SATCO NUVO 64-100 LED Rgbtw Indoor Outdoor Tape Lights Instruction Manual

SATCO NUVO 64-100 LED Rgbtw Indoor Outdoor Tape Lights

Product Information

The LED RGBTW Indoor/Outdoor Tape Lights are versatile lighting fixtures that can be used both indoors and outdoors. There are multiple models available, including 64-100, 64-110, 64-111, 64-120, 64-121, 64-130, 64-131, 64-132, 64-133, 64-134, 64-135, 64-140, 64-141, 64-142, 64-143, 64-144, and 64-145. These lights come with installation and safety instructions that should be carefully followed to ensure proper usage and to prevent any potential risks.

Installation and Safety Instructions

Before installing the fixture, it is important to read and understand the following safety instructions:

• Ensure the fixture is clean and free from grease and dust before installation.
• Do not install the lights on wood, powder-coated, structured surfaces, glass, or stainless steel.
• When cutting the tape lights (applicable to indoor models only), follow the provided guidelines to avoid any risks.
• When installing indoors, gently press the PCB areas of the tape lights while wearing an anti-static ring. Avoid pressing down on the actual LEDs.
• When peeling off the tape for installation, be careful not to overstretch and tear the adhesive tape.
• If unreeling the entire strip before installation, avoid stepping on the reel to prevent damage.
• For outdoor models (64-140, 64-141, 64-142, 64-143, 64-144, and 64-145), use the included brackets for installation as there is no double-sided adhesive included.

WARNING

WARNING: Risk of Fire or Electric Shock

• This tape lighting is only intended to be used with the products provided in the kit.
• Installation requires knowledge of luminaries electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
• To reduce risk of fire and overheating, secure all connections.
• TURN OFF the electrical power before proceeding.
• The electrical rating of this product is 120V/60Hz.
• The grounding and banding of the system shall be done in accordance with National Electric Code (NEC) Article 600 and local codes.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Do not damage any PCB conductive parts, squeeze or fold the LED tape light when installing.
• Pay attention to positive and negative polarities before installation, otherwise the LED tape light may be damaged.
• Prevent static electricity when installing. Avoid damp or wet exposure.
• This device is not intended for use with emergency exits.

CUTTING
Applies to indoor models only 64-100, 64-110, 64-111, 64-120, 64-121, 64-130, 64-131, 64-132, 64-133, 64-134, 64-135.

• Always disconnect the power supply before cutting. LED strips can be cut as indicated in diagram.

INSTALLATION

Indoor Installation
Applies to models 64-100, 64-110, 64-111, 64-120, 64-121, 64-130, 64-131, 64-132, 64-133, 64-134, 64-135.

• STEP 1: Clean surfaces carefully (free from grease and dust) before installing to ensure that the double-sided tape or adhesive sticks properly to the surface. Wood, powder-coated, structured surfaces, glass, stainless steel etc. are not recommended locations.
• STEP 2: Gently peel off the tape, the adhesive tape may tear by over-stretching.
• STEP 3: Wearing an anti-static ring, gently press PCB areas. Do not press down on the actual LEDs.
• STEP 4: Be careful to not step on the reel if you unreel the entire strip before installation.

Outdoor Installation
Applies to models 64-140, 64-141, 64-142, 64-143, 64-144, 64-145. Use included brackets to install the tape. There is no double-sided adhesive with these models.

• STEP 1: Align white arrow on the controller’s cable to (←) symbol on LED strip.

• STEP 2: Connect controller to the power supply or Junction Box.
  NOTE: Actual controller appearance may vary .

• STEP 3A: Plug the power supply into a power outlet.

• STEP 3B: For Junction Box, shut OFF power at the circuit breaker. Connect wires as shown in wiring diagram above. Make sure all wire connectors are secure. After wires are connected, tuck them carefully inside the Junction Box and turn ON power.

Operation

Use the remote control or Starfish APP to control the light strip; such as to turn on and off, brightness and color change.

Manual Control by 3 Buttons & IR Remote Control

USER GUIDE

SYSTEM REQUIREMENTS

• Minimum iOS 9.3 or Wi-Fi 4.4
• Dedicated 2.4GHz Wi-Fi Network

TECHNICAL SUPPORT
support@satcostarfish.com

1. DOWNLOAD THE STARFISH APP
   (App design is subject to change without notice.)
   REGISTER YOUR ACCOUNT
   Verify you’re connected to a 2.4GHz Wi-Fi Network.

