GALT02 Gator Range User Guide
- June 13, 2024
- GATOR
Table of Contents
GALT02
QUICK START GUIDE
Please ensure that you have read the product quick start guide and instructions prior to installation and use. Failure to do so may result in the product incorrectly operating or an installation that renders the device unusable.
Product specifications
- Pitch angle: -40° – +40°
- Roll angle: -40° +40°
- Temperature accuracy: ±1°C
- Air pressure: 300-1100hPa
- Voltage measurement range: DC 5-30V
- Voltage measurement accuracy: 0.5 V
- Speed precision: <0.36 Km/h
- GPS start time (Cold): 32s (Average)
- GPS start time (Hot): 1s (Average)
- Data refresh rate of GPS: 1s
- Operating temperature: -40°C+80°C
- Power supply: DC 10V-30V
- Ambient light modes: 24 kinds
Display
- Elevation Altitude
- Pitch
- Roll
- Longitude & Latitude
- Barometer
- Digital Compass
- Speed Meter
- Thermometer
- Voltage Indicator
- Digital Clock / Date
- Fatigue Alarm
- GPS Data Collection
- Volume Adjustment
- Auto Brightness
- Ambient Light
- Speaker
- Ambient Light Mode Setting/ Pitch & Roll Angle Reset
Functions
1. Elevation Altitude| When GPS data is collected, it will display the
elevation altitude.
---|---
2. Pitch| Displays the pitch angle of the car’s current position.
3. Roll| Displays the roll angle of the car’s current position.
4. Longitude & Latitude| Displays the longitude & latitude of the vehicle’s
current location when GPS data is received.
5. Barometer| Displays the atmospheric pressure at the current location of
the vehicle.
6. Digital Compass| When GPS data is collected, it will display the east,
south, west, north, southeast, southwest, northeast, northwest directions
according to the motion track of the vehicle.
7. Speed Meter| When GPS data is collected, it will display the vehicle
speed.
8. Indoor Thermometer| It gets and displays the thermometer through the
temperature sensor in the concentrator.
9. Voltage Indicator| Displays the actual voltage when the display is
connected with the power (in Volts).
10. Electronic Clock| Display the year, month, day, hour of the week. After
GPS data is obtained, it is automatically calibrated according to satellite
timing.
11. Fatigue Alarm| When the vehicle has been working continuously for 4 hours, a fatigue driving icon will be displayed on the display to remind the driver that he needs to rest.
---|---
12. GPS data Collection| When GPS data is collected, it will display GPS icon
to show that GPS data collection is in a normal state.
13. Volume Adjustment| Adjust device volume. Each press will cycle up through
the values (0-9/ 0 is Mute)
14. Auto Brightness| The display will auto adjust the backlight brightness
according to the outside brightness, so to make the display clear, soft and
not dazzling.
15. Ambient Light| An ambient light strip is set under the display, and there
are 0-24 ambient light display modes to choose from, and the ambient light can
also be turned off as needed.
16. Overspeed Alarm| The display will alarm and make a beep, when the car
speed exceeds the threshold, meanwhile the display speed will flash
accordingly.
Installation
- Connect the ACC wire to the ACC power supply of the car, then connect the GND wire to a suitable ground point.
- The plug of GPS module should be plugged into the socket of the concentrator, then position the GPS module in a suitable location on the dashboard in the vehicle to receive optimal signal.
- It is recommended that the display is installed on the centre of the dashboard, close to the windscreen to enable wires to be hidden and ensure a good view for the driver. Install the display using 3M tape after first cleaning the surface.
- After turning on the device for the first time, or after having moved the device, press and hold the reset button (17) whilst the device is powered on for 3-5 seconds to reset/zero the pitch and roll angle to ensure that the values are accurate.
Settings
Volume:
To change the default volume of the device, press the Volume Button(13) whilst
the device is on. Each press will cycle up through the values (0-9/ 0 is Mute)
Time Zone:
To change the default time zone of the device, press and hold the Reset
button(17) whilst the device is off (vehicle ignition is switched off). Then
switch on the vehicle ignition, the current time zone setting will be
displayed on the
Temperature/Voltage display (8)(9).
Note: The default time zone is set to GMT.
Press the Power Button(17) to cycle to the desired value and then turn off the
device. When the device is next powered on, the time zone will be set to the
chosen value.
Measurement:
To measurement readings (speed, altitude, temperature) of
the device can be adjusted from metric to imperial.
Note: The device is set to Metric by default.
| Metric| Imperial
---|---|---
Speed| Km/h| Mph
Altitude| m| ft
Temperature| °C| °F
To change the measurement type, Press and hold the Volume Button(13) whilst
the device is off (vehicle ignition are switched off). Then switch on the
vehicle ignition. The ‘km/h ‘M’ ‘C’ (Metric) or ‘mph’, ‘Ft, ‘F’ (Imperial)
will be displayed on the screen. To cycle between the options, turn off the
ignition and press and hold the Volume Button(13) to display the next option.
Once the desired option has been set, turn on the device, the measurement will
be set to the chosen type.
Ambient Light Mode:
The system provides a total of 24 ambient light modes from 0 to 24 to choose
from. Each time you press the Power Button(17), the mode value is incremented
by 1, and it is adjusted in cycles.
The corresponding relationship between the mode value and the ambient light
mode is as follows:
0: No light
1: Colorful lights
2: Phantom lights
3-9: 7 Kinds of color static light
10-16: 7 Kinds of color breathing light
17-23: 7 Kinds of color running water light
24: Speed light
Over Speed Alarm Setting:
To change speed setting for overspeed alarm, press and hold the Volume
Button(13) while the device is powered on for 3-5 seconds, the current speed
setting will be displayed on the Speed display (5).
Note: The default speed is set to 190Km/h.
Press the Volume Button(13) to cycle to the desired value thenzzz wait for 3-5
seconds, the speed will be set to the chosen value.
Attention
- Due to the affect of the GPS signal, the speed may be delayed, and at the same time, the speed, electronic compass and elevation altitude can’t be displayed normally.
- The GPS signal has a great influence on the elevation altitude, so the lack of GPS signal is a little bigger when it’s obstructed by surroundings (ie buildings, forest).
- The temperature sensor is inside the concentrator, so the indoor temperature is dependent on its position inside the vehicle.
Technical assistance
If you need assistance setting up or using your Gator product now or in the
future, call Gator Support Australia.
TEL: 03 – 8587 8898
FAX: 03 – 8587 8866
Mon-Fri 9am – 5pm AEST
Please retain this user guide for future reference This manual is considered
correct at time of printing but is subject to change. For latest manuals and
updates refer to the website.
http://gatordriverassist.com
For more information on the Gator range go to our website
gatordriverassist.com
Copyright © 2022 by TDJ Australia
www.gatordriverassist.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>