Menumaster MSO35 Commercial Microwave User Guide

Menumaster MSO35 Commercial Microwave

INSTRUCTION

Quantity

Automatically adjusts preprogrammed cook cycle for cooking two of the same food items.

A/B Pad
Toggles selection between two sets of preprogrammed menu settings.

Time Entry
Cooking time can be changed for either manual entry or programming.

Power Level
Changes microwave power level for different stages of a cook cycle.

Stage
Users can program up to four different stages per keypad to combine power levels and time changes.

Program Save
Programs or settings can be changed and saved based on a user’s preference.

Oven Clearances

• Allow at least 7” (18 cm) of clearance around the top of the oven.
• Proper airflow around the oven cools electrical components. With restricted airflow, the oven may not operate properly and the life of electrical parts is reduced.
• There are no clearance restrictions between air discharge on the back of the oven and the back wall.
• Allow at least 1” (2.54 cm) around the sides of the oven.

Manual Operation

To cook food using a specific entered time and power level.

1. Open the oven door and place food in the oven. Close door.
2. Press the TIME ENTRY pad and enter the cooking time.
3. Press the POWER LEVEL pad to change the power level if desired.
   • For a lower microwave power, press pads 1 (for 10%) through 9 (for 90%)
   • Press the same number keypad again to change the power level to 100%
4. If stage cooking is desired, press the STAGE pad and repeat steps 2 through 4.
5. Press the START pad.
6. At the end of the cooking cycle oven beeps and shuts off. DONE displays.

USB Compatibility
A standard USB flash drive is compatible with the microwave oven, allowing the user to save preprogrammed settings to the flash drive rather than the oven.

1. The oven must be in READY mode. If not, open and close the door.
2. Open the oven door completely.
3. Insert a USB flash drive.
4. Press and hold the 5 keypad until “USB” appears on the display.
5. To transfer FROM the USB flash drive TO the oven, press the 1 pad.
   • Or to transfer programs TO the USB flash drive FROM the oven, press the 2 pad.
6. Push the START pad to begin the transfer.
   • The display will read, “Contacting USB card.”
   •  The display will then read, “Transferring data from USB to oven,” or vice versa
7. Once programming has been successfully transferred, the display will read, “Done – Loaded __ Programs.”
   • Shut the door to clear the display and begin a cooking cycle.

Preprogrammed Pads
To cook food using preprogrammed cooking sequences.

1. Open the oven door and place food in the oven. Close door.
   • To add an additional serving press QUANTITY pad.
   • The display will read, “DOUBLE.”
2. Press the desired pad.
3. The oven begins to cook.
4. At the end of the cooking cycle oven beeps and shuts off the DONE displays.

CLEAN FILTER

This oven displays CLEAN FILTER at user-defined intervals. When the message displays, ACP recommends cleaning the air filters thoroughly. Cleaning the air filter will not shut off the message. The message will stop displaying automatically after 24 hours. Depending on microwave use and environmental conditions, the filter may need to be cleaned more frequently.

Changing User Options
Options such as single or double-pad programming and beep volume can be changed to suit individual preferences.

To change options

1. Press firmly on a hidden pad located to the right of the STOP keypad
   • Pad is unmarked
   • The display remains blank when the hidden pad is pressed.
2. Press the PROGRAM SAVE pad.
   • The first user option will display. The oven is now in the options mode
3. Press the desired number pad to control changes in options.
   • See table on next page for options.
   • The current option will display
4. Press the same number pad again to disable or enable the setting.
   • Each time the pad is pressed, the option will change
   • Changes take effect immediately
   • To change additional options, repeat steps 3 and 4
5. Press PROGRAM SAVE to return to READY mode or open and close the oven door.

Programming Pads

1. READY must be in the display. If not, open and close the door.
2. Press the PROGRAM SAVE pad.
   • Programming mode begins
   • “Enter Program to Add/Review” is displayed
3. Press the desired number pad to be programmed.
   • The display will show all settings for the pad
   • The pad number that is being programmed is displayed beside the word ITEM
4. Press TIME ENTRY to program the amount of cooking time.
   • Enter desired cooking time by using numeric keypads
   • Maximum cooking time is 60 minutes
5. Press the POWER LEVEL to program the level of microwave power.
   • For a lower microwave power, press pads 1 (for 10%) through 9 (for 90%)
   • Press the numeric keypad for the desired level. Press the same keypad again to set the power level to 100%
6. When cooking two of the same food items, press the QUANTITY pad before a preprogrammed cook cycle. The oven will automatically adjust the program.
   • The display will read, “DOUBLE.”
   • To clear, open, and close the door or press the STOP pad
7. Press PROGRAM SAVE to save the program changes.
8. To discard changes, press STOP/RESET.

