EPSON STI6290-D101 WLAN Bluetooth Module Instruction Manual
- June 13, 2024
- Epson
Table of Contents
EPSON STI6290-D101 WLAN Bluetooth Module
Product Information
- Product Name: WLAN / BT Module STI6290-D101
Regulatory Compliance Information:
- This device complies with Part 15 of the FCC Rules.
- For product available in the USA/Canada market, only channel 1~11 can be operated.
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
- The antenna must be installed such that 20 cm is maintained between the antenna and users.
- The transmitter module may not be co-located with any other transmitter or antenna.
Antenna Information:
| Antenna Type | Frequency Band (MHz) | Ant 1 Gain (dBi) | Ant 2 Gain (dBi) |
|---|---|---|---|
| Wi-Fi Antenna | 2400 ~ 2483.5 | 2.34 | 2.74 |
| 5150 ~ 5250 | 3.58 | 3.39 | |
| 5725 ~ 5850 | 5.29 | 4.50 | |
| Bluetooth Antenna | 2400 ~ 2483.5 | N/A | 2.74 |
Important Note:
Any deviation(s) from the defined parameters of the antenna trace, as
described by the instructions, require that the host product manufacturer must
notify EPSON of the change in antenna trace design.
Label of the end product: The host product must be labeled in a visible area with the following: Contains FCC ID: BKMAE-STI6290. The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This module is restricted to integration into hosts for indoor use only. OEM integrator has limited the operation channels in channel 1-11 for the 2.4GHz band.
Product Usage Instructions
- Ensure that the WLAN / BT Module STI6290-D101 is installed in a host product intended for indoor use only.
- The antenna(s) must be installed according to the following guidelines.
- Maintain a distance of at least 20 cm between the antenna and users.
- The transmitter module should not be co-located with any other transmitter or antenna.
- For products available in the USA/Canada market, only operate on channels 1~11. Selecting other channels is not possible.
- Ensure that the maximum antenna gain (including cable loss) does not exceed the values specified in the product information table.
- If there are any deviations from the defined parameters of the antenna trace, the host product manufacturer must notify EPSON and follow the necessary procedures for approval.
- Label the host product with the provided FCC ID: BKMAE-STI6290 in a visible area.
- The end product must comply with Part 15 of the FCC Rules and accept any interference received.
- If there are any changes or modifications to the WLAN / BT Module STI6290-D101 that are not approved by the responsible party for compliance, it may void the user’s authority to operate the equipment.
- Follow all other instructions and guidelines provided in the user manual for proper and safe usage of the WLAN / BT Module STI6290-D101.
FCC
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
List of applicable FCC rules
This module has been tested and found to comply with part 15.247, Part 15.407
requirements for Modular Approval. The modular transmitter is only FCC
authorized for the specific rule parts (i.e., FCC transmitter rules) listed on
the grant, and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the
modular transmitter grant of certification. If the grantee markets their
product as being Part 15 Subpart B compliant (when it also contains
unintentional-radiator digital circuity), then the grantee shall provide a
notice stating that the final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.
This device is intended only for OEM integrators under the following
conditions: (For module device use)
- The antenna must be installed such that 20 cm is maintained between the antenna and users, and
- The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Antenna
- The antenna must be installed such that 20 cm is maintained between the antenna and users,
- The transmitter module may not be co-located with any other transmitter or antenna.
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid, and the FCC ID cannot be used on
the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
To comply with FCC regulations limiting both maximum RF output power and human
exposure to RF radiation, maximum antenna gain (including cable loss) must not
exceed.
| Antenna Type | Frequency Band (MHz) | Ant 1 Gain (dBi) | Ant 2 Gain (dBi) |
|---|
Wi-Fi Antenna
PIFA| 2400 ~ 2483.5| 2.34| 2.74
5150 ~ 5250| 3.58| 3.39
5725 ~ 5850| 5.29| 4.50
Bluetooth Antenna
PIFA| 2400 ~ 2483.5| —| 2.74
Important Note
Notice that any deviation(s) from the defined parameters of the antenna trace,
as described by the instructions, require that the host product manufacturer
must notify to EPSON that they wish to change the antenna trace design. In
this case, a Class II permissive change application is required to be filed by
the USI, or the host manufacturer can take responsibility through the change
in FCC ID (new application) procedure followed by a Class II permissive change
application
Label of the end product:
The host product must be labeled in a visible area with the following:
” Contains FCC ID: BKMAE-STI6290 “.
