CRUX WVIFD-02 MyFord Touch Radio System Instructions
- June 13, 2024
- CRUX
Table of Contents
CRUX WVIFD-02 MyFord Touch Radio System
Product Information
The WVIFD-02 is a Wi-Fi audio/video interface designed for select Ford and
Lincoln vehicles manufactured from 2011 and onwards. It is compatible with
MyFord Touch Radio Systems. Please note that the vehicle must be equipped with
Factory A/V Input for
the kit to function properly.
The product is suitable for the following Ford vehicles:
- 2011 – 2015 Edge
- 2011 – 2015 Explorer
- 2012 – 2015 Focus
- 2013 – 2015 Focus ST
- 2013 – 2015 Escape
- 2013 – 2015 Fusion Hybrid
- 2013 – 2015 Fusion Energy
- 2013 – 2015 Taurus
- 2013 – 2015 C-Max Hybrid
- 2013 – 2015 C-Max Energy
Please note that Ford F-Series vehicles have a separate and specific Part Number: WVIFD-02F.
The product is also compatible with the following Lincoln vehicles:
- 2013 – 2015 MKS
- 2012 – 2015 MKT
- 2011 – 2015 MKX
- 2013 – 2015 MKZ
Activating the VIM (Video in Motion) feature may affect the GPS system, potentially causing delays in location updates.
The WVIFD-02 works with all MyFord Touch Radios. After installation, the radio system will go through a reboot process that may take up to 1 minute. It will then initialize and reload all previous settings, resuming the original radio display.
Parts Included:
- WVIFD-02 Interface (C-125)
- WVIFD-02 Interface (C-500)
- WVIFD-02 T-Harness
- WVI Wi-Fi Interface
- Instruction Manual
Precautions:
- Remove the negative side of the battery before installation to avoid short circuits.
- Avoid installing the interface near major components or the HVAC system to prevent damage or overheating.
- Do not disconnect the airbag connection behind the radio panel.
Product Usage Instructions
Installation Overview:
- Remove the factory display to access the factory connectors.
- Disconnect the 54-Pin connector from behind the display.
- Make the T-Harness connections behind the factory display. If the connectors do not match, please contact tech support.
- Connect both Interfaces to an 8-Pin connector without any specific orientation.
- Set the dip switches as needed on both interfaces. Refer to “Setting The DIP Switches” section for details.
The Wi-Fi Interface:
- Connect the 10-Pin Power and AV cable to the Wi-Fi interface.
- Connect the RED power lead to 12v and the BLACK wire to ground. An optional 12v output wire is provided from the interface if the vehicle does not provide 12v Acc 250ma.
- Screw on the Antenna to the interface and select the MODE of the system type you are connecting. Press once to toggle between iOS and Android Systems.
- Reset the system by pressing 1 second for a reset or holding for 5 seconds to restore factory defaults.
Important Note: Before connecting the interface to the harness, if the vehicle is equipped with Factory RVC (Rear View Camera), make sure Dip 2 is set to ON. Failure to do so will result in the loss of the factory rear-view camera. Contact tech support for assistance if needed.
COMPATIBLE RADIO SYSTEM: MyFord Touch Radio System*
- Important Note: Vehicle must be equipped with Factory A/V Input for the kit to function.
FORD
2011 – 2015 Edge
2011 – 2015 Explorer
2012 – 2015 Focus
2013 – 2015 Focus ST
2013 – 2015 Escape
2013 – 2015 Fusion Hybrid
2013 – 2015 Fusion Energy
2013 – 2015 Taurus
2013 – 2015 C-Max Hybrid
2013 – 2015 C-Max Energy
NOTE: Ford F-Series have a separate & specific Part Number: WVIFD-02F
LINCOLN
2013 – 2015 MKS
2012 – 2015 MKT
2011 – 2015 MKX
2013 – 2015 MKZ
Activating the VIM will effect the GPS System.(May cause delay in location
updates)
WORKS FOR ALL:
MyFord Touch Radios
NOTE: The radio system will go through a reboot process that may take up to 1 minute. It will initialize and re-load all previous settings. Once complete it will resume the original radio display.
We recommend reading this installation guide first before starting any work.
Following these instructions from “Start” to” Finish” will ensure a smooth and
hassle free installation. We offer telephone support M-F 9:00 AM – 5:00PM PDT
at 1 855-822-1348. We are here to help.
PARTS INCLUDED:
(1) WVIFD-02 Interface (C-125)
(1) WVIFD-02 Interface (C-500)
(1) WVIFD-02 T-Harness
(1) WVI Wi-Fi Interface
(1) Instruction
PRECAUTIONS
- Remove the negative side of the battery to avoid any short circuits during the installation.
- Do not install the interface near any major components or near the HVAC system. This may cause damage or overheating to the vehicle.
- Do not disconnect the airbag connection behind the radio panel.
PRELIMINARY:
Please read the entire manual before installing this interface.
INSTALLATION
THE AV INTERFACE:
- Remove the factory display to gain access to the factory connectors.
- Remove the 54-Pin connector from behind the display.
- Make the T-Harness connections behind the factory display. (if the connectors do not match please contact tech support)
- Connect both Interfaces to an 8-Pin connector. No orientation.
- Set the dip switches as needed on both interfaces. (See Setting The DIP Switches)
-
Connect the RED power lead to 12v and the BLACK wire to ground.