Programming Multiple Stages

Stage cooking allows consecutive cooking cycles without interruption. Up to four different cooking cycles can be programmed into a memory pad.

1. Follow steps 1-5 in the Programming Pads portion above.
2. Press the STAGE keypad.
   • This will begin programming for the next cooking stage
   • The display indicates the stage to be programmed
   • Enter cook time and power level as in steps 4 and 5
   • To enter another cooking stage for that pad, press STAGE again
   • The total cooking time limit is 60 minutes
3. When cooking two of the same food items, press the QUANTITY pad before a preprogrammed cook cycle. The oven will automatically adjust the program.
   • The display will read, “DOUBLE.”
   • To clear, open, and close the door press the STOPpad
4. Press PROGRAM SAVE to save programming and changes.
5. To discard changes, press STOP/RESET before pressing PROGRAM SAVE.

Top or Bottom Only Cooking

1. Push the POWER LEVEL pad.
2. Select and program the preferred microwave power.
3. If the POWER LEVEL pad is pushed a second time, the “Top Only” heating option will be selected and displayed.
4. f the POWER LEVEL pad is pushed a third time, “BottomOnly” heating is selected and displayed.
5. If the POWER LEVEL button is pushed a fourth time, the oven resets and both the top and bottom will heat.

Options utilisateur

1

Double Digit Entry

| Disabled

Enabled

| Allows 10 (0-9) preprogrammed pads

Allows 100 (00-99) preprogrammed pads

2

Manual Programming

| Disabled

Enabled

| Manual time entry/cooking not allowed

Manual time entry/cooking allowed

3

Reset on Door Open

| Disabled

Enabled

| Opening oven door does not reset oven back to READY mode

Opening oven door resets the oven back to READY mode

4

Key Beep

| OFF

ON

| Keys do not beep when pressed

Keys beep when pressed

5

Speaker Volume

| OFF LOW MEDIUM HIGH| Key beep volume OFF Key beep volume LOW

Key beep volume MEDIUM

Key beep volume HIGH

6

End of Cook Signal

| Solid Beep

3          Second Beep

4           Beeps Once

4 Beeps Repeating

| Done signal is a continuous beep until reset by the user

Done signal is a three second beep Done signal is four beeps continuously Done signal is four beeps, four times

7

Keyboard Active

| 15 seconds

30 seconds

60 seconds

120 seconds Always

| Keypad time entry window is 15 seconds Keypad time entry window is 30 seconds Keypad time entry window is one minute Keypad time entry window is two minutes Keypad time entry window is always active
0

Top or Bottom Cooking

| Disabled

Enabled

| Disables the use of top or bottom only cooking

Enables the use of top or bottom only cooking

Time Entry Pad

On-The-Fly Cook

| Disabled

Enabled

| Disables pushing any additional keypads during a cook cycle

Allows pushing additional keypads to add or change time in the middle of a cook cycle without stopping

X2 Pad

X2 Prompt

| Disabled

Enabled

| Disables X2 prompt

Enables X2 prompt

A/B Pad

A/B Menus

| Disabled

Enabled

| Disables A/B Menus

Enables A/B Menus

Power Level Pad

Return to Menu

| A

B

Last Selected

| Return to Menu A

Return to Menu B

Return to last selected menu

Stage Pad

Clean Filter Message (Frequency)

| Disabled Weekly Monthly Quarterly| Oven will not display CLEAN FILTER

Oven will display CLEAN FILTER every seven days

Oven will display CLEAN FILTER every 30 days Oven will display CLEAN FILTER every 90 days

Part No. 20151903 Printed in U.S.A. Original Instructions  For full product documentation visit: www.acpsolutions.com 2023 ACP, Inc.
225 49th Avenue Drive
Cedar Rapids, Iowa 52404 U.S.A.

References

• Home | ACP Solutions Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>