SYLVANIA 4056575 Linear High Bay Installation Guide
- June 13, 2024
- SYLVANIA
Table of Contents
SYLVANIA 4056575 Linear High Bay
INSTALLATION
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODES BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. THIS PRODUCT MUST BE WIRED IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE AND ALL APPLICABLE LOCAL CODES.
-
TO PREVENT PERSONAL INJURY OR PRODUCT DAMAGE ONLY LICENSED ELECTRICIANS SHOULD PROVIDE ALL INSTALLATION SERVICES.
-
TO AVOID ELECTRIC SHOCK OR COMPONENT DAMAGE DISCONNECT POWER BEFORE ATTEMPTING INSTALLATION OR SERVICING.
-
USE CAUTION WHEN HANDLING THIS PRODUCT DURING OR AFTER OPERATION AS IT MAY BECOME HOT AND CAUSE BURNS. DISCONNECT PRODUCT AND ALLOW COOLING PRIOR TO SERVICING.
-
ANY ALTERATION OR MODIFICATION OF THIS PRODUCT IS EXPRESSLY FORBIDDEN AS IT MAY CAUSE
SERIOUS PERSONAL INJURY, DEATH, PROPERTY DAMAGE AND/OR PRODUCT MALFUNCTION. -
TO PREVENT PRODUCT MALFUNCTION AND / OR ELECTRICAL SHOCK THIS PRODUCT MUST BE PROPERLY GROUNDED.
-
THIS LUMINAIRE IS DESIGNED TO OPERATE IN AMBIENT TEMPERATURES RANGING FROM -4°F TO +122°F (-20°C TO +50°C)
-
THIS LUMINAIRE IS DESIGNED TO OPERATE IN DRY OR DAMP LOCATIONS
-
MIN 90°C SUPPLY CONDUCTORS
-
TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR OTHER SHARP OBJECTS.
NOTE!
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:(1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Please visit www.ledvanceUS.com\fccpart15b CAN
ICES-005(B) \ NMB5(B)
90 -165W UNV; 110W HUV
165W HUV
220W UNV
220W HUV
300W UNV; 320W HUV
SAFETY PRECAUTIONS
IMPORTANT: READ CAREFULLY BEFORE INSTALLING THE FIXTURE. RETAIN FOR FUTURE
REFERENCE.
GENERAL: Upon receipt of the fixture, thoroughly inspect for any freight
damage which should be brought to the attention of the delivery carrier.
TO AVOID ELECTRIC SHOCK OR COMPONENT DAMAGE DISCONNECT POWER BEFORE ATTEMPTING
INSTALLATION OR SERVICING
INSTALLATION
A : Installation Using Supplied 3-foot chain and V-hooks
B : Installation Using Optional Surface/Pendant Mounting Brackets (65673, 65674)
C : Installation Using Optional Pendant Mounting Bracket (65675, 65676)
D. Connect the supply wires to the fixture according to the National
Electric Code and all applicable State and Local codes.
E. Installation is now complete. Turn on the power at circuit breaker or
fuse box then turn the light switch to power the fixture.
F. Installation of Optional Motion Sensor NAED 65622
Gently screw motion sensor 65622 into the threads of the sensor housing.
Finger tighten the sensor ONLY, Do Not overtighten the sensor as damage may occur
Default sensor settings*:
| Detection Area | 100% |
|---|---|
| Hold Time | 5 Minutes |
| Daylight Threshold | 50 Lux |
| Stand-by Period | 60 Minutes |
| Stand-by Dimming | 30% |
*Note: Changing the sensor settings can only be achieved using the optional remote – NAED 65623
Wiring Diagram
This fixture is compatible with 0-10V output dimming controls (please
reference Dimmable Compatibility List LEDLUM012). To get to 0% light output
(OFF) it is necessary to switch the input power to the LED drivers.
Connect wall dimmer to dimming wires on driver. (See Wiring Diagram)
Wiring Diagram
Emergency Wiring Diagram – Switched
Emergency Wiring Diagram – Un-Switched
CLEANING AND MAINTENANCE
- To maintain the fixture efficacy occasional cleaning of the outer lens surface may be needed.
- Use a mild soap or detergent, which is essentially neutral pH (pH approximately 6 to 8), nonabrasive, and which contains no chlorinated or aromatic hydrocarbons.
- Wash thoroughly, using a soft cloth.
- Rinse with clean, cold water and wipe dry.
TROUBLE SHOOTING CHECKLIST: If luminaire does not work
- Check your power source.
- Check electrical connections.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>