Lucci decor 030679 North 3 Light Pendant in Black Instruction Manual

: June 5, 2024
: Lucci decor

Table of Contents

Lucci decor 030679 North 3 Light Pendant in Black
Installation Requirements
Installation Directions
Safety Tips
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Lucci decor 030679 North 3 Light Pendant in Black

Installation Requirements

This luminaire must be assembled and installed by a licensed electrician.
All wiring and installation of the luminaire must adhere to the latest local and national wiring rules.E.g. AS/NZS 3000 Electrical Installations.
This luminaire is a Class I product and must be earthed during wiring and installation.
Do not exceed the maximum wattage rating.
Select a suitable location for installation:
- This luminaire is suitable for indoor use only.
- The mounting point must support 2 times the weight of the luminaire.
- Ensure the luminaire is not installed in the direct line of an air vent/system.
- If installing a luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
Take care not to pull any electrical wires during unpacking as this may damage the connection.
Lay out all the components on a smooth surface and make sure no components are missing before assembling.
If parts are missing, return the complete product to the place of purchase for inspection or replacement.
Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears
damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation Directions

NOTE : Due to the size/weight/wiring of the luminaire, two people will be required to lift it up during the installation process.

Remove all packaging material from the product and be careful not to throw away accessories that may be hidden
within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.
Remove the mounting bracket (B) from the canopy (G) by loosening the nuts (I) at the front.
Use the mounting bracket (B) as a template to mark the screw positions on the ceiling.
Install the mounting bracket (B) onto the ceiling by using appropriately sized mounting screws (D), washers (C) and anchors (A). Ensure the screws (D), washers (C) and anchors (A) used are suitable for the mounting surface and the surrounding environment.
Determine the length of the suspension rod required for your installation location. Install the required lengths of suspension rod (O, L, K, J) onto the body (P) of the luminaire.
Insert the plastic grommets (M) into both ends of the threaded rods (N) and join the suspension rods together (O, L,
K, J).
NOTE : Pull the cord out as you install the suspension rods (O, L, K, J) to remove any slack. Take care, not to cross-thread or twist and damage the cord.
Install the joiners (H) to the top of the suspension rod and install the canopy (G).
NOTE : Ensure that the star washer, earth ring, lock washer and nut are installed in the correct sequence.
Connect the mains supply wires to the terminal block (E).
NOTE : Ensure the wires are secure, and no bare wires are exposed.
NOTE : This luminaire is a Class I product and must be earthed during wiring and installation.
NOTE : Ensure the earth wires from the mounting bracket (B) and the canopy (G) are connected to the earth terminal block (E) and there is full continuity.
Install the canopy (G) back onto the mounting bracket (B) and secure it by tightening the nuts (I).
Install globes (R – not included) into the lamp holders (Q). Do not exceed the maximum wattage rating.
After the installation, switch on the luminaire to test and enjoy your new lighting product.

Safety Tips

Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning,
changing the globe or making any adjustment to the luminaire.
To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
Select a suitable location away from liquids and hazards.
To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.