EUROM Sani Wi-Fi Wall Heat 2000 User Manual

EUROM Sani Wi-Fi Wall Heat 2000

Product Information

• Model: Sani Wi-Fi
• Product Code: 350067 (Sani 400 Wi-Fi White)

Available Models:

• Sani 400 Wi-Fi White
• Sani 400 Wi-Fi White (Swiss plug)
• Sani 400 Wi-Fi Black
• Sani 400 Wi-Fi Black (Swiss plug)
• Sani 600 Wi-Fi White
• Sani 600 Wi-Fi White (Swiss plug)
• Sani 600 Wi-Fi Black
• Sani 600 Wi-Fi Black (Swiss plug)
• Sani 800 Wi-Fi White
• Sani 800 Wi-Fi White (Swiss plug)
• Sani 800 Wi-Fi Black
• Sani 800 Wi-Fi Black (Swiss plug)
• Sani 1000 Wi-Fi White
• Sani 1000 Wi-Fi White (Swiss plug)
• Sani 1000 Wi-Fi Black

Product Usage Instructions

Please read and understand the following instructions before using the Sani Wi-Fi:

Warnings:

• Do not cover the heater to prevent overheating.
• Keep the heater away from babies and children to avoid suffocation hazards.
• Some parts of the product can become very hot and cause burns. Be cautious when children or vulnerable persons are near the device.
• This device is not suitable for individuals with physical, sensory, or mental impairments or lack of experience and knowledge (including children). Keep the device out of reach of children, unauthorized individuals, and pets. Never leave the device unattended when it is turned on.
• The device becomes very hot. Do not touch the device during use or within five minutes after use.
• Use the towel brackets only for drying towels. Do not cover the device during use or after use if the device is still hot. Keep textiles (except towels), curtains, tent fabrics, and other flammable materials at a minimum distance of 1 meter from the device to reduce the risk of fire.
• If the device, power cord, or plug is damaged or malfunctioning, immediately discontinue use and disconnect the power supply.

Warranty:
EUROM provides a 60-month warranty for this device from the date of purchase. Wear and tear due to normal use are not covered by the warranty. The warranty will be void if a defect is a result of accidental or careless use of the device. The manufacturer, importer, and supplier are not liable for incorrect connections.

Introduction:
Please read this user manual thoroughly and ensure that you understand everything before assembling, installing, and using the device.

This manual describes the correct and safe use of this device.
Keep this manual for future reference. The manual is an essential part of the device and must be handed over to the new owner when reselling or exchanging. This manual has been compiled with the utmost care. However, we reserve the right to improve and modify this manual at any time. The images used may vary.

The following symbols and terms are used in this manual to alert the reader to safety issues and important information:

Mandatory warnings

Please read and understand these safety instructions. Incorrect use can cause injury and will void EUROM’s warranty.

WARNING
In order to avoid overheating, do not cover the heater.

• The heater must not be used if the glass panels are damaged.
• This appliance is intended only for drying textiles washed in water.
• Plastic bags can be dangerous. To avoid danger of suffocation, keep this bag away from babies and children.

CAUTION

• Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
• In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
• Children of less than 3 years should be kept away unless continuously supervised.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Heater must not be located immediately below a socket-outlet.
• If the supply cord is damaged, it must be replaced by manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Heater is to be installed so that switches and other controls cannot be touched by a person in the bath or shower.

This device is not suitable for use by persons with a physical, sensory or mental disability, or lack of experience and knowledge (including children). Keep the device out of reach of children, unqualified persons and pets. Never leave the device unattended while it is in operation.

The device is equipped with an overheating protection, which switches it off automatically in case of internal overheating. Switch the device off, unplug the power plug, remove the source of overheating, let it cool down and use as normal. Do not use the device if the source of overheating cannot be traced or if the problem persists, but always contact your supplier.

This device is save to use in the bathroom when the device is mounted:

• in zone 3 of a toilet room or bathroom with a bath, shower with screen and shower without screen (Figure 1);
• in a fixed position;
• out of reach for operation by a person in a bath or shower.

