GE PK-00105060-3 Color Changing RGBW 18W LED 20ft Plug In Tape Light Kit Installation Guide

GE PK-00105060-3 Color Changing RGBW 18W LED 20ft Plug In Tape Light Kit

Installation Guide

PRODUCT COVERED

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING

• Risk of fire or electric shock. Installation requires knowledge of luminaire electricalsystems. If not qualified, do not attempt installation. Contact a qualified electrician.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metalor other sharp objects.
•  This device is not intended for use with emergency exits.
•  These products are intended to be used in dry or damp locations.
•  The luminaire is NON-dimmable.

PREPARE ELECTRICAL WIRING

Electrical Requirements

The LED fixture must be supplied with 120VAC 60Hz.

Grounding Instructions

The grounding and bonding of the overall system shall be done in accordance with National Electric Code (NEC) Article 600 and local codes.

TOOLS REQUIRED

Note: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference; (2) this device must accept
any interference received, including interference that may cause undesired operation.

PACKAGE CONTENTS

INSTALLATION

Before installation, select a location where you want to install, measure the required length of tape light, and mark it. Confirm that the adapter power cord will reach the desired power outlet and when connected to LED tape light. Clean the mounting surface and keep it dry. It is important that the surface is smooth and clean for proper adhesion.
DO NOT POWER ON THE ADAPTER UNTIL INSTALLATION IS COMPLETE.

Turn off power source to the power supply where you are installing the fixture.

Adjust tape light length. It should only be cut in the designated locations. The distance between these marks is 16.7cm.

If cut too short, use the connector to link two tape light segments. Following steps 3a to 3c, align the same polarity symbols and press connector tightly to ensure a good electrical connection.

Flexible connecting cord can be used in corners where the light strip is unable to bend. Following steps 4a to 4c, align the same polarity symbols and press connector tightly to ensure a good electrical connection.

Connect the tape light to another one (if more tape light contained in package), ensure that the polarity symbols are aligned.

Remove the paper liner from the back of the tape light and press against the mounting surface. Ensure minimal hand contact to the adhesive. (For suitable
surfaces, provided clips & screws can be used to secure the tape in place) Do not reposition tape light once it is mounted. once in place, allow the tape adhesive to cure for 24h before use.

If there is a LED chip in a corner when placing the tape light, ensure the angle of the bend is greater than 90 degrees to ovoid damaging the LED chip. See illustration above.

Connect the tope light to IR controller, ensure that the polarity symbols are aligned. Ensure IR receiver location is visible to receive signals from remote controller. Stick the IR receiver to o dry and cleon location using the 3M tape. Connect power adopter to IR controller and plug the adapter into the outlet.

REMOTE CONTROLLER

Pull the plastic card out from the battery compartment. See below for the functions of each button:

CHANGING THE BATTERY

Push tab and open, illustrated above, to change the CR2025 battery.

WARNING

Chemical Burn Hazard- Do not ingest or swallow coin cell battery. This remote control contains a com cell battery. If the coin cell battery 15 swallowed or ingested, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used coin cell batteries away
from children. If the battery compartment does not close securely, stop using the remote control and keep away from children. If you think coin cell batteries have been swallowed or placed inside any part of the body, seek immediate medical attention

CONTROLLER

Controller Button- Short press the button to turn ON the strip light. Short press again to start the smooth mode. To stop at a desired color, short press the controller button
again. Long press the button (3 seconds) to turn OFF. The strip has a memory function and will turn ON at the last color setting.

The sensor can receive remote signals up to 16ft away within 60 degrees.
Ensure the receiver is oriented the correct direction, as shown above.

GE Lighting, a Savant company – 1-800-435-4448 – www.gelighting.com
GE IS A TRADEMARK OF GENERAL ELECTRIC COMPANY. USED UNDER TRADEMARK LICENSE. ©2021 GE LIGHTING, A SAVANT COMPANY INFORMATION PROVIDED IS SUBJECT TO CHANGE WITHOUT NOTICE. ALL VALUES ARE DESIGN OR TYPICAL VALUES WHEN MEASURED UNDER LABORATORY CONDITIONS.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>