ViewSonic LDS135 Series Direct View LED Display Solution Kit User Guide

ViewSonic LDS135 Series Direct View LED Display Solution Kit

FCC Compliance Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada ICES-003 Compliance
CAN ICES-003(B) / NMB-003(B)

CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU and Radio Equipment Directive 2014/53/EU.

Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC).

Package Contents

LED Display with Motorized Trolley Cart

|  |  | ****

1

|
 |  | |  |
Quick Start
Guide| |

LED Display

| ****

1

Accessory Box

|  |  | ****

1 Box

| •   Remote Control (Black)

x 1

•   Remote Control (Silver)

x 1

•   Anti-Static Gloves x 2

•   Hex Tool x 2 (5 and 8 mm)

•   LAN Cable (5 m) x 1

•   USB-C Cable (3 m) x 1

•   USB Flash Drive x 1

Power Cable

|  |  | ****

1

|
 |  |  |  | ****

The plug is USA

Vacuum

Suction Tool

| 1| standard (category A).

However, a universal

T-Type
Wrench|  | adapter is included.

NOTE

• This product is packed in an air transport box.
• Due to the size and weight, it is recommended that two or more people handle it.

Physical Dimensions for LDS135 Series

Product Overview

Front Panel

Rear Panel

Control Panel for Motorized Trolley Cart

Instructions on Preset Lifting Height

• Initial preset lifting height: Three groups of preset data. The 1/2/3 keys (. , .. , …) correspond to 0 cm / 25 cm / 65 cm height respectively.
• Erasing of preset height data: Height data can be stored for more than 10 years. When new parameters are set, old parameters will be automatically erased.
• How to preset height: at any height (unavailable under the reset and error status), the current height parameters can be preset into keys 1/2/3.

For example, set 25 cm on the 2 key:

Press the S key to display “SET”.
Within 2 seconds, before “SET” disappears, press the 2 (..) key .
When “S-2” is displayed, the setting is over and will return to the previous display.

How to Use Preset Height
At any height (unavailable under the reset and error status), keys 1/2/3 may be used to quickly reach the preset height. If the current height has reached such preset height, no actions will be performed.

How to Change the Height

• Use the “Up” key to lift the display. The lift will automatically stop upon reaching the height limit. Please note, the “Up” key is a “click to act” key, i.e., upon releasing the key the lift will not immediately stop. Instead, it will slow down for a short distance then stop.
• Use the “Down” key to lower the display. The lift will automatically stop upon reaching the height limit. Please note, the “Down” key is a “click to act” key, i.e., upon releasing the key the lift will not immediately stop. Instead, it will slow down for a short distance then stop.

Schematic Diagram of Components

Handling and Moving Flight Cases

Note
During moving, handling, placing and transporting of flight cases, always keep the specified position up, no reversing, in order to prevent bumping and damage to the structure of the equipment and the display components.

1. Before moving any flight case, pull up the brake locks of the six rollers at the bottom, guaranteeing the release of the brake status.
2. Ensure that the group is level, with the height difference less than 1.5 cm, and the ground can comfortably hold more than the weight of the entire equipment.
3. During moving, at least two adults are needed.
   Note: When storing the flight case, ensure the ground is level and that all six rollers are locked.
   Note: For detailed instructions on the equipment, please see the user manual.

Unpacking Operation

Packing and Handling Operation

Specifications

LED Screen

| Type| Direct View LED Display
Size| 135”
Display Area| 118.11” (H) x 66.44” (V)

3,000 mm (H) x 1,687.5 mm(V)

Pixel Pitch| 1.56 mm
Resolution| FHD, 1920 x 1080
Refresh Rate| up to 4440Hz
Contrast Ratio| 6000:1 (Typical)
Brightness| 100-600 cd/m2 (8 levels of adjustments)

Input Signal

|  | 6 x HDMI (1920 x 1080 @ 60Hz, HDCP 2.2)

1 x LAN (RJ45)

3 x USB Type A (2.0)

1 x USB Type C (5V/2A)

1 x IR in

Output Signal

|  | 2 x HDMI (1080p @ 60Hz)

1 x Audio Out (3.5 mm) 3 x USB Type A (Power)

[5V/1.5A x 3]
Speaker Output|  | 20W x 2 Harman Kardon Speakers

Power

| ****

Voltage

| 100-120V/30A ~ 50/60Hz

220-240V/15A ~ 50Hz

(vary by country)

Operating Conditions

| Temperature| 32° F to 104° F (0° C to 40° C)
Humidity| 20%~80% non-condensing
Altitude| ≤ 6,562 ft (2,000 m)

Storage Conditions

| Temperature| -4° F to 140° F (-20° C to 60° C)
Humidity| 10%~90% non-condensing
Altitude| ≤ 6,562 ft (2,000 m)
Physical Dimensions (W x H x D)|  | 1,800~3,010 x 1,963~2,613 x 770 mm (70.87″~118.5” x 77.28″~102.87” x 30.31”)
Weight| Physical| 253 kg (564 lbs)

Power Consumption

| On| 1200W (Normal) 2300W (Max)
Sleep| <0.5W
Off| <0W

NOTE
Product specifications are subject to change without notice.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>