MuxLab 500408 HDMI 2.0 Extender Kit User Manual

MuxLab 500408 HDMI 2.0 Extender Kit

Safety Precautions

To ensure the best performance from the product, please read all instructions carefully before using the device. Save this manual for future reference.

• Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burns.
• Do not open or remove the housing of the device as you may be exposed to dangerous voltage or other hazards.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture and do not install this product near water. Keep the product away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on the housing, unplug the module immediately.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Using supplies or parts not meeting the product specifications may cause damage, deterioration or malfunction.
• Refer all servicing to qualified service personnel.
• Install the device in a place with adequate ventilation to avoid damage caused by overheat.
• Unplug the power when left unused for a long period of time.
• Information on disposal of devices: do not burn or mix with general household waste, please treat them as normal electrical waste.

Copyright Notice
All contents in this manual are copyrighted, and cannot be cloned, copied, or translated without the express permission of MuxLab Inc. Product specifications and information in this document are for reference only, and the content may be updated from time to time without prior notice.

Introduction

The HDMI 2.0 Extender Kit, 50m (Model: 500408) allows extend a high-definition video/ audio signals and one-way IR commands up to 164ft/50m between the transmitter and receiver over a single Cat5e/6 cable. This extender supports up to 4K/60Hz 4:4:4 video resolution, 18Gbps bandwidth, HDCP 2.2., HDMI Loop- out on the Transmitter, and one-way IR pass-through enabling source control.

The extender includes one Transmitter unit and Receiver unit. The Transmitter unit is responsible for capturing HDMI input signal and carries the signal via one Cat5e/6 cable, and emitting IR control signals. The Receiver unit is responsible for receiving the HDMI signal and capturing IR control signals.

Features

• HDMI 2.0, HDCP 2.2 / HDCP 1.4 and DVI 1.0 compliant
• Supports 18Gbps bandwidth
• Supports input and output video resolution up to 4K/60Hz 4:4:4, extends distance up to 164ft /50m
• Supports one HDMI loop output
• Supports one-way IR pass-through
• Supports HDR function
• Supports PoC (Power over Cable) function, it means that either transmitter or receiver is powered supply by 12VDC/1A power adapter, the other doesn’t need power supply
• Supports automatic copy EDID function
• Compact design for easy and flexible installation

Package Contents

• One (1) HDMI 2.0 Extender (Transmitter)
• One (1) HDMI 2.0 Extender (Receiver)
• One (1) IR Blaster cable (1.5 meters)
• One (1) 20~60KHz IR Receiver cable(1.5 meters)
• One (1) 12VDC/1A Locking Power adapter
• Four (4) Mounting Ears
• One (1) User manual (available via download)

Notes: Confirm that the product and accessories are all included. If not, please contact the supplier from which you purchased the unit.

Specifications

Technical

HDMI Compliance.| HDMI 2.0
HDCP Compliance| HDCP 2.2 / HDCP 1.4
Video Bandwidth| 18Gbps
Video Resolution| Up to 4K/60Hz 4:4:4
Color Space| RGB / YCbCr 4:4:4, YCbCr 4:2:2/4:2:0, YUV 4:4:4
Color Depth| 8/10/12-bit (1080P/60Hz, 4K/30Hz, 4K/60Hz YCbCr 4:2:2/4:2:0) 8-bit (4K/60Hz 4:4:4 )
HDMI Audio Formats| LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD, Dolby Digital Plus(DD+), DTS-ES, DTS HD Master, DTS HD-HRA, DTS-X
ESD Protection| Human body model — ±8kV (Air-gap discharge) & ±4kV (Contact discharge)
Connection
Transmitter| Inputs: 1 x HDMI Type A [19-pinfe male] 1 x SERVICE [Micro USB, Update port] Outputs: 1 x HDMI Type A [19-pin female] 1 x IR OUT [3.5mm Stereo Mini-jack] 1 x CAT OUT [RJ45, 8-pin female
Receiver| Inputs: 1 x IR IN [3.5mm Stereo Mini-jack] 1 x CAT IN [RJ45, 8-pin female] 1 x SERVICE [Micro USB, Update port] Outputs: 1 x HDMI Type A [19-pin female]
Mechanical
Housing| Metal Enclosure
Color| Black
Dimensions| Transmitter / Receiver: 61mm [W] x 88mm [D] x 18mm [H]
Weight| Transmitter: 160g, Receiver: 155g
Power Supply| Input: 100 – 240VAC 50/60Hz Output: 12VDC/1A
Power Consumption| 3.84W
Operating Temperature| 32 – 104°F / 0 – 40°C
Storage Temperature| -4 – 140°F / -20 – 60°C
Relative Humidity| 20 – 90% RH (no condensation)
Generic Specification
Warranty| 2 years
Order Information| 500408 HDMI 2.0 Extender Kit, 50M (UPC: 627699004081)

Operation Controls and Functions

Transmitter Panel

or Projector with an HDMI cable
2| HDMI IN| HDMI input port, connect to HDMI source device such as DVD or PS4 player with an HDMI cable
3| CAT OUT| Connect to CAT IN port on the receiving end with a CAT6 cable
4| Power Indicator Lamp (Green)| The LED will illuminate when the transmitter is powered on
5| Data signal Indicator Lamp (Orange)| The LED will illuminate when the transmitter and the receiver have signal transmission
6| Service port| Firmware update port
7| IR OUT| Connect to wideband IR Blaster cable. The IR signal is from the IR IN port of the receiver
8| 12VDC| Plug 12VDC/1A power supply into the unit and connect the adapter to an AC outlet. (Note: The extender supports PoC function, it means that either transmitter or receiver is powered on by the 12VDC/1A power adapter, the other doesn’t need power supply)

Receiver Panel

Projector with an HDMI cable
2| CAT IN| Connect to CAT OUT port on the transmitter end with a CAT6 cable
3| Power Indicator Lamp (Green)| The LED will illuminate when the receiver is powered on
4| Data signal Indicator Lamp (Orange)| The LED will illuminate when the transmitter and the receiver have signal transmission
5| Service port| Firmware update port
6| IR IN| Connect to wideband IR Receiver cable. The IR signal will send to the IR OUT port of the transmitter
7| 12VDC| Plug 12VDC/1A power supply into the unit and connect the adapter to an AC outlet. (Note: The extender supports PoC function, it means that either transmitter or receiver is powered on by the 12VDC/1A power adapter, the other doesn’t need power supply)

IR Pin Definition

IR Receiver and Blaster pin’s definition as below:

The following is a diagram about the use method of IR cable.

Application Example

Customers Support

HDMI 2.0 Extender Kit, 50M
500408

Follow us:

2321 Cohen | St-Laurent , H4R 2N7 | Québec, Canada Tel: 514-905-0588 | Fax:
514-905-0589 | Toll free: 1-877-689-5228 [email protected] |
[email protected] | www.muxlab.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>