2. Launch the STARFISH app and tap “Sign-up” to create a new account or “Login” to your existing account.

3. Enter email address, then select “Get verification code”.

4. Enter the verification code that was sent to your email.
   CREATE A HOME

5. Tap the “Me” button at the bottom of the screen, and then “Home Management”. Select the “Create a home” button to set up your home.
   ADD A DEVICE

6. Tap the(+) button on the top right corner to access the action menu, then select “Add Device”.

7. Select device type from the listed categories.
   PAIR A DEVICE WITH WI-FI

8. To put the device into pairing mode, press and hold the power button for approximately 5 seconds until the tape light starts flashing, then release the button. The device is now ready to be paired.

9. Select your 2.4GHz Wi-Fi Network name and enter password then click “Next.”
   PAIR A DEVICE WITH WI-FI/BLUETOOTH
   Note: Verify your mobile device is connected to a 2.4GHz Wi-Fi Network and that you have Bluetooth turned ON for connection.

   • For Wi-Fi/Bluetooth-enabled devices, you will see a pop-up indicating that there are unpaired devices in the area. The device does not need to be in pairing mode. Tap “Add” and select the devices you would like to connect.
   • Once all the devices have connected, tap “Next”.

10. When successfully connected, you may rename the device. Tap the “Pen” icon, enter the new name and select “Done”. The device is now ready to be controlled with the STARFISH app.
    SHARE A HOME

11. From the Home Management screen, select the Home that you would like to share. Tap “Add Member” and select the way that you would like to send the invitation.

12. Enter the user information and select if the new member will be an “Administrator” or a “Common Member” in the Home. Tap “Save” to send the invitation.

TO VIEW THE ENTIRE STARFISH PRODUCT LINE VISIT Satco.com/STARFISH.

Scan QR Code to learn more:

SPECIFICATION

General

• Status Active
• Fixture Type Tape Light
• Finish White
• Wattage 68W
• Lumen Output 6300L
• IP Rating IP65
• Indoor or Outdoor Fixture Indoor; Outdoor

Smart Product Info

• IOT Enabled Yes
• Voice Assistants Supported Google Home; Alexa; Siri; SmartThings

Specifications

• Technology LED
• Color Temperature RGB and Tunable White
• CRI 80+
• Voltage 24V
• Rated Hours 50000
• Operating Temperature -20C (-4F) to +40C (+104F)
• Dimmable Yes-Dimmable
• Dimming Note Only with Starfish App or Remote Control
• Weight (lb.) 6.6
• Material Plastic

Dimensions

• Width (in.) 0.55
• Length (in.) 787.44

Compliance

• Safety Listing cETLus – Listed
• Location Rating Wet
• Energy Star No
• DLC Approved No
• CA T20 / T24 Rationale T20 Exempt – Fixtures Not Regulated
• California Status Lawful for sale in California
• Title 20 / 24 Status Lawful for sale
• California Prop 65 Lead
• RoHS Compliant Yes
• FCC Compliant Yes
• SDS Sheet LED_Fixture

Additional Information

• Additional Information: Driver Wattage is 80W; Driver Voltage is 120V
• Specification Note: Cuttable: No; Outdoor tape is not recommended to be cut as IP65 rating and warranty become invalidated; High Brightness; Sync to Music
• Installation Notes: 2 reels of 32 feet (10M) to make 64 feet (20M) total; Mounting Clips for outdoor installation
• Includes
  • Kit includes: Outdoor Rated Plugin Driver; Receiver; RF Remote; 80 Mounting Clips; 2-10M Reels
• Warranty 1 Year Limited – Fixtures

SUPPORT CENTER

1 Year Limited – Fixtures
This Satco Products, Inc. product is warranted to be free from defects in materials and workmanship for a period of 1 year from the date of original purchase. The warranty does not cover damage caused by abuse, misuse, improper environmental conditions, wrong installation or shipping damage. If this does not last, return with proof or purchase, and register the receipt with your name & address, For replacement. This replacement is the sole remedy available and liability for incidental or consequential damages is hereby expressly excluded. This warranty shall not apply to any product that is found to have been improperly installed, set up, or used in any way not in accordance with the instructions supplied with the product. Satco does not warrant and specially disclaims any warranty, whether expressed or implied, of fitness for a particular purpose, other than the warranty contained herein. Satco specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including any labor/expense costs involved in the replacement or repair of said product.

Copyright 2020 Satco Products, Inc.
All Rights Reserved For More Information Visit: http://www.satco.com/

References

• SATCO/NUVO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>