genie HDMC221V2 2.1MP HD SDI Encapsulated Camera With 3.6mm Fixed Lens User Manual

: June 13, 2024
: GENIE

Table of Contents

genie HDMC221V2 2.1MP HD SDI Encapsulated Camera With 3.6mm Fixed Lens
Product Information
Product Usage Instructions
Introduction
Specification
Connection
OSD Manual
Hidden Menu
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

genie HDMC221V2 2.1MP HD SDI Encapsulated Camera With 3.6mm Fixed Lens

Product Information

The Genie HDMC221V2 is a 2.1MP HD-SDI encapsulated camera with a 3.6mm fixed lens. It features an electronic shutter with digital slow shutter (DSS) and has a minimum illumination level. The camera also has functions like white balance adjustment, D-WDR, auto gain control (AGC), day and night mode, noise reduction, motion detection, privacy mask, image rotation, defog, and sharpness control. It supports OSD control and multiple languages. The camera provides video output and is powered by a power supply. It has a compact and lightweight design.

Product Usage Instructions

Installation
Connect the camera to a monitor using the appropriate cables.
If using RS-485 communication, choose the appropriate type.
OSD Manual
Refer to the function description in the manual for OSD control.
Hidden Menu
To convert SDI output mode:

  * Enter RS485 mode by pressing the [LEFT] [LEFT] [RIGHT] [RIGHT] key.
  * Press the UP/DOWN/LEFT/RIGHT key 3 times for AD-KEY.
  * Select the desired mode by pressing the UP/DOWN/LEFT/RIGHT key:
    * EX-SDI 2.1 (press UP key 5 times)
    * EX-SDI 2.0 (press DOWN key 5 times)
    * HD-SDI (press LEFT key 5 times)
    * EX-SDI 1.0 (press RIGHT key 5 times)
  * Confirm the selection within 30 seconds by checking the ‘YES’ option. Otherwise, the value will return to the previous setting.

RS-485
Refer to the communication specification for RS-485.
For OSD remote control, use PELCO-D or PELCO-P protocol.

Intro Section

Please read this instruction carefully before operating the product and keep it for further reference. All examples and pictures used here are for reference only. The contents of this manual are subject to change without notice.

CAUTION:

Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, orother apparatus (including amplifiers) that produce heat.
To help prevent electric shock, plug the equipment and peripheral power cables into properly polarized or grounded electrical outlets. These cables are equipped with the wide blade or the third prong to ensure proper grounding.
Do not use adapter plugs or remove the grounding prong from a cable. If the provided plug does not fit your outlet, consult an electrician.
1. Ensure that nothing rests on your equipment’s cables and that the cables are not located where they can be stepped on, tripped over, or pinched.
Only use attachments or accessories as specified.
Only use the equipment with the cart, stand, tripod, bracket, or table that isspecified by the manufacturer or sold with the apparatus. When a cart is used, use caution to prevent the cart from tipping over and to avoid injury.
Do not connect or disconnect during lightning storms due to risk of electric shock.
If any of the following conditions occur, unplug the equipment from the electrical outlet and replace the part or contact your trained service provider:
The power cable, extension cable, or plug is damaged.
An object has fallen into the equipment.
The equipment has been exposed to water.
The equipment has been dropped or damaged.
The equipment does not operate correctly when you follow the operating instructions.

NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Introduction

The Genie HDMC221V2 is a 2.1MP HD-SDI encapsulated camera with a 3.6mm fixed lens.

Product Features

1/2.8” Progressive Scan CMOS
1080p (1920×1080) @ 30 (25)fps
EX-SDI/HD-SDI/CVBS output
Fixed lens 3.6mm
Electronic Day & Night
WDR, 3D DNR, Defog
RS485 or AD KEY
30x30mm Mini square camera

Product Dimensions

Components

Camera
Mounting bracket
Screws (Tapping and M2)
Operational manual
DIY cable

Mounting Position

Specification

Camera

| Image Sensor| 1/2.8” SONY Exmor R Progressive Scan CMOS
---|---|---

Resolution

| HD-SDI/EX-SDI1.0_2.0_2.1: 1080p @ 30fps (25fps) / 720p @

60fps (50fps) / 720p @ 30fps (25fps) TV out: CVBS NTSC / PAL (720H)

Electronic Shutter| AUTO / FLICKER / MANUAL /(1/30(25)~1/30,000)
Digital Slow Shutter (DSS)| OFF~ x32
Minimum Illumination| 0.2 Lux (F2.0, AGC33dB, DSS:x2)
Lens| 3.6mm, F 2.0, 112.3 (D) x 93.7 (H)x 49.3˚(V) Angle of View
Effective Pixels| 1945(H) x 1097(V)

Functions

Others

| Power Supply| DC12V (±10%)
Power Consumption| Max.150mA @ DC12V
Temperatue| -10°C~+50°C (Operating)

-20°C~+60°C (Storage)

Dimensions| 30 x 30 mm
Weight| Approx.28.9g (Board lens)

Connection

Basic Specification

OSD Manual

genie-HDMC221V2-2.1MP-HD-SDI-Encapsulated-Camera-With-3.6mm-
Fixed-Lens-FIG-4

Convert SDI Output Mode
STEP 1. ENTER

RS485 : Press [LEFT] → [LEFT] → [RIGHT] →[RIGHT] key.
AD-KEY : Press UP/DOWN/LEFT/RIGHT key 3 times.

STEP 2. SELECT

Press UP key 5 times : EX-SDI 2.1
Press DOWN key 5 times : EX-SDI 2.0
Press LEFT key 5 times : HD-SDI
Press RIGHT key 5 times : EX-SDI 1.0

STEP 3. CONFIRM
If the ‘YES’ is not checked within 30sec, the value returns to the previous setting.

Communication Specification

PELCO Protocol for OSD Remote Control PELCO-D

Cam ID : 0x00 ~ Ox1F
ChkSum: The Check Sum is the 8 bit (modulo 256) sum of the payload bytes (Byte2 ~ Byte6) in the Command.
[0x0A-0x3F] means accept any value(between 0x0A – 0x3F) on command action.

PELCO-P