General safety instructions

WARNING

• Prevent splashing water on or in the device.
• Do not immerse any part of the device in water or other liquids.
• Never insert fingers or other objects into the openings of the device.
• Do not expose the device to strong vibrations or mechanical stress.

WARNING
The device becomes very hot during use. Do not touch the device during use or within five minutes after use.

CAUTION
Only use the towel rails to dry towels. Do not cover the device otherwise, during usage or after use while the device is still hot. To reduce the risk of fire, keep textiles (other then towels), curtains, tent canvasses and other flammable material at a minimum distance of 1 meter from the device.

Safety during operation

WARNING
Do not use the device:

• outdoors or in a small space (< 7 m3);
• lying, leaning or standing;
• if any parts are dirty or wet;
• near large objects, like behind a door, under a shelf or cupboard;
• near a water source, like a bath, shower, swimming pool or open window;
• near or in a dusty and dirty environment, like a construction site;
• near flammable materials, liquids or fumes, like a shed, stable or green house;
• near other heat sources and open fire;
• near, under or facing a socket outlet;
• with an appliance that automatically switches the device on, such as a timer, dimmer or any other device.

If the device, the electric cable or plug shows damage or is malfunctioning, immediately take the appliance out of use and disconnect the power supply.

Warranty
EUROM offers a 60-month warranty on this device from the date of purchase. The warranty does not cover wear and tear from normal use. The warranty expires if a defect is the result of unintentional or careless use of the device. The manufacturer, importer and supplier are not liable for incorrect connections.

Introduction

Thank you for choosing this EUROM device. You have purchased a quality device that you will enjoy for many years. Using this device with respect and care will reduce the risk of personal injury or material damage.

CAUTION
It is important to read and understand this instruction manual before assembling, installing and using the device.

This manual describes the correct and safe use of this device. Keep this manual for future reference. The manual is an essential part of the device and must be given to the new owner upon resale or exchange. This manual has been compiled with the utmost care. Nevertheless, we reserve the right to improve and adjust this manual at any time. The images used may differ.

The following symbols and terms are used in this manual to alert the reader on safety issues and important information:

WARNING
Indicates a hazardous situation which, if the safety instructions are not followed, can lead to injuries to the operator or bystanders, light and/or moderate damage to the product or to the environment.

CAUTION
Indicates a hazardous situation which, if the safety instructions are not followed, can lead to light and/or moderate damage to the product or to the environment.

Identification

Specifications

127 cm
Weight:| 6.74 kg| 9.0 kg| 10.52 kg| 11.50 kg
Voltage:| 220-240V~50Hz| 220-240V~50Hz| 220-240V~50Hz| 220-240V~50Hz
Power:| 400W| 600W| 800W| 1000W
Protection rating:| IP24| IP24| IP24| IP24
Protective class:| Class I| Class I| Class I| Class I

Hereby, Euromac b.v. declares this product is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.eurom.nl/declaration-of- conformity.

• Wi-Fi and Bluetooth Frequency Band: 2,400 ~ 2,483.5GHz
• Maximum radio-frequency power transmitted in this frequency band(s):
  • Wi-Fi: 17,5dBm
  • Bluetooth: 6,5dBm

Description

The Sani Wi-Fi (Figure 4) is an easy-to-use electric bathroom heater for use in zone 3 of the bathroom (Figure 6). The Sani Wi-Fi can be used with the Eurom Smart App.

1. Main device
2. Towel rail
3. ON/OFF switch
4. Control panel and LED display
5. Power plug

Control panel and display

1. Wi-Fi indication
2. Timer button
3. Square bracket
4. Minus button
5. Plus button
6. Temperature indication

The LED-screen will extinguish automatically after ± 15 seconds, the square brackets remain visible. Touch the device between the square brackets (Figure 5, pos. 3) to light it up again.

Transport and storage

• Clean the device before storing it.
• Transport the device upright.
• Store the device upright in its original packaging in a cool, dry and dust-free area.

Assembly
The device is packed in one box. Remove all packaging material and check that the device is not damaged. Do not use the device if it is damaged, but always contact your supplier. Keep the packaging for safe storage and transport.

