GE 93129122_PK-00105061-2 Color Changing RGBW 3W LED Television Tape Light Strip Kit Installation Guide
- June 13, 2024
- GE
Table of Contents
GE 93129122_PK-00105061-2 Color Changing RGBW 3W LED Television Tape
Light Strip Kit
PRODUCT COVERED:
BEFORE VDU BEGIN
Read these instructions completely and carefully.
WARNING
- Risk of fire or electric shock. Installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt instollation. Contoct a quolified electrician.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- This device is not intended for use with emergency exits.
- These products are intended to be used in dry or damp locations.
- The lumin□ire is NON-dimmable.
Prepare Electrical Wiring
Electrical Requirements
The LED fixture must be supplied with 5V/1A.
Grounding Instructions
The grounding and bonding of the overall system shall be done in accordance
with National Electric Code(NEC) Article 600 and local codes.
PACKAGE CONTENTS
TAP084UB0230R8RWBKRMC
Note: This device complies with port 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; 2) this device must accept any interference received, including interference that may cause undesired operation.
INSTALLATION
Tape Light installation
Before installation, select a location where you want to install, measure the
required length of tape light, and note it. Confirm that the Tape Light
reaches the nearest USB outlet. Clean the mounting surface and keep it dry. DD
NOT PLUG USB CORD TD POWER SOURCE UNTIL INSTAUATIDN IS COMPLETE.
Turn off power source to the TV in which you are installing the USB Tape Light.
Adjust tape light length with the cord clips to meet screen size.
Attach tape light to the TV surface. The tape light fits TV sizes ranging from 30″ to 65″. Tape light patterns con vary based on screen size.
Plug the USB connector to a TV, computer laptop, or USB adapter.
REMOTE CONTROLLER
Pull the plastic card out from the battery compartment. See below for the functions of each button:
- On/off button, turn on or turn off the tape light
- Timer button, use it to automatically turn off the lights after a pre-selected time . Press once for 1 hour, twice for 2 hours, and so on for a maximum of 8 hours
- Strobe/Flash button, use it to switch to strobe and flash modes
- Smooth/Fade button, use it to switch to smooth and fade modes
- White light output. use it to switch to white light mode
- Dim down button, use it to decrease the brightness
- Dim up button, use it to increase the brightness
- CD Colour buttons, use these to select different colours.
CHANGING THE BATTERY
Push tab and open, as illustrated, to change the CR2025 battery.
WARNING: CHEMICAL BURN HAZARD – DD NOT INGEST DR SWALLOW COIN CELL
BATTERY. THIS REMOTE CONTROL CONTAINS A COIN CELL BATTERY. IF THE COIN CELL
BATTERY IS SWALLOWED DR INGESTED, IT CAN CAUSE SEVERE INTERNAL BURNS IN JUST 2
HOURS AND CAN LEAD TD DEATH. KEEP NEW AND USED COIN CELL BATTERIES AWAY FROM
CHILDREN. IF THE BATTERY COMPARTMENT DOES NOT CLOSE SECURELY, STOP USING THE
REMOTE CONTROL AND KEEP AWAY FROM CHILDREN. IF YOU THINK COIN CELL BATTERIES
HAVE BEEN SWALLOWED OR PLACED INSIDE ANY PART OF THE BODY, SEEK IMMEDIATE
MEDICAL ATTENTION.
The sensor can receive remote sign□ls up to 16ft away within 60 degrees.
Ensure the receiver is oriented the correct direction, as shown above.
GE Lighting, a Savant Company
1-800-435-4448
www.gelighting.com
GE Is o trademark of General Electric Company. Used under trmtemork license.
INFORMATION PROVIDED IS SUBJECT TO CHANGE WITHOUT NOTICE. ALL VALUES ARE
DESIGN OR TYPICAL VALUES WHEN MEASURED UNDER LABORATORY CONDITIONS.
©2021 GE Lighting, a Savant Company.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>