milwaukee M12 FBFL10 10mm Brushless Belt Sander File Instruction Manual
- June 13, 2024
- Milwaukee
Table of Contents
milwaukee M12 FBFL10 10mm Brushless Belt Sander File
Operating Instructions
Remove the battery pack before starting any work on the machine.
TECHNICAL DATA
TECHNICAL DATA
| M12 FBFL10| M12 FBFL13
---|---|---
Type
| Bandile|
Bandile
Production code| 4919 22 01 XXXXXX MJJJJ|
4919 32 01 XXXXXX MJJJJ
Battery voltage
| 12 V ⎓| 12 V ⎓
Belt speed, high speed| 0 – 18,5 m/s|
0 – 18,4 m/s
Belt speed, low speed
| 0 – 9,2 m/s| 0 – 9,3 m/s
Belt width| 10 mm / 3/8″|
13 mm / 1/2″
Belt length
| 330 mm / 13″| 457 mm / 18″
Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah … 6,0 Ah)| 1,0 … 1,2
kg|
1,1 … 1,3 kg
Recommended Ambient Operating Temperature
| 18 … +50 °C| 18 … +50 °C
Recommended battery types| M12B…|
M12B..
Recommended charger
| C12C; M12-18…; M12C4; M12TC|
C12C; M12-18…; M12C4; M12TC
Noise information Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are: Sound pressure level /
Uncertainty K Sound power level / Uncertainty K| 70 dB (A) / 3 dB (A) 81 dB
(A) / 3 dB (A)| 68 dB (A) / 3 dB (A) 79 dB (A) / 3 dB (A)
---|---|---
Wear ear protectors!
Vibration information Vibration total values (triaxial vector sum)
determined according to EN 62841 Vibration emission value ah / Uncertainty K|
2,16 m/s2 / 1,5 m/s2| 1,69 m/s2 / 1,5 m/s2
WARNING!
The vibration and noise emission level given in this information sheet has
been measured in accordance with a standardized test given in EN 62841 and may
be used to compare one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration and noise emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration
and noise emission may differ. This may significantly increase the exposure
level over the total working period.
An estimation of the level of exposure to vibration and noise should also take
into account the times when the tool is switched off or when it is running but
not actually doing the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the operator from the effects
of vibration and/or noise such as: maintain the tool and the accessories, keep
the hands warm, organization of work patterns.
WARNING! Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR SANDERS
Collected sanding dust from sanding surface coatings such as polyurethanes, linseed oil, etc. can self-ignite in the vacuum cleaner bag or elsewhere and cause fire. To reduce the risk of fire always empty the vacuum cleaner bag frequently (10-15 minutes) while sanding and never store or leave a vacuum cleaner without totally emptying its vacuum cleaner bag. Also follow the recommendations of the coatings manufacturers.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions will reduce personal
injuries.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch
the device on again while the insertion tool is stalled, as doing so could
trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying heed to the
safety instructions.
The possible causes may be:
- it is tilted in the workpiece to be machined
- it has pierced through the material to be machined
- the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool is sharp-edged and can become hot during use.
WARNING! Danger of cuts and burns
- when handling the insertion tools
- when setting the device down.
Wear protective gloves when handling insertion tools.
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or floor, take care to avoid electric cables
and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause
severe injury and damage.
Remove the battery pack before starting any adjustment, cleaning and
maintenance work on the device.
WARNING! To reduce the risk of fire, personal injury, and product damage
due to a short circuit, never immerse your tool, battery pack or charger in
fluid or allow a fluid to flow inside them. Corrosive or conductive fluids,
such as seawater, certain industrial chemicals, and bleach or bleach
containing products, etc., Can cause a short circuit.
Never break open battery packs and chargers and store only in dry rooms. Keep
dry at all times.
Use only System M12 chargers for charging System M12 battery packs. Do not use
battery packs from other systems.
SPECIFIED CONDITIONS OF USE
The belt sander can be used for sanding wood, plastic, metal, filler and
painted surfaces.
This machine is suitable only for dry sanding.
Do not use the product in any way other than those stated for intended use.
RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:
- Injury caused by vibration. Hold the product by designated handles and restrict working time and exposure.
- Exposure to noise can cause hearing injury. Wear ear protection and limit exposure.
- Injury due to flying debris. Wear eye protection, heavy long trousers and substancial footwear at all times.
- Inhalation of toxic dusts.
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Battery packs which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery
pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged, after
use.
To obtain the longest possible battery life remove the battery pack from the
charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from
moisture Store the battery packs in a 30% – 50% charged condition
Every six months of storage, charge the pack as normal.
