust the module height so that the distance from the lower edge of the module protective cover to the engraved object is equal to the height of the measuring piece.

It is important to understand that this weak light switch on the top of the laser module is not controlled by engraving control software. So be sure to switch back to normal (make sure that weak light is off) before you start engraving.

Notice

The shape of all parts above in this description is only as a sign. There may be a difference between the actual parts and the parts in the installation instructions. Please refer to the shape of the actual parts purchased.
Please pay attention to the sequence of the installation steps to avoid repeated disassembly.
Make sure hibernate and sleep are disabled when working long hours. This feature may cause the laser to continue to glow out of control, and burning on the table.

Update

3. Update

Our software will be updated continuously.

Please visit our website: www.vevorengraver.com for more new products and software.

Please be sure to download the VevorWorks for this machine.

Please refer to the Software Installation Manual for control software instructions.

Please contact us if you have any questions.

www.vevor.com

Contact: service@vevor.com
Call us:
(+626) 275-4507 (For USA)
(+44) 1173182739 (For Europe)
(+001) 626 275-4507 (For Other Countries)
Working Time: Mon-Fri 8:00am to 5:00pm
Powered by VEVOR 2022