As an option we have provided a 12v output wire from our interface, as the vehicle does not provide 12v Acc 250ma. -
Screw on the Antenna to the interface and select the MODE of the system type you are connecting.
Mode: Press once to toggle between iOS and Android Systems.
Reset: Press 1 Second = Reset/ Hold 5 Seconds = To Factory Defaults
- Switch to the new AV input by using the SWC or a toggle switch.
- Test the interface, then re-install the display into the dash.
INSTALLATION OVERVIEW
SETTING THE DIP SWITCHES
-
Dip 1: Activates the Video In-Motion feature. The dip switch is the permanent solution for keeping the VIM unlocked.
The SWC/ Toggle Switch feature will be deactivated with it ON. Dip 2: If the vehicle has a factory Rear-View Camera, the installer MUST set DIP 2 to the “ON” position on the C-125 module only. Dip 3 & 4: Not used -
Dip 5: Place to the OFF position on both interfaces.
-
Dip 6: Place to the ON position on both interfaces.
Activating the VIM will effect the GPS System.
(May cause delay in location updates)
TROUBLE SHOOTING
- No video display while driving.
Make sure the dip switches are in the proper location.
ACTIVATE AND DEACTIVATE OPTION
Using the RIGHT HAND SIDE SWC buttons you can activate and deac-
tivate the video in-motion function. (ONLY WITH DIP SWITCH 1 OFF)
SETTING THE DIP SWITCHES DETAILS
PIN 1/ VIM CONTROL CONFIGURATION
| DIP# | C- 125 | C- 500 | RESULT |
|---|---|---|---|
| Dip 1 | OFF | OFF | User control of the VIM feature will be turned ON and OFF |
from the SWC
or Optional Toggle Switch
See instruction for SWC activation.
| |
Dip 1| ON| ON| VIM Permanently on. No control on SWC or Optional Toggle
Switch. Recommended for vehicles w/o factory GPS.
Dip 2| ON| OFF| If the vehicles is equipped with a factory rear-view camera.
---|---|---|---
Dip 2| OFF| OFF| If the vehicles is NOT equipped with a factory rear-view
camera.
Dip 3| OFF| OFF| Not Used.
Dip 4| OFF| OFF| Not Used.
Dip 5| OFF| OFF| CAN Termination.
Dip 6| OFF| OFF| CAN Termination.
CONNECTING TO THE WI-FI INTERFACE
SETTING UP YOUR DEVICE:
With the interface on and ready.
- On the new iOS 7 you can easily do the following:
- Swipe your finger from the bottom up on the iPhone or iPad.
- From the Quick Menu turn ON the Wi-Fi and connect to “HotSpot”.
- After connecting the Wi-Fi, from that same screen select the
- AirPlay item to connect to the interface.
- To turn on Mirroring, you will need to be connected to the interface and select the AirPlay item again, and turn on Mirroring option.
If your device doesn’t support the iOS 7:
- Settings > Wi-Fi > On
- Choose Network > “Hot Spot”
- After connected, double click the Home button to display your recently used apps.
- Select the AirPlay icon to begin to mirror. (Wi-Fi must be connected).
If no AirPlay icon, make sure your connected to Hot Spot
For the Android systems, make sure you switch the MODE on the interface
From your the Home screen, swipe down from the top of the screen to access the Screen Mirroring item and scan for the Hot Spot device. This can take up to 20 seconds.
Wi-Fi TROUBLESHOOTING
When exiting and coming back to the vehicle you may encounter a delay when re- connecting. If a separate Wi-Fi connection is made, you may need to manually reconnect.
MIRRORING:
The Mirroring connection uses a direct Wi-Fi connection to transfer the Audio
and Video from your device. This does not require a active network.
If your smartphone has the Screen Time Out, active on your phone, and your
phone display goes to sleep, you will no longer see the image on the screen.
Deactivate to avoid.
IMPORTANT NOTE:
Does Not support Netflix and Youtube on iOS System (APPLE) Devices due to
Restrictions placed by Apple.
The VCIP5 cable may be utilized for accessing these Apps (Sold Separately).
ANDROID System Devices are fully compatible with the above Apps.
SAFETY WARNING:
THIS INTERFACE IS DESIGNED TO ACTIVATE VIDEO IN-MOTION TO ALLOW THE PASSENGER
ACCESS TO THE ADDRESS INPUT WHILE THE VEHICLE IS IN-MOTION. THIS INTERFACE MAY
CAUSE AN ERROR WHEN SERVICED AT THE OEM DEALER. BE AWARE THAT MOST DEALERS
WILL ATTEMPT TO VOID THE MANUFACTURERS WARRANTY WHEN INSTALLING ANY AFTERMAR-
KET EQUIPMENT. IMPROPER USE OF THIS INTER-FACE BY THE DRIVER MAY RESULT IN
CITATION. DRIVER MUST KEEP FULL ATTENTION ON THE ROAD AND RESPONSIBILITY ON
THE SAFETY OF THEIR PASSENGERS.
COMPATIBLE FACTORY MYFORD TOUCH RADIOS
USING THE 8-PIN FOR GROUND
We recommend using the BLACK wire on the 8-Pin C-500 connector.
See picture below for where to tap.
OTHER SUPPORTED SWC
Documents / Resources
| CRUX
WVIFD-02 MyFord Touch Radio
System
[pdf] Instructions
WVIFD-02 MyFord Touch Radio System, WVIFD-02, MyFord Touch Radio System, Touch
Radio System, Radio System
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>