Battery protection for Li-Ion batteries
In extremely high torque, binding, stalling and short circuit situations that
cause high current draw, the tool will vibrate for about 5 seconds, the fuel
gauge will flash, and then the tool will turn OFF.
To reset, release the trigger. Under extreme circumstances, the internal
temperature of the battery pack could raise too much. If this happens, the
fuel gauge will flash until the battery pack cooled down. After the lights go
off, the work may continue.
Transporting Lithium Batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
The user can transport the batteries by road without further requirements.
Commercial transport of Lithium-Ion batteries by third parties is subject to
Dangerous Goods regulations. Transport preparation and transport are
exclusively to be carried out by appropriately trained persons and the process
has to be accompanied by corresponding experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated to prevent
short circuit.
Ensure that battery pack is secured against movement within packaging. Do not
transport batteries that are cracked or leak.
Check with forwarding company for further advice.
WORKING INSTRUCTIONS
The stock removal rate during sanding and the surface finish are essentially
determined by the choice of sanding belt and the preselected belt speed. The
higher the belt speed, the higher the stock removal and the finer the sanding
surface.
Only flawless abrasive belts produce good sanding performance and protect the
power tool. If possible, work with a low contact pressure to increase the
service life of the sanding belts. The dead weight of the power tool is
sufficient for good sanding performance. Excessive increase of the contact
pressure does not result in higher sanding performance, but in greater wear of
the power tool and the sanding belt.
Place the power tool switched on on the surface to be machined.
Work at a moderate feed rate and carry out the sanding process parallel and
overlapping to the sanding paths. Sand in the direction of the grain,
crosswise sanding tracks result in disturbing sanding effects.
Particularly when sanding off paint residues, these may melt and smear the
material surface and the sanding belt. Therefore, work with dust extraction.
A sanding belt with which metal has already been processed should not be used
for other materials.
Only store abrasive belts in a hanging position and do not bend them,
otherwise they will become unusable.
Preselect belt speed
The required belt speed depends on the material and the working conditions and
can be determined using practical tests.
CLEANING
The ventilation slots of the machine must be kept clear at all times.
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts. Should components
need to be replaced which have not been described, please contact one of our
Milwaukee service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
Article No. as well as the machine type printed on the label and order the
drawing at your local service agents or directly at: Techtronic Industries
GmbH, Max‑Eyth‑Straße 10, 71364 Winnenden, Germany
| Please read the instructions carefully before starting the machine.
---|---
| CAUTION! WARNING! DANGER!
| Remove the battery pack before starting any work on the appliance.
| Always wear goggles when using the machine.
| Wear a suitable dust protection mask.
| Wear a suitable dust protection mask.
| Accessory – Not included in standard equipment, available as an accessory.
| Do not dispose electric tools, batteries/rechargeable batteries together
with household waste material. Electric tools and batteries that have reached
the end of their life must be collected separately and returned to an
environmentally compatible recycling facility. Check with your local authority
or retailer for recycling advice and collection point.
| Belt speed no load
| Voltage
| Direct Current
| European Conformity Mark
| British
Conformity Mark
| Ukraine
Conformity Mark
| EurAsian Conformity Mark
EC DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfills all the relevant regulations and directives listed below and that the following harmonized standards have been used.
2011/65/EU (RoHS)
2014/30/EU
2006/42/EC
EN 62841-1:2015
EN 62841-2-4:2014
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
Winnenden, 2022-05-28
Alexander Krug
Managing Director
Authorized to compile the technical file
S.I. 2008/1597 (as amended)
S.I. 2016/1091 (as amended)
S.I. 2012/3032 (as amended)
BS EN 62841-1:2015
BS EN 62841-2-4:2014
BS EN IEC 55014-1:2021
BS EN IEC 55014-2:2021
BS EN IEC 63000:2018
Winnenden, 2022-05-28
Alexander Krug
Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
Authorized to compile the technical file:
Techtronic Industries (UK) Ltd
Parkway
Marlow, SL7 1YL
UK
Customer Support
Copyright 2022
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
+49 (0) 7195-12-0
www.milwaukeetool.eu
Techtronic Industries (UK) Ltd
Parkway
Marlow, SL7 1YL
UK
Documents / Resources
|
milwaukee M12 FBFL10 10mm Brushless Belt Sander
File
[pdf] Instruction Manual
M12 FBFL10, M12 FBFL13, M12 FBFL10 10mm Brushless Belt Sander File, 10mm
Brushless Belt Sander File, Brushless Belt Sander File, Belt Sander File,
Sander File, File
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>