The end product shall bear the following 15.19 statement:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This module is restricted to integration into hosts for indoor use only.
OEM integrator has be limited the operation channels in channel 1-11 for
2.4GHz band.
The separate approval is required for all other operating configurations,
including portable configurations with respect to Part 2.1093 and different
antenna configurations
The information on how to configure test modes for host product evaluation for
different operational conditions for a stand-alone modular transmitter in a
host, , versus with multiple, simultaneously transmitting modules or other
transmitters in a host can be found at KDB Publication 996369 D04
The user manual of the end product should include:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
The antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This device is restricted to indoor use.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
ISED
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The device shall automatically discontinue transmission in cases of absence of
information to transmit, or operational failure.
This device is restricted to indoor use.
- The transmitter module may not be co-located with any other transmitter or antenna.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
OEM integrator is still responsible for testing their end product for any
additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization.
Label of the end product:
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users.
The final end product must be labeled in a visible area with the following:
“Contains transmitter module IC: 1052D-STI6290”. Contient le module d’émission
IC: 1052D-STI6290
The Host Model Number (HMN) must be indicated at any location on the exterior
of the end product or product packaging or product literature which shall be
available with the end product or online.
This device is intended only for OEM integrators under the following
conditions:
- The antenna must be installed such that 20cm is maintained between the antenna and users, and
- The transmitter module may not be co-located with any other transmitter or antenna.
CAN ICES-003(B) / NMB-003(B)
The Country Code Selection feature is disabled for products marketed in the
US/Canada
For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
CE
-
RF power
Compliance with 2014/53/EU Radio Equipment Directive (RED)
In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides information on the frequency bands used and the maximum RF transmit power of the product for sale in the EU:Frequency range (MHz)| Max. Transmit Power (dBm/mW)
---|---
2400-2483.5| 19.57 dBm (90.6mW)
5150-5250| 19.66 dBm (92.5mW)
Bluetooth: 2402-2480| 9.43 dBm (8.77mW) -
RF Exposure Information (MPE)
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. -
The device for operation in the band 5150–5250 MHz is only for indoor use.
| AT| BE| BG| CH| CY| CZ| DE| DK
---|---|---|---|---|---|---|---|---
EE| EL| ES| FI| FR| HR| HU| IE
IS| IT| LI| LT| LU| LV| MT| NL
NO| PL| PT| RO| SE| SI| SK| -
Information of Importer:
EU Importer:
Name：EPSON EUROPE B.V.
Address：Atlas Arena, Asia Building, Hoogoorddreef 5,1101 BA Amsterdam Zuidoost The Netherlands
TEL：31-20-314-5000
FAX：31-20-314-5010
Web：http://www.epson.eu/ -
Information of Manufacturer:
Manufacturer:
Name：SEIKO EPSON CORPORATION
Address：3-3-5, Owa, Suwa-shi, Nagano-ken 392-8502 Japan
T E L：81-263-87-5824 (ex.733-80485) -
Declaration of Conformity
UKCA
-
RF power
Compliance with the Radio Equipment Regulations 2017
In accordance with 13 (2) (a) and 13 (2) (b) of the Radio Equipment Regulations 2017, the following table provides information on the frequency bands used and the maximum RF transmit power of the product for sale in the UK:Frequency range (MHz)| Max. Transmit Power (dBm/mW)
---|---
2400-2483.5| 19.57 dBm (90.6mW)
5150-5250| 19.66 dBm (92.5mW)
Bluetooth: 2402-2480| 9.43 dBm (8.77mW) -
RF Exposure Information (MPE)
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. -
The device for operation in the band 5150–5250 MHz is only for indoor use.
-
Information of Importer:
UK Importer:
Name：Epson (UK) Ltd.
Address：Westside, London Road, Hemel Hempstead, Hertfordshire, HP3 9TD, United Kingdom
TEL：44-1442-261144
FAX：44-1442-227227
Web：http://www.epson.co.uk -
Information of Manufacturer:
Manufacturer:
Name：SEIKO EPSON CORPORATION
Address：3-3-5, Owa, Suwa-shi, Nagano-ken 392-8502 Japan
TEL：81-263-87-5824 (ex.733-80485) -
Declaration of Conformity
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>