Holmes 17046 10 Inch Table Fan Instruction Manual
- June 13, 2024
- Holmes
Table of Contents
Instruction Manual
Item: 17046
Model: 32510016
10 Inch
Metal Table Fan
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be taken including the following:
-
Read all instructions before using this appliance.
-
Use fan only for purposes described in the instruction manual.
-
To protect against electrical shock do not immerse unit, plug or cord in water or spray with liquids and plug the appliance directly into a 120V AC electrical outlet.
-
Close supervision is necessary when any appliance is used by or near children.
-
Unplug from outlet when not in use, when moving fan from one location to another, before putting on or taking off parts and before cleaning.
-
Avoid contact with moving parts.
-
Do not operate in the presence of explosive and/or flammable fumes.
-
To avoid fire hazard, NEVER place the cord under rugs or any parts near an open flame, cooking or other heating appliance.
-
Do not operate any appliance with a damaged cord or plug after the appliance malfunctions, or has been dropped/damaged in any manner. Discard fan or contact customer service.
-
Do not run cord under carpeting. Do not cover cord with throw rugs, runner, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
-
The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
-
Do not let the cord hang over the edge of a table, counter or come in contact with hot surfaces or leave exposed to high traffic areas.
-
Do not use outdoors.
-
To disconnect, grip plug and pull from wall outlet.
Never yank on cord. -
Always use on a dry, level surface.
-
Do not operate fan until fully assembled with all parts properly in place.
-
This product is intended for household use ONLY and not for commercial or industrial applications.
-
WARNING: To reduce the risk of electrical shock and injury to persons, do not use in window.
-
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
-
This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short circuit may be present and the product should be discarded or contact customer service.
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To
reduce the risk of electric shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician to install the
proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY.
FEATURES
ASSEMBLY
Your Table Fan comes completely assembled and is ready for use.
OPERATING INSTRUCTIONS
- Set the fan base on a dry, level surface.
- Make sure the Speed Control Knob (F) is in the OFF (0) position.
- Plug cord into any standard 120 volt AC outlet.
- To adjust the speed, turn the speed control knob (F) to the desired setting, 0-3-2-1.
- To start OSCILLATION, press control knob (G) down. To stop oscillation, pull control knob up.
TILT ADJUSTMENT
- Loosen the tilt-adjustment knob and move the fan head to the desired angle.
- Tighten the knob by turning clockwise.
CLEANING / MAINTENANCE
FAN CLEANING
- Always unplug the fan before cleaning.
- Do not allow water to drip on or into the fan housing.
- Use only a soft cloth moistened with a mild soap solution.
- Do not use harsh chemicals such as gasoline, thinner or benzene as a cleaner.
- Do not attempt to remove the fan blade.
- Please use caution around the motor housing area. Do not allow the motor or other electrical components to be exposed to water.
FAN BLADE CLEANING
- Remove the front grill by opening the clips located around the perimeter.
- Remove the blade by loosening the securing screws.
- Clean the fan blade, front and rear grills with a soft cloth moistened with a mild soap solution.
- Replace the fan blade and tighten the securing screw.
- Securely fasten the front grill to the rear grill by closing the clips over the perimeter.
FAN HEAD AND BASE CLEANING
- Using a soft, moist cloth, with or without a mild soap solution, carefully clean the fan base (I) and head (C).
Use CAUTION around the motor housing area.
Do not allow the motor or other electrical components to be exposed to water.
FAN STORAGE
- Store the fan in a clean, dry location between seasons or when not in use for an extended period.
- Keep the fan head protected from dirt and dust during storage.
If you have any questions regarding your product or would like to learn more
about other Holmes ® products, please visit our website at
www.getholmesfans.com or call customer
service: 1-866-769-3166 (8:30 am – 5:00
pm E.S.T.) or send
an email to info@getholmesfans.com. For
inquiries
regarding recycling and proper disposal of this product, please contact your
local waste management facility.
MAINTENANCE
USER SERVICING INSTRUCTIONS
Follow these instructions to safely and correctly care for your fan.
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please visit our website at
www.getholmesfans.com for information on how
to order a new fuse.
REPLACING THE FUSE
-
Unplug your fan.
Grasp plug and remove from the receptacle or other outlet device.
NOTE: Do not unplug by pulling on cord. -
Open fuse cover, located on the top of the plug, by using your thumb or a flathead screwdriver to slide the cover towards the prongs.
NOTE: Ensure the fuse cover is completely open before attempting to remove fuse. -
Remove fuse carefully by using a small screwdriver to pry it from the compartment at the metal ends of the fuse. (See Figure 2)
-
Place plug on a solid, flat surface. Insert new 5 Amp, 125 Volt fuse into fuse compartment. Use a small screwdriver to secure the metal ends of the fuse into the compartment.
CAUTION: Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse. -
Slide fuse cover closed completely.
NOTE: If fuse cover is difficult to close, make sure the fuse is completely secured in place by pressing on metal ends of the fuse.
CAUTION: Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.
WARRANTY INFORMATION
3 YEAR LIMITED WARRANTY
This device has a limited warranty of 3 years from the original date of
purchase against workmanship and defects in material. If under normal use,
your product fails to operate, please contact our customer service department
at info@getholmesfans.com. A refund or replacement will be provided to you
with proof of purchase. Star Elite Inc. may deny claims of damage caused by
misuse or modifications of this product.
How to Obtain Warranty Service
If you have any problems, please do not contact the store.
Contact our customer service at
1-866-769-3166
(8:30 am – 5:00 pm EST) Monday – Friday or contact us at
info@getholmesfans.com.
Our customer service will be happy to assist you.
www.getholmesfans.com
© 2021 Sunbeam Products, Inc. All rights reserved.
HOLMES ® is a registered trademark of Sunbeam Products, Inc. used under
license. Distributed by Star Elite Inc., Montreal, Canada H3B 3X9
SEH009-112221
Printed In China