EDIFIER TWS200 V5.3 TWS Wireless Earbuds User Manual
- June 13, 2024
- Edifier
Table of Contents
EDIFIER TWS200 V5.3 TWS Wireless Earbuds User Manual
Product display
Headphone configuration parameters
Model: TWS200
Version: V5.3
Function operation
-
Starting up : Open the charging bin top cover to start up automatically with indicator light flashes
-
Shut down : Automatically shuts down when charging and indicator light remains on for 2 seconds before turning off
-
The red light flashes once every 5 seconds when low battery
-
Charging for earphones: The red light is always on when charging and it’ll turn onff when full charged. Charging bin:The light is always on when charging the earphones and it’ll turn off when full charged.The light flashes when charging the charging bin and it’ll turn off when full charged.
-
Bluetooth pairing: The earphones will connect to each other automatically when turn on.The main earphone’s light flashes red and blue alternately when connecting successfully while the auxiliary earphone’s light turn off.
-
Volume up: Triple click the right earphone
Volume down： Triple click the left earphone -
Previous song: Double click the left earphone
-
Next song: Double click the right earphone
-
Pause : Click the left earphone
EDIFIER TWS200 V5.3 TWS Wireless Earbuds User Manual
| BT version | V5.3 |
|---|---|
| Transmission distance | 10M |
| BT Protocol | a2dp\avctp\avdtp\avrcp\hfp\spp\smp\att\gap |
| Frequency | 2.402GHz~2.480GHz |
| Signal to Noise Ratio | 101dB |
| Working time | 4H |
| Charging time | 1H |
| Earphone battery | 30mAh |
| Charging bin battery | 180mAh |
| Standby time | 2000H when power off,60H when connected to mobilephone |
| Distortion | 80dB |
| Voltage | 5V |
| Current | Earphone: 30mA Charging bin: 200mA |
| Input power | Earphone: 0.15W Charging bin: 1W |
| Standby current | Earphone: <500uA Charging bin: 19uA |
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, theuser is encouraged to
try to correct the interference by one or more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. -
Consult the dealer or an experienced radio/TV technician for help.
-
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Warranty card
Dear user, this warranty card is your voucher for applying for warranty in the future. Please cooperate the seller shall fill in and keep it properly for future use!
| User info | User name |
|---|
Contact address
Contact number
Product information| Product name
Product model
Barcode/number
Remarks|
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>