FABTECH FTS24280 Jeep Coil Correction Kit Instruction Manual
- June 4, 2024
- FABTECH
Table of Contents
FTS24280 Jeep Coil Correction Kit
INSTALLATION INSTRUCTIONS
| FTS24280| JEEP COIL CORRECTION KIT
---|---|---
1| FT50912| DRILL GUIDE
2| FT50932| UPPER COIL SPACER
1| FT24280i| INSTRUCTIONS
FTS24280 Jeep Coil Correction Kit
JEEP WRANGLER/GLADIATOR (JL/JT)
FRONT COIL CORRECTION KIT
FTS24280
NOTE: TO ORDER WEARABLE REPLACEMENT COMPONENTS DO NOT USE PART NUMBERS
SHOWN ON THIS INSTRUCTION SHEET. GO TO FABTECH WEBSITE AND LOOK UP WEARABLE
REPLACEMENT PARTS TO FIND THE PROPER PART NUMBER TO ORDER.
Fabtech Motorsports
4331 Eucalyptus Ave. Chino, CA 91710 Tech Line:
909-597-7800
Fax: 909-597-7185
Web: www.fabtechmotorsports.com
TOOL LIST
Required Tools (Not Included)
Basic Hand Tools Floor Jack Jack Stands Assorted Metric and S.A.E sockets, and
Allen wrenches Torque Wrench Drill w/Assorted bits
PRE-INSTALLATION NOTES
For technical assistance call:
909-597-7800 or e-mail:
info@fabtechmotorsports.com
READ THIS BEFORE YOU BEGIN INSTALLATION
Check all parts to the parts list above before beginning installation. If any
parts are missing contact Fabtech at
909-597-7800 and a replacement part
will be sent to you immediately.
Read all instructions thoroughly from start to finish before beginning the
installation. If these instructions are not properly followed severe frame,
driveline, and/or suspension damage may occur.
Check your local city and state laws prior to the installation of this system
for legality. Do not install if not legal in your area.
Prior to the installation of this suspension system perform a front-end
alignment and record. Do not install this system if the vehicle alignment is
not within factory specifications. Check for frame and suspension damage prior
to installation.
The installation of this suspension system should be performed by two
professional mechanics.
This suspension must be installed with Fabtech shock absorbers.
Installation of all fasteners requires the use of provided thread locking
compound with proper torque values as indicated throughout the installation.
Apply thread locking compound upon the final torque of the fastener.
WARNING- Installation of this system will alter the center of gravity of
the vehicle and may increase rollover as compared to stock.
Vehicles that receive oversized tires should check ball joints, uni balls, tie
rod ends, pitman’s arm, and idler arm every 25005000 miles for wear and
replacement as needed.
Verify differential fluid is at the manufactures recommended level prior to
kit installation. Installation of the kit will reposition the differential and
the fill plug hole may be in a different position. (For example, if the
manufacturer recommends 3 quarts of fluid, make sure the diff has 3 quarts of
fluid). Check your specific manual for the correct amount of fluid.
– INSTRUCTIONS –
FRONT SUSPENSION
-
Disconnect the negative terminal on the battery. Jack up the front end of the truck and support the frame rails with jack stands. NEVER WORK UNDER AN UNSUPPORTED VEHICLE! Remove the front tires.
-
On both the Driver and Passenger side, unbolt the front brake line brackets from the frame and the link arm. Save all hardware. SEE FIGURES 1-2. On the driver side unclip the differential breather hose from the upper coil spring mount. SEE FIGURE 3
-
About and remove both driver and passenger side brake line brackets from the axle spring perch. SEE FIGURE 4
-
Disconnect the sway bar end links from the axle. Save hardware.
-
With the axle supported, remove the shocks. Save all hardware. If equipped, remove the bolt mounting the bump stop to the lower coil spring perch. Then, remove the coil with the bump stop. SEE FIGURE 5
-
Remove the upper and lower coil spring isolators. Discard the lower plastic isolator.
-
Locate the FT50912 (Drill Guide). Install the drill guide over the factory bump stop up into the upper coil mount. Make sure the arrow on the drill guide is facing towards the front of the vehicle then mark the two holes for drilling. Remove then drill the marked holes to 1/4″. SEE FIGURES 6-7
-
Reinstall the factory upper isolator so the locating pins install into the new holes drilled. SEE FIGURE 8
-
Install FT50932 (Lower coil bracket) onto the lower factory lower coil mount. SEE FIGURE
-
Reinstall the coil spring with the bump stop spacer using the nut tab and 1/2″ hardware previously removed. Torque to 106 ft-lbs. SEE FIGURE 10
-
Reinstall the shock, sway bars end links, and brake line brackets. Torque the upper/ lower shock mounts to 87 ft-lbs. The sway bar link hardware to 93 ft-lbs and the brake line brackets to 15 ft-lbs
-
Install tires and wheels and torque lug nuts to the wheel manufacturer’s specifications. Turn front tires left to right and check for appropriate tire clearance. Note – Some oversized tires may require trimming of the front bumper & valance.
-
Recheck all bolts for proper torque.
-
Recheck brake hoses, ABS wires, and suspension parts for proper tire clearance while turning tires fully left to right.