Wall mounting

WARNING
The wall used for mounting must be made from non-flammable material and should be able to withstand a minimum temperature of 125 °C.

CAUTION
Make sure to use suitable fastening materials, depending on the surface. Never block the space between the device and the wall.

1. Place the device on a non-flammable and solid wall.

2. Place the device with a minimum distance (Figure 6) of:

   • 50 cm from the ceiling;
   • 20 cm from the side walls;
   • 10 cm from the floor;
   • 50 cm clearance on the front side.

3. Do not mount the device:

   • immediately below a socket outlet;
   • on a ceiling or roof.

4. Place the wall bracket against the wall and mark the five holes (Figure 7).

5. Drill five holes at the marked spots.

6. Place the plugs (Figure 7, pos. 3).

7. Screw and tighten the wall bracket (Figure 7, pos. 1) to the wall with five large screws (Figure 7, pos. 2) using a Phillips screwdriver (Figure 7, pos.4).

8. Lay the device down on a soft steady surface (Figure 8, pos. 4).

9. Place the two towel rails (Figure 8, pos. 3) on two of the three possible locations on the main body (Figure 8, pos. 5).

10. Screw and tighten the two towel rails
    (Figure 8, pos. 3) with eight small screws
    (Figure 8, pos. 2) using a Phillips screwdriver (Figure 8, pos. 1).

11. Place the device brackets (Figure 9, pos. 3) over the wall bracket (Figure 9, pos. 1).

12. Slide the device (Figure 9, pos. 2) into the openings of the wall bracket.

13. Screw and tighten the device
    (Figure 10, pos. 1) with a small screw
    (Figure 10, pos. 3) to the wall bracket using a Phillips screwdriver (Figure 10, pos. 2).

Installation

WARNING
Do not put the power plug into the wall socket before the device is correctly mounted.
Do not use an extension cable; this can cause overheating and fire. If using an extension cable is unavoidable, make sure it is undamaged and earthed. Use an extension cable with a minimum power of 800 Watt. Always unwind the extension cable completely to prevent overheating.

CAUTION
Make sure that the main voltage is the same as indicated on the identification label of the device. All electrical connections must stay dry under all circumstances.

1. Make sure the device is correctly mounted.
2. Make sure the ON/OFF switch is in the OFF position (Figure 11, pos. 2).
3. Place the power plug (Figure 11, pos. 1) into an earthed wall socket that is easily accessible. Use an earthed wall socket with a minimum power of 800 Watt.

Operation

WARNING
Before every use, make sure that:

• you operate the device with dry hands;
• the device is clean and dry;
• the device is not damaged;
• the device is not covered or blocked;
• the device is securely mounted.

CAUTION
When the device is turned on or off, it may emit a sound. This is material expanding and shrinking during heating and cool-down.

1. Set the ON/OFF switch to the ON position (Figure 12, pos. 1).
2. The control panel and display (Figure 12, pos. 2) will light up.
3. Press the Plus or Minus button to set the desired temperature, from 0 °C to 37 °C. The device starts heating when the set temperature is higher then the ambient temperature.
4. The display will first show the set temperature for 3 seconds followed by the ambient temperature.

Set the countdown timer

1. Press the Timer button once or multiple times to set the countdown timer, from 00 to 24 in whole hours.

Once the countdown is over, the device turns off. The device is turned on again when you press the plus button for 3 seconds. The main switch then does not need to be turned on.

Eurom Smart App
The device can be operated using an app on a smartphone or tablet. The Eurom Smart app can be used to:

• switch the device on and off (without anticipation);
• regulate the temperature;
• set daily timer settings on and off, on the weekly timer.
  1. Open the Eurom Smart App manual with the QR code (Figure 13) or go to www.eurom.nl/nl/manuals.
  2. Complete the Eurom Smart App manual.
• When the device is connected with Wi-Fi, the Wi-Fi symbol appears on the screen.
• If the Wi-Fi symbol is blinking there is no connection.

