Holmes 32510111 Twin Window Fan Instruction Manual
- June 13, 2024
- Holmes
Table of Contents
Instruction Manual
Item: 12080
Model: 32510111
Twin Window
Fan
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be taken including the following:
- Read all instructions before using this appliance.
- Use fan only for purposes described in the instruction manual.
- To protect against electrical shock do not immerse unit, plug or cord in water or spray with liquids and plug the appliance directly into a 120V AC electrical outlet.
- Close supervision is necessary when any appliance is used near children.
- Not intended for use by children.
- Unplug from outlet when not in use, when moving fan from one location to another, before putting on or taking off parts and before cleaning.
- Avoid contact with moving parts.
- Do not operate in the presence of explosive and/or flammable fumes.
- To avoid fire hazard, NEVER place the cord under rugs or any parts near an open flame, cooking or other heating appliance.
- Do not operate any appliance with a damaged cord or plug after the appliance malfunctions, or has been dropped/damaged in any manner. Discard fan or contact customer service.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runner, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
- The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
- Do not let the cord hang over the edge of a table, counter or come in contact with hot surfaces or leave exposed to high traffic areas.
- Do not use outdoors.
- To disconnect, grip plug and pull from wall outlet. Never yank on cord.
- Always use on a dry, level surface.
- Do not operate fan until fully assembled with all parts properly in place.
- This product is intended for household use ONLY and not for commercial or industrial applications.
- WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
- This product employs overload protection (fuse).
A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short circuit may be present and the product should be discarded or contact customer service.
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
| THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To
reduce the risk of electric shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician to install the
proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY.
---|---
WINDOW INSTALLATION
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS FROM THE PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR PARTS THAT COULD BE REQUIRED TO OPERATE THIS FAN.
- The window fan comes fully assembled and is ready for immediate window installation.
- Before installation, familiarize yourself with the 6 inch (15cm) built-in extender (A) on both side of the fan housing (see Figure 1).
NOTE: IT IS RECOMMENDED KEEPING YOUR WINDOW SCREEN IN PLACE.
For double-hung windows (designed to fit windows with minimum openings of
23.25 inches (60cm) wide and 11.75 inches (30cm) high
-
Align the Window Fan horizontally in the window and the Built-In-Extender Panels on both sides.
-
With the window open at least 12 inches, take an accurate measurement of the opening where the unit will be placed.
-
Match your window measurement with the INSTALLATION GUIDE (SEE NEXT SECTION).
-
Set the fan in the window.
Identify the front and back sides of the fan.
For Fresh Air Operation (draw in fresh air from the outside), position the fan so the front side faces you. See silkscreen indicator under control dial “This Side – Fresh Air In”.
For Exhaust Air Operation (pulls inside air out of the room), position the fan so the back side faces you.
See silkscreen indicator under control dial “This Side – Exhaust Out”. -
Carefully close the window onto the top of the fan so that the bottom edge of the window rests behind top line of fan housing. This helps keep the fan in place.
-
Feet (D) should not be installed when mounting in window.
INSTALLATION GUIDE
For 23.25 inches (60cm) to 29.25 inches (74cm): Use up to 6 inches (15cm) of
either side, pull out extender panel.
For 29.25 inches (74cm) to 35.25 inches (89cm): Use up to 6 inches (15cm) of
both side, pull out extender panels.
A. 6 inches (15cm) Built-in Extender
Panels
B. Top Window Support
C. 2 Speed Motor Control
D. Fan Feet
WARNING: BE SURE THE FAN IS SECURELY INSTALLED IN YOUR WINDOW AT ALL
TIMES.
DO NOT LEAN OR PUSH ON THE FAN WHILE IT IS IN THE WINDOW.
OPERATING INSTRUCTIONS
OPERATION GUIDE
- Make sure rotary switch is in the OFF position.
- Plug into 120V AC electric outlet.
- To start the unit, turn the rotary switch (C) to desired speed high (II) or low (I).
- Unplug fan when not in use.
- To use in EXHAUST mode, manually turn the unit around so that the rotary switch reads “ THIS SIDE EXHAUST OUT. (Controls can be operated from both sides.)
INSTRUCTIONS FOR FLOOR OR TABLE USE:
- Simple assembly is required to use this fan on a table or floor.
- Locate 4 slots on the base of fan (See Fig. 2). Push fan foot into slot to lock in place.
- Repeat this action on the other foot.
CLEANING / MAINTENANCE
USER SERVICING INSTRUCTIONS REPLACEABLE FUSE
If the (5 Amp, 125 Volt) replaceable fuse blows, please visit our website at
www.getholmesfans.com for information on how to order a new fuse.
REPLACING THE FUSE
-
Unplug the fan. Grasp plug and remove from the receptacle or other outlet device.
NOTE: Do not unplug by pulling on cord. -
Open fuse cover, located on the top of the plug, by using your thumb or a flathead screwdriver to slide the cover towards the prongs.
NOTE: Ensure the fuse cover is completely open before attempting to remove fuse. -
Remove fuse carefully by using a small screwdriver to pry it from the compartment at the metal ends of the fuse. (See Figure 3)
-
Place plug on a solid, flatsurface. Insert new 5 Amp,125 Volt fuse into fuse compartment. Use a small screwdriver to secure the metal ends of the fuse into the compartment.
CAUTION: Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse. -
Slide fuse cover closed completely.
NOTE: If fuse cover is difficult to close, make sure the fuse is completely secured in place by pressing on metal ends of the fuse.
CAUTION: Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.
CLEANING/MAINTENANCE
Follow these instructions to correctly and safely care for this window fan.
FAN CLEANING
- Always unplug the fan before cleaning or disassembling.
- Do not allow water to drip on or into the fan motor housing.
- Use only a soft cloth moistened with a mild soap solution.
- Do not use harsh chemicals such as gasoline, thinner or benzene as a cleaner.
- Do not attempt to remove the fan blade.
- Use CAUTION around the motor housing area. Do not allow the motor or other electrical components to be exposed to water.
- It is recommended to periodically clean this fan by lightly running a vaccum cleaner nozzle over the fan grill to remove any dust or dirt that may have accumulated inside or on the unit.
FAN STORAGE
- It is recommended to use the original (or appropriately sized) box.
- Protect the fan from dirt, dust, and moisture.
For inquiries regarding recycling and proper disposal of this product, please contact your local waste management facility.
WARRANTY INFORMATION
3 YEAR LIMITED WARRANTY
This device has a limited warranty of 3 years from the original date of
purchase against workmanship and defects in material. If under normal use,
your product fails to operate, please contact our customer service department
at info@getholmesfans.com. A refund or
replacement will be provided to you with proof of purchase. Star Elite Inc.
may deny claims of damage caused by misuse or modifications of this product.
Warranty Service
Contact our customer service at getholmesfans.com/en/contact-
us or
info@getholmesfans.com or
1-866-769-3166 (8:30 am – 5:00 pm EST)
Monday-Friday.
Our team will be happy to assist.
www.getholmesfans.com
© 2022 Sunbeam Products, Inc. All rights reserved.
HOLMES® is a registered trademark of Sunbeam Products, Inc. used under
license.
Distributed by Star Elite Inc., Montreal, Canada H3B 3X9
SEH021-120622
Printed In China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>