-
Install Driver Warning Decal. Complete the product registration card and mail it to Fabtech in order to receive future safety and technical bulletins on this suspension.
Vehicles that will receive oversized tires should check ball joints, uni
balls, and all steering components every 2500-5000 miles for wear and
replacement as required. RETORQUE ALL NUTS, BOLTS, AND LUGS AFTER 50 MILES
AND PERIODICALLY THEREAFTER.
For technical assistance call:
909-597-7800
– Product Warranty and Warnings –
Fabtech provides a Limited Lifetime Warranty to the original retail purchaser
who owns the vehicle, on which the product was originally installed, for
defects in workmanship and materials.
The Limited Lifetime Warranty excludes the following Fabtech items; bushings,
bump stops, ball joints, tie rod ends, limiting straps, cross shafts, Heim
joints, and driveshafts. These parts are subject to wear and are not
considered defective when worn. They are warranted for 60 days from the date
of purchase for defects in workmanship.
Dirt Logic and Performance Coilover take-apart shocks are considered
serviceable shocks with a one-year warranty on leakage only. Service seal kits
are available separately for future maintenance. All other shocks are covered
under our Limited Lifetime Warranty.
Fabtech does not warrant any product for finish, alterations, modifications,
and/or installation contrary to Fabtech’s instructions. Alterations to the
finish of the parts including but not limited to painting, powder coating,
plating, and/or welding will void all warranties. Some finish damage may occur
to parts during shipping, which is considered normal and is not covered under
warranty.
Fabtech products are not designed nor intended to be installed on vehicles
used in race applications or for racing purposes or similar activities. (A
“RACE” is defined as any contest between two or more vehicles, or any contest
of one or more vehicles against the clock, whether or not such contest is for
a prize). This warranty does not include coverage for police or taxi vehicles,
race vehicles, or vehicles used for government or commercial purposes. Also
excluded from this warranty are sales outside of the United States of America.
Installation of most suspension products will raise the center of gravity of
the vehicle and will cause the vehicle to handle differently than stock. It
may increase the vehicle’s susceptibility to a rollover, on-road and off-road,
at all speeds. Extreme care should be taken to operate the vehicle safely at
all times to prevent rollover or loss of control resulting in serious injury
or death. Fabtech front-end Desert Guards may impair the deployment or
operation of vehicles equipped with supplemental restraining systems/air bag
systems and should not be installed if the vehicle is equipped as so.
Fabtech makes every effort to ensure the suspension product compatibility with
all vehicles listed on the website, but due to unknown auto manufacturer’s
production changes and/or inconstancies by the auto manufacturer, Fabtech
cannot be responsible for 100% compatibility, including the fitment of tire
and wheel sizes listed. The Tire and Wheel sizes listed in Fabtech’s website
are only a guideline for street driving with noted fender trimming. Fabtech is
not responsible for damages to the vehicle’s body or tires. Fabtech is not
responsible for premature wear of factory components due to the installation
of oversized tires and wheels.
Fabtech’s obligation under this warranty is limited to the repair or
replacement, at the Fabtech option, of the defective product only. All costs
of removal, installation or re-installation, freight charges, and incidental
or consequential damages are expressly excluded from this warranty. Fabtech is
not responsible for damages and/or warranty of other vehicle parts related or
nonrelated to the installed Fabtech product. This warranty is expressly in
lieu of all other warranties expressed or implied. This warranty shall not
apply to any product that has been subject to accident, negligence,
alteration, abuse or misuse as determined by Fabtech.
Fabtech suspension components must be installed as a complete system including
shocks as shown on our website. All warranties will become void if Fabtech
parts are combined and/or substituted with other aftermarket suspension
products. Combination and/or substitution of other aftermarket suspension
parts may cause premature wear and/or product failure resulting in an accident
causing injury or death. Fabtech does not warrant products not manufactured by
Fabtech.
Depending on the condition of the factory suspension components retained after
the installation of a Fabtech suspension not all vehicles may have the same
ride stance front to rear as described in the website. The blue color of
suspension components shown in all Fabtech photographs are for display
purposes only. The majority of all Fabtech components will be black
specifically where noted with part numbers ending in BK.
Installation of Fabtech products may void the vehicle’s factory warranty; it
is the consumer’s responsibility to check with their local vehicle’s dealer
for warranty disposition before the installation of the product. Some state
laws may prohibit the modification of suspension to a vehicle in whole or in
part. It is the responsibility of the installer and consumer to consult local
laws prior to the installation of any Fabtech suspension product to comply
with such written laws.
It is the responsibility of the distributor and/or the retailer to review all
warranties and warnings of Fabtech products with the consumer prior to
purchase.
Fabtech reserves the right to super cede, discontinue, change the design,
finish, part number and/or application of parts when deemed necessary without
written notice. Fabtech is not responsible for misprints or typographical
errors within the website or price sheet. For the most recent Product Warranty
and Warnings visit our website
www.fabtechmotorsports.com
Instruction Sheet Part# – FT24280i
09/02/21
Documents / Resources
|
FABTECH FTS24280 Jeep Coil Correction
Kit
[pdf] Instruction Manual
FTS24280, Jeep Coil Correction Kit, FTS24280 Jeep Coil Correction Kit, Jeep
Wrangler Gladiator Front Coil Correction Kit
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>