Smart Timer

1. Create a schedule with days and times in the Eurom Smart app. Timer settings set in the app:
   • will be stored on the device;
   • will not be visible on the device;
   • will remain available if Wi-Fi disconnects;
   • will remain available if the device is switched off or unplugged;
   • can only be removed via the app.
2. Check the data in the app regularly.

Reset Wi-Fi connection

1. Press and hold the Timer button until the Wi-Fi symbol starts blinking alternating fast and slow. Existing connections will be deleted and a new connection can be made.

Switch off Wi-Fi connection

1. Press and hold the Minus button until a short beep sounds. The Wi-Fi is switched off and the Wi-Fi symbol will disappear from the screen.
2. Press and hold the Minus button until a short beep sounds. The Wi-Fi is switched on and the Wi-Fi symbol will appear on the screen.

After operation

CAUTION
Do not use the power cable to unplug or carry the device. Do not wind the power cable too tightly or in sharp corners. Do not wrap the power cable around the device.

1. Make sure the ON/OFF switch is in the OFF position (Figure 11, pos. 2).
2. Disconnect the power plug from the power outlet (Figure 11).
3. Let the device cool down before touching it.
4. Wind the power cable.

Maintenance

WARNING
Do not perform any repairs or modifications to this device.
Maintenance and repairs must be carried out by a EUROM authorized professional. If the electric cable and/or electric plug is damaged, it should be replaced by the manufacturer or its service employee or persons with similar qualifications to prevent risks.

Cleaning

WARNING
The device becomes very hot. Make sure the device is turned off, unplugged and completely cooled down.

CAUTION
Do not use:

• scouring pads;
• hard brushes;
• flammable, aggressive or chemical cleaning products.

Prevent water from entering the device. Do not immerse any part of the device in water or other liquids.

It is recommended to clean the device after each use and prior to storage.

1. Wipe the device with a damp, clean, soft, lint-free cloth or a soft brush.
2. Let the device dry completely prior to use and storage.

Disposal
Correct Disposal of this product.
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

Information requirment for the electric local space heaters

Model identifier(s): Sani 400 Wi-Fi
Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric storage local

space heaters only (select one)

Nominal heat output| Pnom| 0,4| kW| manual heat charge control,

with integrated thermostat

| No
Minimum heat output (indicative)| Pmin| 0,0| kW| manual heat charge control with room and/or outdoor

temperature feedback

| No
Maximum continuous heat

output

| Pmax,c| 0,4| kW| electronic heat charge control with room and/or outdoor

temperature feedback

| No
Auxiliary electricity consumption| fan assisted heat output| No
At nominal heat

output

| elmax| 0,4| kW| Type of heat output/room temperature

control (select one)

At minimum heat

output

| elmin| 0,0| kW| single stage heat output and no

room temperature control

| No
In standby mode| elSB| 0,001| kW| Two or more manual stages, no

room temperature control

| No
| | | | with mechanic thermostat room

temperature control

| No
| | | | with electronic room

temperature control

| No
| | | | electronic room temperature

control plus day timer

| No
| | | | electronic room temperature

control plus week timer

| Yes
| | | | Other control options (multiple selections

possible)

| | | | room temperature control, with

presence detection

| No
| | | | room temperature control, with

open window detection

| No
| | | | with distance control option| Yes
| | | | with adaptive start control| No
| | | | with working time limitation| No
| | | | with black bulb sensor| No
Contact details| Eurom – Kokosstraat 20 – 8281 JC – Genemuiden – The Netherlands
Information requirment for the electric local space heaters

Model identifier(s): Sani 600 Wi-Fi
Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric storage

local space heaters only (select one)

Nominal heat output| Pnom| 0,6| kW| manual heat charge control,

with integrated thermostat

| No
Minimum heat output (indicative)| Pmin| 0,0| kW| manual heat charge control with room and/or outdoor

temperature feedback

| No
Maximum continuous heat

output

| Pmax,c| 0,6| kW| electronic heat charge control with room and/or outdoor

temperature feedback

| No
Auxiliary electricity consumption| fan assisted heat output| No
At nominal heat

output

| elmax| 0,6| kW| Type of heat output/room temperature

control (select one)

