GE PK-00106242-3 Color Changing 18 In Gun Metal Modern Contemporary LED Flush Mount Light Installation Guide
- June 13, 2024
- GE
Table of Contents
**Installation Guide
**
PRODUCT COVERED
Model| Input voltage
(Vac, H2)| Current
(mA)| Wattage
w)
---|---|---|---
FLM18DW240D95CGMNG2| 120, 60| 300| 33
DIMMING
The luminaire is dimmable with most regular dimmers.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING
- Risk of fire or electric shock. LED ceiling light installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Risk of fire or electric shock. Install this luminaire only in junction box that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating does not exceed the input rating of the luminaire.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- This device is not intended for use with emergency exits.
These products are intended to be used in dry or damp locations.
Min 90°C (194°F) supply conductors suitable for operation in an ambient not
exceeding 40°C (104°F).
This device complies with Part 15 of the FCC Rules. Operations is subject to
the following two conditions: (1) This device may not cause harmful
interference. And (2) this device must accept any interference received,
including interference that may cause undesired operation. This device
complies with CAN ICES-005 B.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
reorient or relocate the receiving antenng, increase the separation between
the equipment and receiver, connect the equipment into an outlet on a circuit
different from that to which the receiver is connected, or consult the dealer
or an experienced radio/TV technician for help.
PREPARE ELECTRICAL WIRING
Electrical Requirements
The LED fixture must be supplied with 120VAC 60Hz.
Grounding Instructions
The grounding and bonding of the overall system shall be done in accordance
with National Electric Code (NEC) Article 600 and local codes.
PACKAGE CONTENTS
TOOL REQUIRED
Risk of Damage: Must use UL approved conduit fittings for all enclosure box connections to prevent wire cuts by sharp edges and excessive strain on wiring.
INSTALLATION
This fixture is designed to be mounted to a junction box with a screw hole spacing of 2.75″ (70mm) or 3.50″ (90mm).
Turn off power source. Take out the lamp shade and base plate from package. Install 2 screws into the screw holes in the junction box. Connect black, white and green wire from the fixture to black/live, white/neutral and green/ground wire from the outlet box correspondingly. Secure wires together with wire nuts. If no ground wire is present, consult a qualified electrician. Align key slot holes on fixture with fixture screws, push up and twist. Screw fixture to ceiling. Move the switch to select your desired color temperature. Align the four tabs on the fixture plate with the slots on shade. Twist shade clockwise until it stops. Restore power.
PK-00106242-3
GE Lighting, a Savant company
+ 1-800-435-4448
-« www.gelighting.com
GE and C by GE are trademarks of General Electric Company. Used under
trademark license.
INFORMATION PROVIDED IS SUBJECT TO CHANGE WITHOUT NOTICE. ALL VALUES ARE
DESIGN OR TYPICAL VALUES WHEN MEASURED UNDER LABORATORY CONDITIONS.
©2020 GE LIGHTING, A SAVANT COMPANY.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>