Creative Labs Pte SA0180 Creative BT-W4 User Guide

Creative Labs Pte SA0180 Creative BT-W4

Safety & Regulatory Information

Read this instruction carefully and completely before using the product. Refer to the following information to use your product safely, and to reduce the chance of electric shock, short-circuiting, damage, fire, hearing impairment or other hazards. Improper handling may void the warranty for your product. For more information, read the warranty available with your product.

• Always keep the product dry and do not expose it to extreme temperatures (hairdryer, heater, extended exposure to sunlight, etc.) to avoid corrosion or deformation.
• Do not expose your product to water and moisture. If your product is moisture-resistant, take care and not to immerse in water or expose to rain.
• Clean the product only with a soft, dry cloth.
• Do not dismantle or attempt to repair your product.
• Do not pierce, crush or set fire to your product
• Keep your product away from strong magnetic objects
• Keep the product, accessories and packaging parts out of reach of children and pets to prevent accidents. Swallowing and choking hazard.

Warning on Choking Hazard
This product and its accessories may contain small parts which must be kept away from children.

WARNING
CHOKING HAZARD – Small Parts Not for children under 3yrs.

SAFETY & REGULATORY INFORMATION

The following sections contain notices for various countries.

CAUTION:
This product is intended for use with FCC/CE certified computer equipment. Please check the equipment operating/installation manual and/or with the equipment manufacturer to verify/confirm if your equipment is suitable prior to the installation or use of the product.

Notice for USA

Federal Communication Commission (FCC) Interference Statement
FCC Part 15: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if no installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subjected to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

CAUTION: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules, this device must be installed with computer equipment certified to comply with Class B limits.
All cables used to connect to the computer and peripherals must be shielded and grounded. Operation with non-certified computers or non-shielded cables may result in interference to radio or television reception.

MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device.

Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Creative BT-W4 (SA0180) Additional Safety and Regulatory information

Notice for Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

Canada Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device.

SUPPLIER’S DECLARATION OF CONFORMITY

According to CFR Title 47 §2.1077

Importer’s Name:  Creative Labs, Inc.

Importer’s Address: 1900 McCarthy Boulevard, Suite 103, Milpitas, CA95035 Tel: (408)391-6961

declares under its sole responsibility that the product

Trade Name: Creative
Model Numbers: SA0180
Product Name: Creative BT-W4

has been tested according to the FCC / CISPR22 requirement for Class B devices and found compliant with the following standards:
EMI/EMC: ANSI C63.4 & C63.10, FCC Part 15 Subpart B & C Complies with Canadian ICES-003 Class B & RSS-247 standards

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may causeundesirable operation

Supplementary Information:
Thinh Bui Compliance Manager Creative Labs, Inc. 31 March 2022

European Compliance
This product complies with all applicable directives. A copy of the EU DoC is available at Creative website.

CAUTION: To comply with the Europe CE requirement, this device must be installed with CE certified computer equipment which meet with Class B limits.
All cables used to connect this device must be shielded, grounded and no longer than 3m in length. Operation with non-certified computers or incorrect cables may result in interference to other devices or undesired effects to the product.

MODIFICATION: Any changes or modifications not expressly approved by Creative Technology Limited or one of its affiliated companies could void the user’s warranty and guarantee rights.
The insulating coating on the device also serves the purpose of ESD protection.

Vietnam RoHS Statement
This product is in compliance with Circular 30/2011/TTBCT of the Ministry of Trade of the Socialist Republic of Vietnam (“Circular”), it does not contain the following substances in concentration greater than the Maximum Limit value as specified in the Circular.

Substance Maximum & Limit (ppm)1, 2

• lead 1000
• mercury 1000
• cadmium 100
• hexavalent chromium 1000
• polybrominated biphenyls (PBB ) 1000
• polybrominated diphenyl ethers (PBDE) 1000

1 Maximum Limit does not apply to applications exempted from the Circular.
2 Maximum Limit refers to concentration by weight in homogeneous materials.

Notice for Australia

Notice for Malaysia

Notice for Singapore

Notice for Thailand

This telecommunication equipment conforms to NTC/NBTC technical requirement

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>