At minimum heat

output

| elmin| 0,0| kW| single stage heat output and no

room temperature control

| No
In standby mode| elSB| 0,001| kW| Two or more manual stages, no

room temperature control

| No
| | | | with mechanic thermostat room

temperature control

| No
| | | | with electronic room

temperature control

| No
| | | | electronic room temperature

control plus day timer

| No
| | | | electronic room temperature

control plus week timer

| Yes
| | | | Other control options (multiple selections

possible)

| | | | room temperature control, with

presence detection

| No
| | | | room temperature control, with

open window detection

| No
| | | | with distance control option| Yes
| | | | with adaptive start control| No
| | | | with working time limitation| No
| | | | with black bulb sensor| No
Contact details| Eurom – Kokosstraat 20 – 8281 JC – Genemuiden – The Netherlands
Information requirment for the electric local space heaters

Model identifier(s): Sani 800 Wi-Fi
Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric storage

local space heaters only (select one)

Nominal heat output| Pnom| 0,8| kW| manual heat charge control,

with integrated thermostat

| No
Minimum heat output (indicative)| Pmin| 0,0| kW| manual heat charge control with room and/or outdoor

temperature feedback

| No
Maximum continuous heat

output

| Pmax,c| 0,8| kW| electronic heat charge control with room and/or outdoor

temperature feedback

| No
Auxiliary electricity consumption| fan assisted heat output| No
At nominal heat

output

| elmax| 0,8| kW| Type of heat output/room temperature

control (select one)

At minimum heat

output

| elmin| 0,0| kW| single stage heat output and no

room temperature control

| No
In standby mode| elSB| 0,001| kW| Two or more manual stages, no

room temperature control

| No
| | | | with mechanic thermostat room

temperature control

| No
| | | | with electronic room

temperature control

| No
| | | | electronic room temperature

control plus day timer

| No
| | | | electronic room temperature

control plus week timer

| Yes
| | | | Other control options (multiple selections

possible)

| | | | room temperature control, with

presence detection

| No
| | | | room temperature control, with

open window detection

| No
| | | | with distance control option| Yes
| | | | with adaptive start control| No
| | | | with working time limitation| No
| | | | with black bulb sensor| No
Contact details| Eurom – Kokosstraat 20 – 8281 JC – Genemuiden – The Netherlands
Information requirment for the electric local space heaters

Model identifier(s): Sani 1000 Wi-Fi
Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric storage

local space heaters only (select one)

Nominal heat output| Pnom| 1,0| kW| manual heat charge control,

with integrated thermostat

| No
Minimum heat output (indicative)| Pmin| 0,0| kW| manual heat charge control with room and/or outdoor

temperature feedback

| No
Maximum continuous heat

output

| Pmax,c| 1,0| kW| electronic heat charge control with room and/or outdoor

temperature feedback

| No
Auxiliary electricity consumption| fan assisted heat output| No
At nominal heat

output

| elmax| 1,0| kW| Type of heat output/room temperature

control (select one)

At minimum heat

output

| elmin| 0,0| kW| single stage heat output and no

room temperature control

| No
In standby mode| elSB| 0,001| kW| Two or more manual stages, no

room temperature control

| No
| | | | with mechanic thermostat room

temperature control

| No
| | | | with electronic room

temperature control

| No
| | | | electronic room temperature

control plus day timer

| No
| | | | electronic room temperature

control plus week timer

| Yes
| | | | Other control options (multiple selections

possible)

| | | | room temperature control, with

presence detection

| No
| | | | room temperature control, with

open window detection

| No
| | | | with distance control option| Yes
| | | | with adaptive start control| No
| | | | with working time limitation| No
| | | | with black bulb sensor| No
Contact details| Eurom – Kokosstraat 20 – 8281 JC – Genemuiden – The Netherlands

Kokosstraat 20, 8281 JC Genemuiden, The Netherlands
T: (+31) 038 385 43 21
E: info@eurom.nl
I : www.eurom.nl
Model: Sani Wi-Fi Date: 21/07/2023
Version: v5.0

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>